[PATCH v4 01/36] [media] dt-bindings: Add bindings for i.MX media driver

Rob Herring robh at kernel.org
Mon Feb 27 14:38:23 UTC 2017


On Wed, Feb 15, 2017 at 06:19:03PM -0800, Steve Longerbeam wrote:
> Add bindings documentation for the i.MX media driver.
> 
> Signed-off-by: Steve Longerbeam <steve_longerbeam at mentor.com>
> ---
>  Documentation/devicetree/bindings/media/imx.txt | 66 +++++++++++++++++++++++++
>  1 file changed, 66 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/imx.txt
> 
> diff --git a/Documentation/devicetree/bindings/media/imx.txt b/Documentation/devicetree/bindings/media/imx.txt
> new file mode 100644
> index 0000000..fd5af50
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/imx.txt
> @@ -0,0 +1,66 @@
> +Freescale i.MX Media Video Device
> +=================================
> +
> +Video Media Controller node
> +---------------------------
> +
> +This is the media controller node for video capture support. It is a
> +virtual device that lists the camera serial interface nodes that the
> +media device will control.
> +
> +Required properties:
> +- compatible : "fsl,imx-capture-subsystem";
> +- ports      : Should contain a list of phandles pointing to camera
> +		sensor interface ports of IPU devices
> +
> +example:
> +
> +capture-subsystem {
> +	compatible = "fsl,capture-subsystem";
> +	ports = <&ipu1_csi0>, <&ipu1_csi1>;
> +};
> +
> +fim child node
> +--------------
> +
> +This is an optional child node of the ipu_csi port nodes. If present and
> +available, it enables the Frame Interval Monitor. Its properties can be
> +used to modify the method in which the FIM measures frame intervals.
> +Refer to Documentation/media/v4l-drivers/imx.rst for more info on the
> +Frame Interval Monitor.

This should have a compatible string.

> +
> +Optional properties:
> +- fsl,input-capture-channel: an input capture channel and channel flags,
> +			     specified as <chan flags>. The channel number
> +			     must be 0 or 1. The flags can be
> +			     IRQ_TYPE_EDGE_RISING, IRQ_TYPE_EDGE_FALLING, or
> +			     IRQ_TYPE_EDGE_BOTH, and specify which input
> +			     capture signal edge will trigger the input
> +			     capture event. If an input capture channel is
> +			     specified, the FIM will use this method to
> +			     measure frame intervals instead of via the EOF
> +			     interrupt. The input capture method is much
> +			     preferred over EOF as it is not subject to
> +			     interrupt latency errors. However it requires
> +			     routing the VSYNC or FIELD output signals of
> +			     the camera sensor to one of the i.MX input
> +			     capture pads (SD1_DAT0, SD1_DAT1), which also
> +			     gives up support for SD1.
> +
> +
> +mipi_csi2 node
> +--------------
> +
> +This is the device node for the MIPI CSI-2 Receiver, required for MIPI
> +CSI-2 sensors.
> +
> +Required properties:
> +- compatible	: "fsl,imx6-mipi-csi2", "snps,dw-mipi-csi2";
> +- reg           : physical base address and length of the register set;
> +- clocks	: the MIPI CSI-2 receiver requires three clocks: hsi_tx
> +                  (the DPHY clock), video_27m, and eim_podf;
> +- clock-names	: must contain "dphy", "cfg", "pix";

Don't you need ports to describe the sensor and IPU connections?

> +
> +Optional properties:
> +- interrupts	: must contain two level-triggered interrupts,
> +                  in order: 100 and 101;
> -- 
> 2.7.4
> 


More information about the devel mailing list