[PATCH 5/7] staging:r8188eu: remove unused struct wifidirect_info and all corresponding code
Ivan Safonov
insafonov at gmail.com
Thu Jan 12 09:16:55 UTC 2017
wifidirect_info structure is unused.
Big amount of another definitions used only for wifidirect_info definition.
Remove all.
Signed-off-by: Ivan Safonov <insafonov at gmail.com>
---
drivers/staging/rtl8188eu/include/rtw_mlme.h | 177 ---------------------------
drivers/staging/rtl8188eu/include/wifi.h | 84 -------------
2 files changed, 261 deletions(-)
diff --git a/drivers/staging/rtl8188eu/include/rtw_mlme.h b/drivers/staging/rtl8188eu/include/rtw_mlme.h
index 6d03f94..7324a95 100644
--- a/drivers/staging/rtl8188eu/include/rtw_mlme.h
+++ b/drivers/staging/rtl8188eu/include/rtw_mlme.h
@@ -107,183 +107,6 @@ struct rt_link_detect {
* to Tx traffic. */
};
-struct profile_info {
- u8 ssidlen;
- u8 ssid[WLAN_SSID_MAXLEN];
- u8 peermac[ETH_ALEN];
-};
-
-struct tx_invite_req_info {
- u8 token;
- u8 benable;
- u8 go_ssid[WLAN_SSID_MAXLEN];
- u8 ssidlen;
- u8 go_bssid[ETH_ALEN];
- u8 peer_macaddr[ETH_ALEN];
- u8 operating_ch; /* This information will be set by using the
- * p2p_set op_ch=x */
- u8 peer_ch; /* The listen channel for peer P2P device */
-};
-
-struct tx_invite_resp_info {
- u8 token; /* Used to record the dialog token of p2p invitation
- * request frame. */
-};
-
-struct tx_provdisc_req_info {
- u16 wps_config_method_request; /* Used when sending the
- * provisioning request frame*/
- u16 peer_channel_num[2]; /* The channel number which the
- * receiver stands. */
- struct ndis_802_11_ssid ssid;
- u8 peerDevAddr[ETH_ALEN]; /* Peer device address */
- u8 peerIFAddr[ETH_ALEN]; /* Peer interface address */
- u8 benable; /* This provision discovery
- * request frame is trigger
- * to send or not */
-};
-
-/* When peer device issue prov_disc_req first, we should store the following
- * information */
-/* The UI must know this information to know which config method the
- * remote p2p device needs. */
-struct rx_provdisc_req_info {
- u8 peerDevAddr[ETH_ALEN]; /* Peer device address */
- u8 strconfig_method_desc_of_prov_disc_req[4]; /* description
- * for the config method located in the provisioning
- * discovery request frame. */
-};
-
-struct tx_nego_req_info {
- u16 peer_channel_num[2]; /* The channel number. */
- u8 peerDevAddr[ETH_ALEN]; /* Peer device address */
- u8 benable; /* This negotiation request frame is
- * trigger to send or not */
-};
-
-struct group_id_info {
- u8 go_device_addr[ETH_ALEN]; /* The GO's device address of
- * this P2P group */
- u8 ssid[WLAN_SSID_MAXLEN]; /* The SSID of this P2P group */
-};
-
-struct scan_limit_info {
- u8 scan_op_ch_only; /* When this flag is set, the driver
- * should only scan the op. channel */
- u8 operation_ch[2]; /* Store the op. chan of invitation */
-};
-
-struct wifidirect_info {
- struct adapter *padapter;
- struct timer_list find_phase_timer;
- struct timer_list restore_p2p_state_timer;
-
