[PATCH v5 02/12] gpu: ipu-csi: Swap fields according to input/output field types

Steve Longerbeam slongerbeam at gmail.com
Fri Dec 7 20:02:23 UTC 2018


Hi Philipp, can you review this patch and give it your ack?

Thanks,
Steve


On 10/16/18 5:00 PM, Steve Longerbeam wrote:
> The function ipu_csi_init_interface() was inverting the F-bit for
> NTSC case, in the CCIR_CODE_1/2 registers. The result being that
> for NTSC bottom-top field order, the CSI would swap fields and
> capture in top-bottom order.
>
> Instead, base field swap on the field order of the input to the CSI,
> and the field order of the requested output. If the input/output
> fields are sequential but different, swap fields, otherwise do
> not swap. This requires passing both the input and output mbus
> frame formats to ipu_csi_init_interface().
>
> Move this code to a new private function ipu_csi_set_bt_interlaced_codes()
> that programs the CCIR_CODE_1/2 registers for interlaced BT.656 (and
> possibly interlaced BT.1120 in the future).
>
> When detecting input video standard from the input frame width/height,
> make sure to double height if input field type is alternate, since
> in that case input height only includes lines for one field.
>
> Signed-off-by: Steve Longerbeam <slongerbeam at gmail.com>
> ---
> Changes since v4:
> - Cleaned up some convoluted code in ipu_csi_init_interface(), suggested
>    by Philipp Zabel.
> - Fixed a regression in csi_setup(), caught by Philipp.
> ---
>   drivers/gpu/ipu-v3/ipu-csi.c              | 119 +++++++++++++++-------
>   drivers/staging/media/imx/imx-media-csi.c |  17 +---
>   include/video/imx-ipu-v3.h                |   3 +-
>   3 files changed, 88 insertions(+), 51 deletions(-)
>
> diff --git a/drivers/gpu/ipu-v3/ipu-csi.c b/drivers/gpu/ipu-v3/ipu-csi.c
> index aa0e30a2ba18..4a15e513fa05 100644
> --- a/drivers/gpu/ipu-v3/ipu-csi.c
> +++ b/drivers/gpu/ipu-v3/ipu-csi.c
> @@ -325,6 +325,15 @@ static int mbus_code_to_bus_cfg(struct ipu_csi_bus_config *cfg, u32 mbus_code,
>   	return 0;
>   }
>   
> +/* translate alternate field mode based on given standard */
> +static inline enum v4l2_field
> +ipu_csi_translate_field(enum v4l2_field field, v4l2_std_id std)
> +{
> +	return (field != V4L2_FIELD_ALTERNATE) ? field :
> +		((std & V4L2_STD_525_60) ?
> +		 V4L2_FIELD_SEQ_BT : V4L2_FIELD_SEQ_TB);
> +}
> +
>   /*
>    * Fill a CSI bus config struct from mbus_config and mbus_framefmt.
>    */
> @@ -374,22 +383,75 @@ static int fill_csi_bus_cfg(struct ipu_csi_bus_config *csicfg,
>   	return 0;
>   }
>   
> +static int ipu_csi_set_bt_interlaced_codes(struct ipu_csi *csi,
> +					   struct v4l2_mbus_framefmt *infmt,
> +					   struct v4l2_mbus_framefmt *outfmt,
> +					   v4l2_std_id std)
> +{
> +	enum v4l2_field infield, outfield;
> +	bool swap_fields;
> +
> +	/* get translated field type of input and output */
> +	infield = ipu_csi_translate_field(infmt->field, std);
> +	outfield = ipu_csi_translate_field(outfmt->field, std);
> +
> +	/*
> +	 * Write the H-V-F codes the CSI will match against the
> +	 * incoming data for start/end of active and blanking
> +	 * field intervals. If input and output field types are
> +	 * sequential but not the same (one is SEQ_BT and the other
> +	 * is SEQ_TB), swap the F-bit so that the CSI will capture
> +	 * field 1 lines before field 0 lines.
> +	 */
> +	swap_fields = (V4L2_FIELD_IS_SEQUENTIAL(infield) &&
