[PATCH v2 2/9] Staging: iio: accel: adis16201: Remove unnecessary comments

Himanshu Jha himanshujha199640 at gmail.com
Fri Mar 16 20:06:19 UTC 2018


Remove few unnecessary comments since the macro definitions clearly
justify their purpose.

Signed-off-by: Himanshu Jha <himanshujha199640 at gmail.com>
---
v2:
   -reodered patch series.

 drivers/staging/iio/accel/adis16201.c | 36 -----------------------------------
 1 file changed, 36 deletions(-)

diff --git a/drivers/staging/iio/accel/adis16201.c b/drivers/staging/iio/accel/adis16201.c
index 767ebf0..6c06c0d 100644
--- a/drivers/staging/iio/accel/adis16201.c
+++ b/drivers/staging/iio/accel/adis16201.c
@@ -22,96 +22,66 @@
 
 #define ADIS16201_STARTUP_DELAY_MS	220
 
-/* Flash memory write count */
 #define ADIS16201_FLASH_CNT      0x00
 
-/* Output, power supply */
 #define ADIS16201_SUPPLY_OUT     0x02
 
-/* Output, x-axis accelerometer */
 #define ADIS16201_XACCL_OUT      0x04
 
-/* Output, y-axis accelerometer */
 #define ADIS16201_YACCL_OUT      0x06
 
-/* Output, auxiliary ADC input */
 #define ADIS16201_AUX_ADC        0x08
 
-/* Output, temperature */
 #define ADIS16201_TEMP_OUT       0x0A
 
-/* Output, x-axis inclination */
 #define ADIS16201_XINCL_OUT      0x0C
 
-/* Output, y-axis inclination */
 #define ADIS16201_YINCL_OUT      0x0E
 
-/* Calibration, x-axis acceleration offset */
 #define ADIS16201_XACCL_OFFS     0x10
 
-/* Calibration, y-axis acceleration offset */
 #define ADIS16201_YACCL_OFFS     0x12
 
-/* x-axis acceleration scale factor */
 #define ADIS16201_XACCL_SCALE    0x14
 
-/* y-axis acceleration scale factor */
 #define ADIS16201_YACCL_SCALE    0x16
 
-/* Calibration, x-axis inclination offset */
 #define ADIS16201_XINCL_OFFS     0x18
 
-/* Calibration, y-axis inclination offset */
 #define ADIS16201_YINCL_OFFS     0x1A
 
-/* x-axis inclination scale factor */
 #define ADIS16201_XINCL_SCALE    0x1C
 
-/* y-axis inclination scale factor */
 #define ADIS16201_YINCL_SCALE    0x1E
 
-/* Alarm 1 amplitude threshold */
 #define ADIS16201_ALM_MAG1       0x20
 
-/* Alarm 2 amplitude threshold */
 #define ADIS16201_ALM_MAG2       0x22
 
-/* Alarm 1, sample period */
 #define ADIS16201_ALM_SMPL1      0x24
 
-/* Alarm 2, sample period */
 #define ADIS16201_ALM_SMPL2      0x26
 
-/* Alarm control */
 #define ADIS16201_ALM_CTRL       0x28
 
-/* Auxiliary DAC data */
 #define ADIS16201_AUX_DAC        0x30
 
-/* General-purpose digital input/output control */
 #define ADIS16201_GPIO_CTRL      0x32
 
-/* Miscellaneous control */
 #define ADIS16201_MSC_CTRL       0x34
 
-/* Internal sample period (rate) control */
 #define ADIS16201_SMPL_PRD       0x36
 
 /* Operation, filter configuration */
 #define ADIS16201_AVG_CNT        0x38
 
-/* Operation, sleep mode control */
 #define ADIS16201_SLP_CNT        0x3A
 
-/* Diagnostics, system status register */
 #define ADIS16201_DIAG_STAT      0x3C
 
-/* Operation, system command register */
 #define ADIS16201_GLOB_CMD       0x3E
 
-/* MSC_CTRL */
 
-/* Self-test enable */
 #define ADIS16201_MSC_CTRL_SELF_TEST_EN	        BIT(8)
 
 /* Data-ready enable: 1 = enabled, 0 = disabled */
@@ -123,18 +93,13 @@
 /* Data-ready line selection: 1 = DIO1, 0 = DIO0 */
 #define ADIS16201_MSC_CTRL_DATA_RDY_DIO1	BIT(0)
 
-/* DIAG_STAT */
 
-/* Alarm 2 status: 1 = alarm active, 0 = alarm inactive */
 #define ADIS16201_DIAG_STAT_ALARM2        BIT(9)
 
-/* Alarm 1 status: 1 = alarm active, 0 = alarm inactive */
 #define ADIS16201_DIAG_STAT_ALARM1        BIT(8)
 
-/* SPI communications failure */
 #define ADIS16201_DIAG_STAT_SPI_FAIL_BIT   3
 
-/* Flash update failure */
 #define ADIS16201_DIAG_STAT_FLASH_UPT_FAIL_BIT  2
 
 /* Power supply above 3.625 V */
@@ -143,7 +108,6 @@
 /* Power supply below 3.15 V */
 #define ADIS16201_DIAG_STAT_POWER_LOW_BIT  0
 
-/* GLOB_CMD */
 
 #define ADIS16201_GLOB_CMD_SW_RESET	BIT(7)
 #define ADIS16201_GLOB_CMD_FACTORY_RESET	BIT(1)
-- 
2.7.4



More information about the devel mailing list