- /* Used to do the scanning. After confirming the peer is availalble,
- * the driver transmits the P2P frame to peer. */
- struct timer_list pre_tx_scan_timer;
- struct timer_list reset_ch_sitesurvey;
- struct timer_list reset_ch_sitesurvey2; /* Just for resetting the scan
- * limit function by using p2p nego */
- struct tx_provdisc_req_info tx_prov_disc_info;
- struct rx_provdisc_req_info rx_prov_disc_info;
- struct tx_invite_req_info invitereq_info;
- /* Store the profile information of persistent group */
- struct profile_info profileinfo[P2P_MAX_PERSISTENT_GROUP_NUM];
- struct tx_invite_resp_info inviteresp_info;
- struct tx_nego_req_info nego_req_info;
- /* Store the group id info when doing the group negot handshake. */
- struct group_id_info groupid_info;
- /* Used for get the limit scan channel from the Invitation procedure */
- struct scan_limit_info rx_invitereq_info;
- /* Used for get the limit scan chan from the P2P negotiation handshake*/
- struct scan_limit_info p2p_info;
- enum P2P_ROLE role;
- enum P2P_STATE pre_p2p_state;
- enum P2P_STATE p2p_state;
- /* The device address should be the mac address of this device. */
- u8 device_addr[ETH_ALEN];
- u8 interface_addr[ETH_ALEN];
- u8 social_chan[4];
- u8 listen_channel;
- u8 operating_channel;
- u8 listen_dwell; /* This value should be between 1 and 3 */
- u8 support_rate[8];
- u8 p2p_wildcard_ssid[P2P_WILDCARD_SSID_LEN];
- u8 intent; /* should only include the intent value. */
- u8 p2p_peer_interface_addr[ETH_ALEN];
- u8 p2p_peer_device_addr[ETH_ALEN];
- u8 peer_intent; /* Included the intent value and tie breaker value. */
- /* Device name for displaying on searching device screen */
- u8 device_name[WPS_MAX_DEVICE_NAME_LEN];
- u8 device_name_len;
- u8 profileindex; /* Used to point to the index of profileinfo array */
- u8 peer_operating_ch;
- u8 find_phase_state_exchange_cnt;
- /* The device password ID for group negotiation */
- u16 device_password_id_for_nego;
- u8 negotiation_dialog_token;
- /* SSID information for group negotitation */
- u8 nego_ssid[WLAN_SSID_MAXLEN];
- u8 nego_ssidlen;
- u8 p2p_group_ssid[WLAN_SSID_MAXLEN];
- u8 p2p_group_ssid_len;
- /* Flag to know if the persistent function should be supported or not.*/
- u8 persistent_supported;
- /* In the Sigma test, the Sigma will provide this enable from the
- * sta_set_p2p CAPI. */
- /* 0: disable */
- /* 1: enable */
- u8 session_available; /* Flag to set the WFD session available to
- * enable or disable "by Sigma" */
- /* In the Sigma test, the Sigma will disable the session available
- * by using the sta_preset CAPI. */
- /* 0: disable */
- /* 1: enable */
- u8 wfd_tdls_enable; /* Flag to enable or disable the TDLS by WFD Sigma*/
- /* 0: disable */
- /* 1: enable */
- u8 wfd_tdls_weaksec; /* Flag to enable or disable the weak security
- * function for TDLS by WFD Sigma */
- /* 0: disable */
- /* In this case, the driver can't issue the tdsl
- * setup request frame. */
- /* 1: enable */
