[PATCH 4/5] iio: adc: ad7606: Add support for software mode for ad7616

Jonathan Cameron jic23 at kernel.org
Sat May 18 10:20:50 UTC 2019


On Thu, 16 May 2019 17:32:07 +0300
Beniamin Bia <beniamin.bia at analog.com> wrote:

> Support for ad7616 running in software was added. In order
> to activate the software mode, HW_RNGSEL pins must be pulled low.
> Oversampling and input ranges are now configured in corresponding
> registers. Ad7616 has multiple scale options when it is configured
> in software mode.
> 
> Signed-off-by: Beniamin Bia <beniamin.bia at analog.com>
Looks good subject to comments on the previous.

Thanks,

Jonathan

> ---
>  drivers/iio/adc/ad7606.c | 111 ++++++++++++++++++++++++++++++++++++---
>  1 file changed, 103 insertions(+), 8 deletions(-)
> 
> diff --git a/drivers/iio/adc/ad7606.c b/drivers/iio/adc/ad7606.c
> index 6df81117cacc..f77df3efe43f 100644
> --- a/drivers/iio/adc/ad7606.c
> +++ b/drivers/iio/adc/ad7606.c
> @@ -29,6 +29,20 @@
>  
>  #include "ad7606.h"
>  
> +#define AD7606_RANGE_CH_ADDR(ch)	(0x03 + ((ch) >> 1))
> +#define AD7606_OS_MODE			0x08
> +
> +#define AD7616_CONFIGURATION_REGISTER	0x02
> +#define AD7616_OS_MASK			GENMASK(4,  2)
> +#define AD7616_BURST_MODE		BIT(6)
> +#define AD7616_SEQEN_MODE		BIT(5)
> +#define AD7616_RANGE_CH_ADDR_OFF	0x04
> +#define AD7616_RANGE_CH_ADDR(ch)	((((ch) & 0x1) << 1) + ((ch) >> 3))
> +#define AD7616_RANGE_CH_MSK(ch)		(GENMASK(1, 0) << ((ch) & 0x6))
> +#define AD7616_RANGE_CH_MODE(ch, mode)	((mode) << (ch & GENMASK(2, 1)))
> +
> +static int ad7616_sw_mode_config(struct iio_dev *indio_dev);
> +
>  /*
>   * Scales are computed as 5000/32768 and 10000/32768 respectively,
>   * so that when applied to the raw values they provide mV values
> @@ -37,6 +51,11 @@ static const unsigned int ad7606_scale_avail[2] = {
>  	152588, 305176
>  };
>  
> +
> +static const unsigned int ad7616_sw_scale_avail[3] = {
> +	76293, 152588, 305176
> +};
> +
>  static const unsigned int ad7606_oversampling_avail[7] = {
>  	1, 2, 4, 8, 16, 32, 64,
>  };
> @@ -282,6 +301,26 @@ static int ad7606_write_os_hw(struct iio_dev *indio_dev, int val)
>  	return 0;
>  }
>  
> +static int ad7616_write_scale_sw(struct iio_dev *indio_dev, int ch, int val)
> +{
> +	struct ad7606_state *st = iio_priv(indio_dev);
> +	unsigned int ch_addr, mode;
> +
> +	ch_addr = AD7616_RANGE_CH_ADDR_OFF + AD7616_RANGE_CH_ADDR(ch);
> +	mode = AD7616_RANGE_CH_MODE(ch, ((val + 1) & 0x3));
> +
> +	return ad7606_spi_write_mask(st, ch_addr, AD7616_RANGE_CH_MSK(ch),
> +				     mode);
> +}
> +
> +static int ad7616_write_os_sw(struct iio_dev *indio_dev, int val)
> +{
> +	struct ad7606_state *st = iio_priv(indio_dev);
> +
> +	return ad7606_spi_write_mask(st, AD7616_CONFIGURATION_REGISTER,
> +				     AD7616_OS_MASK, val << 2);
> +}
> +
>  static int ad7606_write_raw(struct iio_dev *indio_dev,
>  			    struct iio_chan_spec const *chan,
>  			    int val,
> @@ -368,14 +407,14 @@ static const struct attribute_group ad7606_attribute_group_range = {
>  	.attrs = ad7606_attributes_range,
>  };
>  
> -#define AD760X_CHANNEL(num, mask) {				\
> +#define AD760X_CHANNEL(num, mask_sep, mask_type, mask_all) {	\
>  		.type = IIO_VOLTAGE,				\
>  		.indexed = 1,					\
>  		.channel = num,					\
>  		.address = num,					\
> -		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),	\
> -		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),\
> -		.info_mask_shared_by_all = mask,		\
> +		.info_mask_separate = mask_sep,			\
> +		.info_mask_shared_by_type = mask_type,		\
> +		.info_mask_shared_by_all = mask_all,		\
>  		.scan_index = num,				\
>  		.scan_type = {					\
>  			.sign = 's',				\
> @@ -385,11 +424,18 @@ static const struct attribute_group ad7606_attribute_group_range = {
