[PATCH v3 2/9] mfd: rtsx: place register address and values togather
micky_ching at realsil.com.cn
micky_ching at realsil.com.cn
Wed Feb 25 05:50:09 UTC 2015
From: Micky Ching <micky_ching at realsil.com.cn>
It is more readable to place register address and values define
togather. The values define add two leading space indicate belong
to the register address defined above.
Signed-off-by: Micky Ching <micky_ching at realsil.com.cn>
Acked-by: Lee Jones <lee.jones at linaro.org>
---
include/linux/mfd/rtsx_pci.h | 836 +++++++++++++++++++------------------------
1 file changed, 369 insertions(+), 467 deletions(-)
diff --git a/include/linux/mfd/rtsx_pci.h b/include/linux/mfd/rtsx_pci.h
index a9c2a14..e81f2bb 100644
--- a/include/linux/mfd/rtsx_pci.h
+++ b/include/linux/mfd/rtsx_pci.h
@@ -28,74 +28,72 @@
#define MAX_RW_REG_CNT 1024
-/* PCI Operation Register Address */
#define RTSX_HCBAR 0x00
#define RTSX_HCBCTLR 0x04
+#define STOP_CMD (0x01 << 28)
+#define READ_REG_CMD 0
+#define WRITE_REG_CMD 1
+#define CHECK_REG_CMD 2
+
#define RTSX_HDBAR 0x08
+#define SG_INT 0x04
+#define SG_END 0x02
+#define SG_VALID 0x01
+#define SG_NO_OP 0x00
+#define SG_TRANS_DATA (0x02 << 4)
+#define SG_LINK_DESC (0x03 << 4)
#define RTSX_HDBCTLR 0x0C
+#define SDMA_MODE 0x00
+#define ADMA_MODE (0x02 << 26)
+#define STOP_DMA (0x01 << 28)
+#define TRIG_DMA (0x01 << 31)
+
#define RTSX_HAIMR 0x10
-#define RTSX_BIPR 0x14
-#define RTSX_BIER 0x18
+#define HAIMR_TRANS_START (0x01 << 31)
+#define HAIMR_READ 0x00
+#define HAIMR_WRITE (0x01 << 30)
+#define HAIMR_READ_START (HAIMR_TRANS_START | HAIMR_READ)
+#define HAIMR_WRITE_START (HAIMR_TRANS_START | HAIMR_WRITE)
+#define HAIMR_TRANS_END (HAIMR_TRANS_START)
-/* Host command buffer control register */
-#define STOP_CMD (0x01 << 28)
-
-/* Host data buffer control register */
-#define SDMA_MODE 0x00
-#define ADMA_MODE (0x02 << 26)
-#define STOP_DMA (0x01 << 28)
-#define TRIG_DMA (0x01 << 31)
-
-/* Host access internal memory register */
-#define HAIMR_TRANS_START (0x01 << 31)
-#define HAIMR_READ 0x00
-#define HAIMR_WRITE (0x01 << 30)
-#define HAIMR_READ_START (HAIMR_TRANS_START | HAIMR_READ)
-#define HAIMR_WRITE_START (HAIMR_TRANS_START | HAIMR_WRITE)
-#define HAIMR_TRANS_END (HAIMR_TRANS_START)
-
-/* Bus interrupt pending register */
-#define CMD_DONE_INT (1 << 31)
-#define DATA_DONE_INT (1 << 30)
-#define TRANS_OK_INT (1 << 29)
-#define TRANS_FAIL_INT (1 << 28)
-#define XD_INT (1 << 27)
-#define MS_INT (1 << 26)
