[PATCH v4 00/36] i.MX Media Driver

Philipp Zabel p.zabel at pengutronix.de
Fri Feb 17 11:21:52 UTC 2017


On Fri, 2017-02-17 at 10:56 +0000, Russell King - ARM Linux wrote:
> On Fri, Feb 17, 2017 at 11:39:11AM +0100, Philipp Zabel wrote:
> > On Thu, 2017-02-16 at 22:57 +0000, Russell King - ARM Linux wrote:
> > > On Thu, Feb 16, 2017 at 02:27:41PM -0800, Steve Longerbeam wrote:
> > > > 
> > > > 
> > > > On 02/16/2017 02:20 PM, Russell King - ARM Linux wrote:
> > > > >On Wed, Feb 15, 2017 at 06:19:02PM -0800, Steve Longerbeam wrote:
> > > > >>In version 4:
> > > > >
> > > > >With this version, I get:
> > > > >
> > > > >[28762.892053] imx6-mipi-csi2: LP-11 timeout, phy_state = 0x00000000
> > > > >[28762.899409] ipu1_csi0: pipeline_set_stream failed with -110
> > > > >
> > > > 
> > > > Right, in the imx219, on exit from s_power(), the clock and data lanes
> > > > must be placed in the LP-11 state. This has been done in the ov5640 and
> > > > tc358743 subdevs.
> > > 
> > > The only way to do that is to enable streaming from the sensor, wait
> > > an initialisation time, and then disable streaming, and wait for the
> > > current line to finish.  There is _no_ other way to get the sensor to
> > > place its clock and data lines into LP-11 state.
> > 
> > I thought going through LP-11 is part of the D-PHY transmitter
> > initialization, during the LP->HS wakeup sequence. But then I have no
> > access to MIPI specs.
> 
> The D-PHY transmitter initialisation *only* happens as part of the
> wake-up from standby to streaming mode.  That is because Sony expect
> that you program the sensor, and then when you switch it to streaming
> mode, it computes the D-PHY parameters from the PLL, input clock rate
> (you have to tell it the clock rate in 1/256 MHz units), number of
> lanes, and other parameters.
> 
> It is possible to program the D-PHY parameters manually, but that
> doesn't change the above sequence in any way (it just avoids the
> chip computing the values, it doesn't result in any change of
> behaviour on the bus.)
>
> The IMX219 specifications are clear: the clock and data lines are
> held low (LP-00 state) after releasing the hardware enable signal.
> There's a period of chip initialisation, and then you can access the
> I2C bus and configure it.  There's a further period of initialisation
> where charge pumps are getting to their operating state.  Then, you
> set the streaming bit, and a load more initialisation happens before
> the CSI bus enters LP-11 state and the first frame pops out.  When
> entering standby, the last frame is completed, and then the CSI bus
> enters LP-11 state.

How about firing off a thread in imx6-mipi-csi2 prepare_stream that
spins on the LP-11 check and then continues with the receiver D-PHY
initialization once the condition is met? I think we should have at
least 100 us to do this, but maybe the IMX219 can be programmed to stay
in LP-11 for a longer time.

> SMIA are slightly different - mostly following what I've said above,
> but the clock and data lines are tristated after releasing the
> xshutdown signal, and they remain tristated until the clock line
> starts toggling before the first frame appears.  There appears to
> be no point that the clock line enters LP-11 state before it starts
> toggling.  When entering standby, the last frame is completed, and
> the CSI bus enters tristate mode (so floating.)  There is no way to
> get these sensors into LP-11 state.

I have no idea what to do about those.

regards
Philipp



More information about the devel mailing list