[PATCH 2/5] staging: wilc1000: remove the warnings on multiple blank line uses.
Sunghoon Cho
ywhsbliss at gmail.com
Wed Jun 17 07:28:52 UTC 2015
This patch removes the warnings reported by checkpatch.pl regarding
the multiple blank line.
Signed-off-by: Sunghoon Cho <ywhsbliss at gmail.com>
---
drivers/staging/wilc1000/wilc_wlan_if.h | 12 ------------
1 file changed, 12 deletions(-)
diff --git a/drivers/staging/wilc1000/wilc_wlan_if.h b/drivers/staging/wilc1000/wilc_wlan_if.h
index c7143cd..33d70c6 100644
--- a/drivers/staging/wilc1000/wilc_wlan_if.h
+++ b/drivers/staging/wilc1000/wilc_wlan_if.h
@@ -3,7 +3,6 @@
* Module Name: wilc_wlan_if.h
*/
-
#ifndef WILC_WLAN_IF_H
#define WILC_WLAN_IF_H
@@ -15,11 +14,9 @@
/* #define WILC_FULLY_HOSTING_AP */
/* #define USE_OLD_SPI_SW */
-
#include "wilc_type.h"
#include "linux_wlan_common.h"
-
/* Debug Flags */
#define N_INIT 0x00000001
@@ -34,7 +31,6 @@
#define HIF_SPI (1 << 0)
#define HIF_SDIO_GPIO_IRQ (1 << 2)
-
/* Tx/Rx Buffer Size Defines */
#define CE_TX_BUFFER_SIZE (64 * 1024)
@@ -181,7 +177,6 @@ struct tx_complete_data {
struct sk_buff *skb;
};
-
typedef void (*wilc_tx_complete_func_t)(void *, int);
#define WILC_TX_ERR_NO_BUF (-2)
@@ -423,7 +418,6 @@ typedef enum {
typedef enum {
WID_NIL = 0xffff,
-
/*
* BSS Type
* --------------------------------------------------------------
@@ -874,7 +868,6 @@ typedef enum {
*/
WID_11N_TXOP_PROT_DISABLE = 0x00B0,
-
WID_TX_POWER_LEVEL_11N = 0x00B1,
/* Custom Character WID list */
@@ -954,7 +947,6 @@ typedef enum {
WID_MEMORY_ACCESS_32BIT = 0x201F,
WID_RF_REG_VAL = 0x2021,
-
/* NMAC Integer WID list */
WID_11N_PHY_ACTIVE_REG_VAL = 0x2080,
@@ -1017,8 +1009,6 @@ typedef enum {
/* BugID 4951: WID toset IP address in firmware */
WID_IP_ADDRESS = 0x3999,
-
-
/* Custom String WID list */
/* EMAC Binary WID list */
@@ -1033,7 +1023,6 @@ typedef enum {
/* NMAC Binary WID list */
WID_11N_AUTORATE_TABLE = 0x4080,
-
/* Added here by Amr - BugID 4134 */
WID_SCAN_CHANNEL_LIST = 0x4084,
@@ -1060,5 +1049,4 @@ void wilc_bus_set_max_speed(void);
void wilc_bus_set_default_speed(void);
uint32_t wilc_get_chipid(uint8_t update);
-
#endif
--
1.9.1
More information about the devel
mailing list