[PATCH 1/8] staging: mt7621-gpio: make use 'bgpio_init' from GPIO_GENERIC
NeilBrown
neil at brown.name
Sun Jun 10 08:53:04 UTC 2018
On Sat, Jun 09 2018, Sergio Paracuellos wrote:
> Gpio complexity is just masking the fact that offset is always
> 0..n and writes to bits 0..n of some memory address. Because
> of this whole thing can just me converted to use GPIO_GENERIC
> and avoid duplications of a lot of driver custom functions.
> So use bgpio_init instead of custom code adding GPIO_GENERIC
> dependency to the Kconfig file. Also to make easier using
> bgpio_init function offset for each gpio bank, enumeration
> where register were defined has been replaced in favour of
> some macros which handle each gpio offset taking into account
> the bank where are located. Because of this change write and
> read functions which are being used for remaining irq handling
> stuff have been updated also as well as its dependencies along
> the code.
Thanks for this. It is a big change, and unsurprisingly there are a few
bugs.
I haven't actually got the driver working yet so there is still
something not quite right after the things listed here get fixed.
Firstly, I don't think it is useful to create the macros that you
describe above. Every time we access a register, we have an 'rg' which
has a bank number in it so I think it is much better to do the
multiplication in the read/write functions rather than in the macro.
But that isn't a bug exactly.... read on..
>
> Signed-off-by: Sergio Paracuellos <sergio.paracuellos at gmail.com>
> ---
> drivers/staging/mt7621-gpio/Kconfig | 1 +
> drivers/staging/mt7621-gpio/gpio-mt7621.c | 148 ++++++++++--------------------
> 2 files changed, 47 insertions(+), 102 deletions(-)
>
> diff --git a/drivers/staging/mt7621-gpio/Kconfig b/drivers/staging/mt7621-gpio/Kconfig
> index c741ec3..f4453e8 100644
> --- a/drivers/staging/mt7621-gpio/Kconfig
> +++ b/drivers/staging/mt7621-gpio/Kconfig
> @@ -1,6 +1,7 @@
> config GPIO_MT7621
> bool "Mediatek GPIO Support"
> depends on SOC_MT7620 || SOC_MT7621
> + select GPIO_GENERIC
> select ARCH_REQUIRE_GPIOLIB
> help
> Say yes here to support the Mediatek SoC GPIO device
> diff --git a/drivers/staging/mt7621-gpio/gpio-mt7621.c b/drivers/staging/mt7621-gpio/gpio-mt7621.c
> index 0c4fb4a..cc08505 100644
> --- a/drivers/staging/mt7621-gpio/gpio-mt7621.c
> +++ b/drivers/staging/mt7621-gpio/gpio-mt7621.c
> @@ -19,19 +19,18 @@
> #define MTK_BANK_WIDTH 32
> #define PIN_MASK(nr) (1UL << ((nr % MTK_BANK_WIDTH)))
>
> -enum mediatek_gpio_reg {
> - GPIO_REG_CTRL = 0,
> - GPIO_REG_POL,
> - GPIO_REG_DATA,
> - GPIO_REG_DSET,
> - GPIO_REG_DCLR,
> - GPIO_REG_REDGE,
> - GPIO_REG_FEDGE,
> - GPIO_REG_HLVL,
> - GPIO_REG_LLVL,
> - GPIO_REG_STAT,
> - GPIO_REG_EDGE,
> -};
> +#define GPIO_BANK_WIDE 0x04
> +#define GPIO_REG_CTRL(bank) (((bank) * GPIO_BANK_WIDE) + 0x00)
> +#define GPIO_REG_POL(bank) (((bank) * GPIO_BANK_WIDE) + 0x10)
> +#define GPIO_REG_DATA(bank) (((bank) * GPIO_BANK_WIDE) + 0x20)
> +#define GPIO_REG_DSET(bank) (((bank) * GPIO_BANK_WIDE) + 0x30)
> +#define GPIO_REG_DCLR(bank) (((bank) * GPIO_BANK_WIDE) + 0x40)
> +#define GPIO_REG_REDGE(bank) (((bank) * GPIO_BANK_WIDE) + 0x50)
> +#define GPIO_REG_FEDGE(bank) (((bank) * GPIO_BANK_WIDE) + 0x60)
> +#define GPIO_REG_HLVL(bank) (((bank) * GPIO_BANK_WIDE) + 0x70)
> +#define GPIO_REG_LLVL(bank) (((bank) * GPIO_BANK_WIDE) + 0x80)
> +#define GPIO_REG_STAT(bank) (((bank) * GPIO_BANK_WIDE) + 0x90)