-#define SD_INT (1 << 25)
-#define GPIO0_INT (1 << 24)
-#define OC_INT (1 << 23)
-#define SD_WRITE_PROTECT (1 << 19)
-#define XD_EXIST (1 << 18)
-#define MS_EXIST (1 << 17)
-#define SD_EXIST (1 << 16)
-#define DELINK_INT GPIO0_INT
-#define MS_OC_INT (1 << 23)
-#define SD_OC_INT (1 << 22)
+#define RTSX_BIPR 0x14
+#define CMD_DONE_INT (1 << 31)
+#define DATA_DONE_INT (1 << 30)
+#define TRANS_OK_INT (1 << 29)
+#define TRANS_FAIL_INT (1 << 28)
+#define XD_INT (1 << 27)
+#define MS_INT (1 << 26)
+#define SD_INT (1 << 25)
+#define GPIO0_INT (1 << 24)
+#define OC_INT (1 << 23)
+#define SD_WRITE_PROTECT (1 << 19)
+#define XD_EXIST (1 << 18)
+#define MS_EXIST (1 << 17)
+#define SD_EXIST (1 << 16)
+#define DELINK_INT GPIO0_INT
+#define MS_OC_INT (1 << 23)
+#define SD_OC_INT (1 << 22)
#define CARD_INT (XD_INT | MS_INT | SD_INT)
#define NEED_COMPLETE_INT (DATA_DONE_INT | TRANS_OK_INT | TRANS_FAIL_INT)
#define RTSX_INT (CMD_DONE_INT | NEED_COMPLETE_INT | \
CARD_INT | GPIO0_INT | OC_INT)
-
#define CARD_EXIST (XD_EXIST | MS_EXIST | SD_EXIST)
-/* Bus interrupt enable register */
-#define CMD_DONE_INT_EN (1 << 31)
-#define DATA_DONE_INT_EN (1 << 30)
-#define TRANS_OK_INT_EN (1 << 29)
-#define TRANS_FAIL_INT_EN (1 << 28)
-#define XD_INT_EN (1 << 27)
-#define MS_INT_EN (1 << 26)
-#define SD_INT_EN (1 << 25)
-#define GPIO0_INT_EN (1 << 24)
-#define OC_INT_EN (1 << 23)
-#define DELINK_INT_EN GPIO0_INT_EN
-#define MS_OC_INT_EN (1 << 23)
-#define SD_OC_INT_EN (1 << 22)
-
-#define READ_REG_CMD 0
-#define WRITE_REG_CMD 1
-#define CHECK_REG_CMD 2
+#define RTSX_BIER 0x18
+#define CMD_DONE_INT_EN (1 << 31)
+#define DATA_DONE_INT_EN (1 << 30)
+#define TRANS_OK_INT_EN (1 << 29)
+#define TRANS_FAIL_INT_EN (1 << 28)
+#define XD_INT_EN (1 << 27)
+#define MS_INT_EN (1 << 26)
+#define SD_INT_EN (1 << 25)
+#define GPIO0_INT_EN (1 << 24)
+#define OC_INT_EN (1 << 23)
+#define DELINK_INT_EN GPIO0_INT_EN
+#define MS_OC_INT_EN (1 << 23)
+#define SD_OC_INT_EN (1 << 22)
+
/*
* macros for easy use
@@ -125,423 +123,68 @@
#define rtsx_pci_write_config_dword(pcr, where, val) \
pci_write_config_dword((pcr)->pci, where, val)
-#define STATE_TRANS_NONE 0
-#define STATE_TRANS_CMD 1
-#define STATE_TRANS_BUF 2
-#define STATE_TRANS_SG 3
-
-#define TRANS_NOT_READY 0
-#define TRANS_RESULT_OK 1
-#define TRANS_RESULT_FAIL 2
-#define TRANS_NO_DEVICE 3
-
-#define RTSX_RESV_BUF_LEN 4096
-#define HOST_CMDS_BUF_LEN 1024
-#define HOST_SG_TBL_BUF_LEN (RTSX_RESV_BUF_LEN - HOST_CMDS_BUF_LEN)
