[PATCH v6 07/13] media: dt-bindings: add bindings for i.MX7 media driver
Rui Miguel Silva
rui.silva at linaro.org
Thu Aug 2 16:48:06 UTC 2018
Hi Sakari,
Thanks for the review.
I will take this in account when preparing the v7, all your
comments
bellow look reasonable to me.
---
Cheers,
Rui
On Thu 02 Aug 2018 at 14:00, Sakari Ailus wrote:
> Hi Rui,
>
> On Tue, May 22, 2018 at 03:52:39PM +0100, Rui Miguel Silva
> wrote:
>> Add bindings documentation for i.MX7 media drivers.
>> The imx7 MIPI CSI2 and imx7 CMOS Sensor Interface.
>>
>> Signed-off-by: Rui Miguel Silva <rui.silva at linaro.org>
>> ---
>> .../devicetree/bindings/media/imx7-csi.txt | 44 ++++++++++
>> .../bindings/media/imx7-mipi-csi2.txt | 82
>> +++++++++++++++++++
>> 2 files changed, 126 insertions(+)
>> create mode 100644
>> Documentation/devicetree/bindings/media/imx7-csi.txt
>> create mode 100644
>> Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt
>>
>> diff --git
>> a/Documentation/devicetree/bindings/media/imx7-csi.txt
>> b/Documentation/devicetree/bindings/media/imx7-csi.txt
>> new file mode 100644
>> index 000000000000..aab4f5d72390
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/media/imx7-csi.txt
>> @@ -0,0 +1,44 @@
>> +Freescale i.MX7 CMOS Sensor Interface
>> +=====================================
>> +
>> +csi node
>> +--------
>> +
>> +This is device node for the CMOS Sensor Interface (CSI) which
>> enables the chip
>> +to connect directly to external CMOS image sensors.
>> +
>> +Required properties:
>> +
>> +- compatible : "fsl,imx7-csi";
>> +- reg : base address and length of the register set
>> for the device;
>> +- interrupts : should contain CSI interrupt;
>> +- clocks : list of clock specifiers, see
>> +
>> Documentation/devicetree/bindings/clock/clock-bindings.txt for
>> details;
>> +- clock-names : must contain "axi", "mclk" and "dcic"
>> entries, matching
>> + entries in the clock property;
>> +
>> +The device node should contain one 'port' child node with one
>> child 'endpoint'
>
> "should" or "shall"?
>
>> +node, according to the bindings defined in
>> Documentation/devicetree/bindings/
>> +media/video-interfaces.txt. In the following example a remote
>> endpoint is a
>
> I wouldn't split the path as it breaks copy-paste; up to you.
>
>> +video multiplexer.
>> +
>> +example:
>> +
>> + csi: csi at 30710000 {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + compatible = "fsl,imx7-csi";
>> + reg = <0x30710000 0x10000>;
>> + interrupts = <GIC_SPI 7
>> IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&clks IMX7D_CLK_DUMMY>,
>> + <&clks
>> IMX7D_CSI_MCLK_ROOT_CLK>,
>> + <&clks
>> IMX7D_CLK_DUMMY>;
>> + clock-names = "axi", "mclk", "dcic";
>> +
>> + port {
>> + csi_from_csi_mux: endpoint {
>> + remote-endpoint =
>> <&csi_mux_to_csi>;
>> + };
>> + };
>> + };
>> diff --git
>> a/Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt
>> b/Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt
>> new file mode 100644
>> index 000000000000..7c5f20863724
>> --- /dev/null
>> +++
>> b/Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt
>> @@ -0,0 +1,82 @@
>> +Freescale i.MX7 Mipi CSI2
>> +=========================
>> +
>> +mipi_csi2 node
>> +--------------
>> +
>> +This is the device node for the MIPI CSI-2 receiver core in
>> i.MX7 SoC. It is
>> +compatible with previous version of Samsung D-phy.
>> +
>> +Required properties:
>> +
>> +- compatible : "fsl,imx7-mipi-csi2";
>> +- reg : base address and length of the register set
>> for the device;
>> +- interrupts : should contain MIPI CSIS interrupt;
>> +- clocks : list of clock specifiers, see
>> +
>> Documentation/devicetree/bindings/clock/clock-bindings.txt for
>> details;
>> +- clock-names : must contain "pclk", "wrap" and "phy"
>> entries, matching
>> + entries in the clock property;
>> +- power-domains : a phandle to the power domain, see
>> +
>> Documentation/devicetree/bindings/power/power_domain.txt for
>> details.
>> +- reset-names : should include following entry "mrst";
>> +- resets : a list of phandle, should contain reset
>> entry of
>> + reset-names;
>> +- phy-supply : from the generic phy bindings, a phandle to
>> a regulator that
>> + provides power to MIPI CSIS core;
>> +
>> +Optional properties:
>> +
>> +- clock-frequency : The IP's main (system bus) clock frequency
>> in Hz, default
>> + value when this property is not specified is
>> 166 MHz;
>> +- fsl,csis-hs-settle : differential receiver (HS-RX) settle
>> time;
>> +
>> +port node
>> +---------
>> +
>> +- reg : (required) can take the values 0 or 1,
>> where 0 is the
>> + related sink port and port 1 should be
>> the source one;
>
> Should and is -> shall?
>
> I think you should also elaborate whether or not the port (as
> well as the
> endpoint) nodes themselves are mandatory.
>
>> +
>> +endpoint node
>> +-------------
>> +
>> +- data-lanes : (required) an array specifying active
>> physical MIPI-CSI2
>> + data input lanes and their mapping to logical
>> lanes; the
>> + array's content is unused, only its length is
>> meaningful;
>
> If this is for port 0 only, please document that. Which values
> (length) are
> allowed?
>
>> +
>> +example:
>> +
>> + mipi_csi: mipi-csi at 30750000 {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + compatible = "fsl,imx7-mipi-csi2";
>> + reg = <0x30750000 0x10000>;
>> + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&clks IMX7D_IPG_ROOT_CLK>,
>> + <&clks
>> IMX7D_MIPI_CSI_ROOT_CLK>,
>> + <&clks
>> IMX7D_MIPI_DPHY_ROOT_CLK>;
>> + clock-names = "pclk", "wrap", "phy";
>> + clock-frequency = <166000000>;
>> + power-domains = <&pgc_mipi_phy>;
>> + phy-supply = <®_1p0d>;
>> + resets = <&src IMX7_RESET_MIPI_PHY_MRST>;
>> + reset-names = "mrst";
>> + fsl,csis-hs-settle = <3>;
>> +
>> + port at 0 {
>> + reg = <0>;
>> +
>> + mipi_from_sensor: endpoint {
>> + remote-endpoint =
>> <&ov2680_to_mipi>;
>> + data-lanes = <1>;
>> + };
>> + };
>> +
>> + port at 1 {
>> + reg = <1>;
>> +
>> + mipi_vc0_to_csi_mux: endpoint {
>> + remote-endpoint =
>> <&csi_mux_from_mipi_vc0>;
>> + };
>> + };
>> + };
More information about the devel
mailing list