> +#define GPIO_REG_EDGE(bank) (((bank) * GPIO_BANK_WIDE) + 0xA0)
>
> struct mtk_gc {
> struct gpio_chip chip;
> @@ -55,80 +54,21 @@ to_mediatek_gpio(struct gpio_chip *chip)
> }
>
> static inline void
> -mtk_gpio_w32(struct mtk_gc *rg, u8 reg, u32 val)
> +mtk_gpio_w32(struct mtk_gc *rg, u32 offset, u32 val)
> {
> - struct mtk_data *gpio_data = gpiochip_get_data(&rg->chip);
> - u32 offset = (reg * 0x10) + (rg->bank * 0x4);
> + struct gpio_chip *gc = &rg->chip;
> + struct mtk_data *gpio_data = gpiochip_get_data(gc);
>
> - iowrite32(val, gpio_data->gpio_membase + offset);
> + gc->write_reg(gpio_data->gpio_membase + offset, val);
> }
>
> static inline u32
> -mtk_gpio_r32(struct mtk_gc *rg, u8 reg)
> -{
> - struct mtk_data *gpio_data = gpiochip_get_data(&rg->chip);
> - u32 offset = (reg * 0x10) + (rg->bank * 0x4);
> -
> - return ioread32(gpio_data->gpio_membase + offset);
> -}
> -
> -static void
> -mediatek_gpio_set(struct gpio_chip *chip, unsigned int offset, int value)
> -{
> - struct mtk_gc *rg = to_mediatek_gpio(chip);
> -
> - mtk_gpio_w32(rg, (value) ? GPIO_REG_DSET : GPIO_REG_DCLR, BIT(offset));
> -}
> -
> -static int
> -mediatek_gpio_get(struct gpio_chip *chip, unsigned int offset)
> -{
> - struct mtk_gc *rg = to_mediatek_gpio(chip);
> -
> - return !!(mtk_gpio_r32(rg, GPIO_REG_DATA) & BIT(offset));
> -}
> -
> -static int
> -mediatek_gpio_direction_input(struct gpio_chip *chip, unsigned int offset)
> -{
> - struct mtk_gc *rg = to_mediatek_gpio(chip);
> - unsigned long flags;
> - u32 t;
> -
> - spin_lock_irqsave(&rg->lock, flags);
> - t = mtk_gpio_r32(rg, GPIO_REG_CTRL);
> - t &= ~BIT(offset);
> - mtk_gpio_w32(rg, GPIO_REG_CTRL, t);
> - spin_unlock_irqrestore(&rg->lock, flags);
> -
> - return 0;
> -}
> -
> -static int
> -mediatek_gpio_direction_output(struct gpio_chip *chip,
> - unsigned int offset, int value)
> +mtk_gpio_r32(struct mtk_gc *rg, u32 offset)
> {
> - struct mtk_gc *rg = to_mediatek_gpio(chip);
> - unsigned long flags;
> - u32 t;
> -
> - spin_lock_irqsave(&rg->lock, flags);
> - t = mtk_gpio_r32(rg, GPIO_REG_CTRL);
> - t |= BIT(offset);
> - mtk_gpio_w32(rg, GPIO_REG_CTRL, t);
> - mediatek_gpio_set(chip, offset, value);
> - spin_unlock_irqrestore(&rg->lock, flags);
> + struct gpio_chip *gc = &rg->chip;
> + struct mtk_data *gpio_data = gpiochip_get_data(gc);
>
> - return 0;
> -}
> -
> -static int
> -mediatek_gpio_get_direction(struct gpio_chip *chip, unsigned int offset)
> -{
> - struct mtk_gc *rg = to_mediatek_gpio(chip);
> - u32 t = mtk_gpio_r32(rg, GPIO_REG_CTRL);
> -
> - return (t & BIT(offset)) ? GPIOF_DIR_OUT : GPIOF_DIR_IN;
> + return gc->read_reg(gpio_data->gpio_membase + offset);
> }
>
> static int
> @@ -156,20 +96,22 @@ mediatek_gpio_bank_probe(struct platform_device *pdev, struct device_node *bank)
> memset(rg, 0, sizeof(*rg));
>
> spin_lock_init(&rg->lock);
> + rg->bank = be32_to_cpu(*id);
> +
> + ret = bgpio_init(&rg->chip, &pdev->dev, 4,
> + gpio_data->gpio_membase + GPIO_REG_DATA(rg->bank),
> + gpio_data->gpio_membase + GPIO_REG_DSET(rg->bank),
> + gpio_data->gpio_membase + GPIO_REG_DCLR(rg->bank),
> + gpio_data->gpio_membase + GPIO_REG_CTRL(rg->bank),
> + gpio_data->gpio_membase + GPIO_REG_CTRL(rg->bank),
> + 0);
This is the first problem I git. You've provided both 'dirout' and
'dirin' and that is not permitted. You've given exactly the same value
for both, which isn't really meaningful.
dirout is correct, dirin should be NULL.