> +		       V4L2_FIELD_IS_SEQUENTIAL(outfield) &&
> +		       infield != outfield);
> +
> +	if (!swap_fields) {
> +		/*
> +		 * Field0BlankEnd  = 110, Field0BlankStart  = 010
> +		 * Field0ActiveEnd = 100, Field0ActiveStart = 000
> +		 * Field1BlankEnd  = 111, Field1BlankStart  = 011
> +		 * Field1ActiveEnd = 101, Field1ActiveStart = 001
> +		 */
> +		ipu_csi_write(csi, 0x40596 | CSI_CCIR_ERR_DET_EN,
> +			      CSI_CCIR_CODE_1);
> +		ipu_csi_write(csi, 0xD07DF, CSI_CCIR_CODE_2);
> +	} else {
> +		dev_dbg(csi->ipu->dev, "capture field swap\n");
> +
> +		/* same as above but with F-bit inverted */
> +		ipu_csi_write(csi, 0xD07DF | CSI_CCIR_ERR_DET_EN,
> +			      CSI_CCIR_CODE_1);
> +		ipu_csi_write(csi, 0x40596, CSI_CCIR_CODE_2);
> +	}
> +
> +	ipu_csi_write(csi, 0xFF0000, CSI_CCIR_CODE_3);
> +
> +	return 0;
> +}
> +
> +
>   int ipu_csi_init_interface(struct ipu_csi *csi,
>   			   struct v4l2_mbus_config *mbus_cfg,
> -			   struct v4l2_mbus_framefmt *mbus_fmt)
> +			   struct v4l2_mbus_framefmt *infmt,
> +			   struct v4l2_mbus_framefmt *outfmt)
>   {
>   	struct ipu_csi_bus_config cfg;
>   	unsigned long flags;
>   	u32 width, height, data = 0;
> +	v4l2_std_id std;
>   	int ret;
>   
> -	ret = fill_csi_bus_cfg(&cfg, mbus_cfg, mbus_fmt);
> +	ret = fill_csi_bus_cfg(&cfg, mbus_cfg, infmt);
>   	if (ret < 0)
>   		return ret;
>   
>   	/* set default sensor frame width and height */
> -	width = mbus_fmt->width;
> -	height = mbus_fmt->height;
> +	width = infmt->width;
> +	height = infmt->height;
> +	if (infmt->field == V4L2_FIELD_ALTERNATE)
> +		height *= 2;
>   
>   	/* Set the CSI_SENS_CONF register remaining fields */
>   	data |= cfg.data_width << CSI_SENS_CONF_DATA_WIDTH_SHIFT |
> @@ -416,42 +478,22 @@ int ipu_csi_init_interface(struct ipu_csi *csi,
>   		ipu_csi_write(csi, 0xFF0000, CSI_CCIR_CODE_3);
>   		break;
>   	case IPU_CSI_CLK_MODE_CCIR656_INTERLACED:
> -		if (mbus_fmt->width == 720 && mbus_fmt->height == 576) {
> -			/*
> -			 * PAL case
> -			 *
> -			 * Field0BlankEnd = 0x6, Field0BlankStart = 0x2,
> -			 * Field0ActiveEnd = 0x4, Field0ActiveStart = 0
> -			 * Field1BlankEnd = 0x7, Field1BlankStart = 0x3,
> -			 * Field1ActiveEnd = 0x5, Field1ActiveStart = 0x1
> -			 */
> -			height = 625; /* framelines for PAL */
> -
> -			ipu_csi_write(csi, 0x40596 | CSI_CCIR_ERR_DET_EN,
> -					  CSI_CCIR_CODE_1);
> -			ipu_csi_write(csi, 0xD07DF, CSI_CCIR_CODE_2);
> -			ipu_csi_write(csi, 0xFF0000, CSI_CCIR_CODE_3);
> -		} else if (mbus_fmt->width == 720 && mbus_fmt->height == 480) {
> -			/*
> -			 * NTSC case
> -			 *
> -			 * Field0BlankEnd = 0x7, Field0BlankStart = 0x3,
> -			 * Field0ActiveEnd = 0x5, Field0ActiveStart = 0x1
> -			 * Field1BlankEnd = 0x6, Field1BlankStart = 0x2,
> -			 * Field1ActiveEnd = 0x4, Field1ActiveStart = 0
> -			 */
> -			height = 525; /* framelines for NTSC */
> -
> -			ipu_csi_write(csi, 0xD07DF | CSI_CCIR_ERR_DET_EN,
> -					  CSI_CCIR_CODE_1);
> -			ipu_csi_write(csi, 0x40596, CSI_CCIR_CODE_2);
> -			ipu_csi_write(csi, 0xFF0000, CSI_CCIR_CODE_3);
> +		if (width == 720 && height == 480) {
> +			std = V4L2_STD_NTSC;
> +			height = 525;
> +		} else if (width == 720 && height == 576) {
> +			std = V4L2_STD_PAL;
> +			height = 625;
>   		} else {
>   			dev_err(csi->ipu->dev,
> -				"Unsupported CCIR656 interlaced video mode\n");
> -			spin_unlock_irqrestore(&csi->lock, flags);
> -			return -EINVAL;
> +				"Unsupported interlaced video mode\n");