>  		},						\
>  }
>  
> -#define AD7605_CHANNEL(num)	\
> -	AD760X_CHANNEL(num, 0)
> +#define AD7605_CHANNEL(num)				\
> +	AD760X_CHANNEL(num, BIT(IIO_CHAN_INFO_RAW),	\
> +		BIT(IIO_CHAN_INFO_SCALE), 0)
> +
> +#define AD7606_CHANNEL(num)				\
> +	AD760X_CHANNEL(num, BIT(IIO_CHAN_INFO_RAW),	\
> +		BIT(IIO_CHAN_INFO_SCALE),		\
> +		BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO))
>  
> -#define AD7606_CHANNEL(num)	\
> -	AD760X_CHANNEL(num, BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO))
> +#define AD7616_CHANNEL(num)	\
> +	AD760X_CHANNEL(num, BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE),\
> +		0, BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO))
>  
>  static const struct iio_chan_spec ad7605_channels[] = {
>  	IIO_CHAN_SOFT_TIMESTAMP(4),
> @@ -441,6 +487,26 @@ static const struct iio_chan_spec ad7616_channels[] = {
>  	AD7606_CHANNEL(15),
>  };
>  
> +static const struct iio_chan_spec ad7616_sw_channels[] = {
> +	IIO_CHAN_SOFT_TIMESTAMP(16),
> +	AD7616_CHANNEL(0),
> +	AD7616_CHANNEL(1),
> +	AD7616_CHANNEL(2),
> +	AD7616_CHANNEL(3),
> +	AD7616_CHANNEL(4),
> +	AD7616_CHANNEL(5),
> +	AD7616_CHANNEL(6),
> +	AD7616_CHANNEL(7),
> +	AD7616_CHANNEL(8),
> +	AD7616_CHANNEL(9),
> +	AD7616_CHANNEL(10),
> +	AD7616_CHANNEL(11),
> +	AD7616_CHANNEL(12),
> +	AD7616_CHANNEL(13),
> +	AD7616_CHANNEL(14),
> +	AD7616_CHANNEL(15),
> +};
> +
>  static const struct ad7606_chip_info ad7606_chip_info_tbl[] = {
>  	/* More devices added in future */
>  	[ID_AD7605_4] = {
> @@ -468,9 +534,13 @@ static const struct ad7606_chip_info ad7606_chip_info_tbl[] = {
>  	[ID_AD7616] = {
>  		.channels = ad7616_channels,
>  		.num_channels = 17,
> +		.sw_mode_config = ad7616_sw_mode_config,
>  		.oversampling_avail = ad7616_oversampling_avail,
>  		.oversampling_num = ARRAY_SIZE(ad7616_oversampling_avail),
>  		.os_req_reset = true,
> +		.spi_rd_wr_cmd = ad7616_spi_rd_wr_cmd,
> +		.write_scale_sw = ad7616_write_scale_sw,
> +		.write_os_sw = ad7616_write_os_sw,
>  	},
>  };
>  
> @@ -604,6 +674,23 @@ static void ad7606_regulator_disable(void *data)
>  	regulator_disable(st->reg);
>  }
>  
> +static int ad7616_sw_mode_config(struct iio_dev *indio_dev)
> +{
> +	struct ad7606_state *st = iio_priv(indio_dev);
> +
> +	/*
> +	 * Scale can be configured individually for each channel
> +	 * in software mode.
> +	 */
> +	indio_dev->channels = ad7616_sw_channels;
> +
> +	/* Activate Burst mode and SEQEN MODE */
> +	return ad7606_spi_write_mask(st,
> +			      AD7616_CONFIGURATION_REGISTER,
> +			      AD7616_BURST_MODE | AD7616_SEQEN_MODE,
> +			      AD7616_BURST_MODE | AD7616_SEQEN_MODE);
> +}
> +
>  int ad7606_probe(struct device *dev, int irq, void __iomem *base_address,
>  		 const char *name, unsigned int id,
>  		 const struct ad7606_bus_ops *bops)
> @@ -677,6 +764,10 @@ int ad7606_probe(struct device *dev, int irq, void __iomem *base_address,
>  	if (ret)
>  		dev_warn(st->dev, "failed to RESET: no RESET GPIO specified\n");
>  
> +	/* AD7616 requires al least 15ms to reconfigure after a reset */
> +	if (msleep_interruptible(15))
> +		return -ERESTARTSYS;
> +
>  	st->write_scale = ad7606_write_scale_hw;
>  	st->write_os = ad7606_write_os_hw;
>  
> @@ -685,6 +776,10 @@ int ad7606_probe(struct device *dev, int irq, void __iomem *base_address,
>  							 "adi,sw-mode");
>  
>  	if (st->sw_mode_en) {
> +		/* Scale of 0.076293 is only available in sw mode */
> +		st->scale_avail = ad7616_sw_scale_avail;
> +		st->num_scales = ARRAY_SIZE(ad7616_sw_scale_avail);
> +
>  		/* After reset, in software mode, ±10 V is set by default */
>  		memset32(st->range, 2, ARRAY_SIZE(st->range));
>  		indio_dev->info = &ad7606_info_os_and_range;



More information about the devel mailing list