- /* In this case, the driver can issue the tdls
- * setup request frame */
- /* even the current security is weak security. */
-
- /* This field will store the WPS value (PIN value or PBC) that UI had
- * got from the user. */
- enum P2P_WPSINFO ui_got_wps_info;
- u16 supported_wps_cm; /* This field describes the WPS config method
- * which this driver supported. */
- /* The value should be the combination of config
- * method defined in page104 of WPS v2.0 spec.*/
- /* This field will contain the length of body of P2P Channel List
- * attribute of group negotiation response frame. */
- uint channel_list_attr_len;
- /* This field will contain the body of P2P Channel List attribute of
- * group negotitation response frame. */
- /* We will use the channel_cnt and channel_list fields when constructing
- * the group negotiation confirm frame. */
- u8 channel_list_attr[100];
- enum P2P_PS_MODE p2p_ps_mode; /* indicate p2p ps mode */
- enum P2P_PS_STATE p2p_ps_state; /* indicate p2p ps state */
- u8 noa_index; /* Identifies and instance of Notice of Absence timing. */
- u8 ctwindow; /* Client traffic window. A period of time in TU after TBTT. */
- u8 opp_ps; /* opportunistic power save. */
- u8 noa_num; /* number of NoA descriptor in P2P IE. */
- u8 noa_count[P2P_MAX_NOA_NUM]; /* Count for owner, Type of client. */
- /* Max duration for owner, preferred or min acceptable duration for
- * client. */
- u32 noa_duration[P2P_MAX_NOA_NUM];
- /* Length of interval for owner, preferred or max acceptable interval
- * of client. */
- u32 noa_interval[P2P_MAX_NOA_NUM];
- /* schedule expressed in terms of the lower 4 bytes of the TSF timer. */
- u32 noa_start_time[P2P_MAX_NOA_NUM];
-};
-
struct mlme_priv {
spinlock_t lock;
int fw_state; /* shall we protect this variable? maybe not necessarily... */
diff --git a/drivers/staging/rtl8188eu/include/wifi.h b/drivers/staging/rtl8188eu/include/wifi.h
index 9e08e68..90c1027 100644
--- a/drivers/staging/rtl8188eu/include/wifi.h
+++ b/drivers/staging/rtl8188eu/include/wifi.h
@@ -23,7 +23,6 @@
#define WLAN_HDR_A4_LEN 30
#define WLAN_HDR_A3_QOS_LEN 26
#define WLAN_HDR_A4_QOS_LEN 32
-#define WLAN_SSID_MAXLEN 32
#define WLAN_DATA_MAXLEN 2312
#define WLAN_A3_PN_OFFSET 24
@@ -653,9 +652,6 @@ enum ht_cap_ampdu_factor {
#define WPS_ATTR_VENDOR_EXT 0x1049
#define WPS_ATTR_SELECTED_REGISTRAR 0x1041
-/* Value of WPS attribute "WPS_ATTR_DEVICE_NAME */
-#define WPS_MAX_DEVICE_NAME_LEN 32
-
/* Value of WPS Request Type Attribute */
#define WPS_REQ_TYPE_ENROLLEE_INFO_ONLY 0x00
#define WPS_REQ_TYPE_ENROLLEE_OPEN_8021X 0x01
@@ -804,13 +800,8 @@ enum ht_cap_ampdu_factor {
#define P2P_PRESENCE_RESPONSE 2
#define P2P_GO_DISC_REQUEST 3
-
-#define P2P_MAX_PERSISTENT_GROUP_NUM 10
-
#define P2P_PROVISIONING_SCAN_CNT 3
-#define P2P_WILDCARD_SSID_LEN 7
-
/* default value, used when: (1)p2p disabled or (2)p2p enabled
* but only do 1 scan phase */
#define P2P_FINDPHASE_EX_NONE 0
@@ -839,8 +830,6 @@ enum ht_cap_ampdu_factor {