> + if (ret) {
> + dev_err(&pdev->dev, "bgpio_init() failed\n");
> + return ret;
> + }
>
> - rg->chip.parent = &pdev->dev;
> - rg->chip.label = dev_name(&pdev->dev);
> - rg->chip.of_node = bank;
> - rg->chip.base = MTK_BANK_WIDTH * be32_to_cpu(*id);
These last two are still needed - bgpio_init doesn't set them up.
I think that is all in this patch.
Thanks,
NeilBrown
> - rg->chip.ngpio = MTK_BANK_WIDTH;
> - rg->chip.direction_input = mediatek_gpio_direction_input;
> - rg->chip.direction_output = mediatek_gpio_direction_output;
> - rg->chip.get_direction = mediatek_gpio_get_direction;
> - rg->chip.get = mediatek_gpio_get;
> - rg->chip.set = mediatek_gpio_set;
> if (gpio_data->gpio_irq_domain)
> rg->chip.to_irq = mediatek_gpio_to_irq;
> - rg->bank = be32_to_cpu(*id);
>
> ret = devm_gpiochip_add_data(&pdev->dev, &rg->chip, gpio_data);
> if (ret < 0) {
> @@ -179,7 +121,7 @@ mediatek_gpio_bank_probe(struct platform_device *pdev, struct device_node *bank)
> }
>
> /* set polarity to low for all gpios */
> - mtk_gpio_w32(rg, GPIO_REG_POL, 0);
> + mtk_gpio_w32(rg, GPIO_REG_POL(rg->bank), 0);
>
> dev_info(&pdev->dev, "registering %d gpios\n", rg->chip.ngpio);
>
> @@ -200,14 +142,14 @@ mediatek_gpio_irq_handler(struct irq_desc *desc)
> if (!rg)
> continue;
>
> - pending = mtk_gpio_r32(rg, GPIO_REG_STAT);
> + pending = mtk_gpio_r32(rg, GPIO_REG_STAT(rg->bank));
>
> for_each_set_bit(bit, &pending, MTK_BANK_WIDTH) {
> u32 map = irq_find_mapping(gpio_data->gpio_irq_domain,
> (MTK_BANK_WIDTH * i) + bit);
>
> generic_handle_irq(map);
> - mtk_gpio_w32(rg, GPIO_REG_STAT, BIT(bit));
> + mtk_gpio_w32(rg, GPIO_REG_STAT(i), BIT(bit));
> }
> }
> }
> @@ -226,10 +168,12 @@ mediatek_gpio_irq_unmask(struct irq_data *d)
> return;
>
> spin_lock_irqsave(&rg->lock, flags);
> - rise = mtk_gpio_r32(rg, GPIO_REG_REDGE);
> - fall = mtk_gpio_r32(rg, GPIO_REG_FEDGE);
> - mtk_gpio_w32(rg, GPIO_REG_REDGE, rise | (PIN_MASK(pin) & rg->rising));
> - mtk_gpio_w32(rg, GPIO_REG_FEDGE, fall | (PIN_MASK(pin) & rg->falling));
> + rise = mtk_gpio_r32(rg, GPIO_REG_REDGE(bank));
> + fall = mtk_gpio_r32(rg, GPIO_REG_FEDGE(bank));
> + mtk_gpio_w32(rg, GPIO_REG_REDGE(bank),
> + rise | (PIN_MASK(pin) & rg->rising));
> + mtk_gpio_w32(rg, GPIO_REG_FEDGE(bank),
> + fall | (PIN_MASK(pin) & rg->falling));
> spin_unlock_irqrestore(&rg->lock, flags);
> }
>
> @@ -247,10 +191,10 @@ mediatek_gpio_irq_mask(struct irq_data *d)
> return;
>
> spin_lock_irqsave(&rg->lock, flags);
> - rise = mtk_gpio_r32(rg, GPIO_REG_REDGE);
> - fall = mtk_gpio_r32(rg, GPIO_REG_FEDGE);
> - mtk_gpio_w32(rg, GPIO_REG_FEDGE, fall & ~PIN_MASK(pin));
> - mtk_gpio_w32(rg, GPIO_REG_REDGE, rise & ~PIN_MASK(pin));
> + rise = mtk_gpio_r32(rg, GPIO_REG_REDGE(bank));
> + fall = mtk_gpio_r32(rg, GPIO_REG_FEDGE(bank));
> + mtk_gpio_w32(rg, GPIO_REG_FEDGE(bank), fall & ~PIN_MASK(pin));
> + mtk_gpio_w32(rg, GPIO_REG_REDGE(bank), rise & ~PIN_MASK(pin));
> spin_unlock_irqrestore(&rg->lock, flags);
> }
>
> --
> 2.7.4
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 832 bytes
Desc: not available
URL: <http://driverdev.linuxdriverproject.org/pipermail/driverdev-devel/attachments/20180610/edf15aef/attachment-0001.asc>
More information about the devel
mailing list