> +			ret = -EINVAL;
> +			goto out_unlock;
>   		}
> +
> +		ret = ipu_csi_set_bt_interlaced_codes(csi, infmt, outfmt, std);
> +		if (ret)
> +			goto out_unlock;
>   		break;
>   	case IPU_CSI_CLK_MODE_CCIR1120_PROGRESSIVE_DDR:
>   	case IPU_CSI_CLK_MODE_CCIR1120_PROGRESSIVE_SDR:
> @@ -476,9 +518,10 @@ int ipu_csi_init_interface(struct ipu_csi *csi,
>   	dev_dbg(csi->ipu->dev, "CSI_ACT_FRM_SIZE = 0x%08X\n",
>   		ipu_csi_read(csi, CSI_ACT_FRM_SIZE));
>   
> +out_unlock:
>   	spin_unlock_irqrestore(&csi->lock, flags);
>   
> -	return 0;
> +	return ret;
>   }
>   EXPORT_SYMBOL_GPL(ipu_csi_init_interface);
>   
> diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
> index 4223f8d418ae..7ecbd4d76d09 100644
> --- a/drivers/staging/media/imx/imx-media-csi.c
> +++ b/drivers/staging/media/imx/imx-media-csi.c
> @@ -663,15 +663,14 @@ static void csi_idmac_stop(struct csi_priv *priv)
>   /* Update the CSI whole sensor and active windows */
>   static int csi_setup(struct csi_priv *priv)
>   {
> -	struct v4l2_mbus_framefmt *infmt, *outfmt;
> +	struct v4l2_mbus_framefmt infmt, outfmt;
>   	const struct imx_media_pixfmt *incc;
>   	struct v4l2_mbus_config mbus_cfg;
> -	struct v4l2_mbus_framefmt if_fmt;
>   	struct v4l2_rect crop;
>   
> -	infmt = &priv->format_mbus[CSI_SINK_PAD];
> +	infmt = priv->format_mbus[CSI_SINK_PAD];
>   	incc = priv->cc[CSI_SINK_PAD];
> -	outfmt = &priv->format_mbus[priv->active_output_pad];
> +	outfmt = priv->format_mbus[priv->active_output_pad];
>   
>   	/* compose mbus_config from the upstream endpoint */
>   	mbus_cfg.type = priv->upstream_ep.bus_type;
> @@ -679,12 +678,6 @@ static int csi_setup(struct csi_priv *priv)
>   		priv->upstream_ep.bus.parallel.flags :
>   		priv->upstream_ep.bus.mipi_csi2.flags;
>   
> -	/*
> -	 * we need to pass input frame to CSI interface, but
> -	 * with translated field type from output format
> -	 */
> -	if_fmt = *infmt;
> -	if_fmt.field = outfmt->field;
>   	crop = priv->crop;
>   
>   	/*
> @@ -692,7 +685,7 @@ static int csi_setup(struct csi_priv *priv)
>   	 * generic/bayer data
>   	 */
>   	if (is_parallel_bus(&priv->upstream_ep) && incc->cycles) {
> -		if_fmt.width *= incc->cycles;
> +		infmt.width *= incc->cycles;
>   		crop.width *= incc->cycles;
>   	}
>   
> @@ -702,7 +695,7 @@ static int csi_setup(struct csi_priv *priv)
>   			     priv->crop.width == 2 * priv->compose.width,
>   			     priv->crop.height == 2 * priv->compose.height);
>   
> -	ipu_csi_init_interface(priv->csi, &mbus_cfg, &if_fmt);
> +	ipu_csi_init_interface(priv->csi, &mbus_cfg, &infmt, &outfmt);
>   
>   	ipu_csi_set_dest(priv->csi, priv->dest);
>   
> diff --git a/include/video/imx-ipu-v3.h b/include/video/imx-ipu-v3.h
> index abbad94e14a1..f44a35192313 100644
> --- a/include/video/imx-ipu-v3.h
> +++ b/include/video/imx-ipu-v3.h
> @@ -352,7 +352,8 @@ int ipu_prg_channel_configure(struct ipuv3_channel *ipu_chan,
>   struct ipu_csi;
>   int ipu_csi_init_interface(struct ipu_csi *csi,
>   			   struct v4l2_mbus_config *mbus_cfg,
> -			   struct v4l2_mbus_framefmt *mbus_fmt);
> +			   struct v4l2_mbus_framefmt *infmt,
> +			   struct v4l2_mbus_framefmt *outfmt);
>   bool ipu_csi_is_interlaced(struct ipu_csi *csi);
>   void ipu_csi_get_window(struct ipu_csi *csi, struct v4l2_rect *w);
>   void ipu_csi_set_window(struct ipu_csi *csi, struct v4l2_rect *w);



More information about the devel mailing list