#define P2P_RESET_SCAN_CH 25000
#define P2P_MAX_INTENT 15
-#define P2P_MAX_NOA_NUM 2
-
/* WPS Configuration Method */
#define WPS_CM_NONE 0x0000
#define WPS_CM_LABEL 0x0004
@@ -855,64 +844,6 @@ enum ht_cap_ampdu_factor {
#define WPS_CM_SW_DISPLAY_P 0x2008
#define WPS_CM_LCD_DISPLAY_P 0x4008
-enum P2P_ROLE {
- P2P_ROLE_DISABLE = 0,
- P2P_ROLE_DEVICE = 1,
- P2P_ROLE_CLIENT = 2,
- P2P_ROLE_GO = 3
-};
-
-enum P2P_STATE {
- P2P_STATE_NONE = 0, /* P2P disable */
- /* P2P had enabled and do nothing */
- P2P_STATE_IDLE = 1,
- P2P_STATE_LISTEN = 2, /* In pure listen state */
- P2P_STATE_SCAN = 3, /* In scan phase */
- /* In the listen state of find phase */
- P2P_STATE_FIND_PHASE_LISTEN = 4,
- /* In the search state of find phase */
- P2P_STATE_FIND_PHASE_SEARCH = 5,
- /* In P2P provisioning discovery */
- P2P_STATE_TX_PROVISION_DIS_REQ = 6,
- P2P_STATE_RX_PROVISION_DIS_RSP = 7,
- P2P_STATE_RX_PROVISION_DIS_REQ = 8,
- /* Doing the group owner negotiation handshake */
- P2P_STATE_GONEGO_ING = 9,
- /* finish the group negotiation handshake with success */
- P2P_STATE_GONEGO_OK = 10,
- /* finish the group negotiation handshake with failure */
- P2P_STATE_GONEGO_FAIL = 11,
- /* receiving the P2P Invitation request and match with the profile. */
- P2P_STATE_RECV_INVITE_REQ_MATCH = 12,
- /* Doing the P2P WPS */
- P2P_STATE_PROVISIONING_ING = 13,
- /* Finish the P2P WPS */
- P2P_STATE_PROVISIONING_DONE = 14,
- /* Transmit the P2P Invitation request */
- P2P_STATE_TX_INVITE_REQ = 15,
- /* Receiving the P2P Invitation response */
- P2P_STATE_RX_INVITE_RESP_OK = 16,
- /* receiving the P2P Invitation request and dismatch with the profile. */
- P2P_STATE_RECV_INVITE_REQ_DISMATCH = 17,
- /* receiving the P2P Invitation request and this wifi is GO. */
- P2P_STATE_RECV_INVITE_REQ_GO = 18,
- /* receiving the P2P Invitation request to join an existing P2P Group. */
- P2P_STATE_RECV_INVITE_REQ_JOIN = 19,
- /* receiving the P2P Invitation response with failure */
- P2P_STATE_RX_INVITE_RESP_FAIL = 20,
- /* receiving p2p negotiation response with information is not available */
- P2P_STATE_RX_INFOR_NOREADY = 21,
- /* sending p2p negotiation response with information is not available */
- P2P_STATE_TX_INFOR_NOREADY = 22,
-};
-
-enum P2P_WPSINFO {
- P2P_NO_WPSINFO = 0,
- P2P_GOT_WPSINFO_PEER_DISPLAY_PIN = 1,
- P2P_GOT_WPSINFO_SELF_DISPLAY_PIN = 2,
- P2P_GOT_WPSINFO_PBC = 3,
-};
-
#define P2P_PRIVATE_IOCTL_SET_LEN 64
enum P2P_PROTO_WK_ID {
@@ -925,21 +856,6 @@ enum P2P_PROTO_WK_ID {
P2P_RO_CH_WK = 6,
};
-enum P2P_PS_STATE {
- P2P_PS_DISABLE = 0,
- P2P_PS_ENABLE = 1,
- P2P_PS_SCAN = 2,
- P2P_PS_SCAN_DONE = 3,
- P2P_PS_ALLSTASLEEP = 4, /* for P2P GO */
-};
-
-enum P2P_PS_MODE {
- P2P_PS_NONE = 0,
- P2P_PS_CTWINDOW = 1,
- P2P_PS_NOA = 2,
- P2P_PS_MIX = 3, /* CTWindow and NoA */
-};
-
/* =====================WFD Section===================== */
/* For Wi-Fi Display */
#define WFD_ATTR_DEVICE_INFO 0x00
--
2.10.2
More information about the devel
mailing list