-#define HOST_SG_TBL_ITEMS (HOST_SG_TBL_BUF_LEN / 8)
-#define MAX_SG_ITEM_LEN 0x80000
-
-#define HOST_TO_DEVICE 0
-#define DEVICE_TO_HOST 1
-
-#define RTSX_PHASE_MAX 32
-#define RX_TUNING_CNT 3
-
-/* SG descriptor */
-#define SG_INT 0x04
-#define SG_END 0x02
-#define SG_VALID 0x01
-
-#define SG_NO_OP 0x00
-#define SG_TRANS_DATA (0x02 << 4)
-#define SG_LINK_DESC (0x03 << 4)
-
-/* Output voltage */
-#define OUTPUT_3V3 0
-#define OUTPUT_1V8 1
-
-/* Card Clock Enable Register */
-#define SD_CLK_EN 0x04
-#define MS_CLK_EN 0x08
-
-/* Card Select Register */
-#define SD_MOD_SEL 2
-#define MS_MOD_SEL 3
-
-/* Card Output Enable Register */
-#define SD_OUTPUT_EN 0x04
-#define MS_OUTPUT_EN 0x08
-
-/* CARD_SHARE_MODE */
-#define CARD_SHARE_MASK 0x0F
-#define CARD_SHARE_MULTI_LUN 0x00
-#define CARD_SHARE_NORMAL 0x00
-#define CARD_SHARE_48_SD 0x04
-#define CARD_SHARE_48_MS 0x08
-/* CARD_SHARE_MODE for barossa */
-#define CARD_SHARE_BAROSSA_SD 0x01
-#define CARD_SHARE_BAROSSA_MS 0x02
-
-/* CARD_DRIVE_SEL */
-#define MS_DRIVE_8mA (0x01 << 6)
-#define MMC_DRIVE_8mA (0x01 << 4)
-#define XD_DRIVE_8mA (0x01 << 2)
-#define GPIO_DRIVE_8mA 0x01
-#define RTS5209_CARD_DRIVE_DEFAULT (MS_DRIVE_8mA | MMC_DRIVE_8mA |\
- XD_DRIVE_8mA | GPIO_DRIVE_8mA)
-#define RTL8411_CARD_DRIVE_DEFAULT (MS_DRIVE_8mA | MMC_DRIVE_8mA |\
- XD_DRIVE_8mA)
-#define RTSX_CARD_DRIVE_DEFAULT (MS_DRIVE_8mA | GPIO_DRIVE_8mA)
+#define STATE_TRANS_NONE 0
+#define STATE_TRANS_CMD 1
+#define STATE_TRANS_BUF 2
+#define STATE_TRANS_SG 3
-/* SD30_DRIVE_SEL */
-#define DRIVER_TYPE_A 0x05
-#define DRIVER_TYPE_B 0x03
-#define DRIVER_TYPE_C 0x02
-#define DRIVER_TYPE_D 0x01
-#define CFG_DRIVER_TYPE_A 0x02
-#define CFG_DRIVER_TYPE_B 0x03
-#define CFG_DRIVER_TYPE_C 0x01
-#define CFG_DRIVER_TYPE_D 0x00
-
-/* FPDCTL */
-#define SSC_POWER_DOWN 0x01
-#define SD_OC_POWER_DOWN 0x02
-#define ALL_POWER_DOWN 0x07
-#define OC_POWER_DOWN 0x06
-
-/* CLK_CTL */
-#define CHANGE_CLK 0x01
-
-/* LDO_CTL */
-#define BPP_ASIC_1V7 0x00
-#define BPP_ASIC_1V8 0x01
-#define BPP_ASIC_1V9 0x02
-#define BPP_ASIC_2V0 0x03
-#define BPP_ASIC_2V7 0x04
-#define BPP_ASIC_2V8 0x05
-#define BPP_ASIC_3V2 0x06
-#define BPP_ASIC_3V3 0x07
-#define BPP_REG_TUNED18 0x07
-#define BPP_TUNED18_SHIFT_8402 5
-#define BPP_TUNED18_SHIFT_8411 4
-#define BPP_PAD_MASK 0x04
-#define BPP_PAD_3V3 0x04
-#define BPP_PAD_1V8 0x00
-#define BPP_LDO_POWB 0x03
-#define BPP_LDO_ON 0x00
-#define BPP_LDO_SUSPEND 0x02
-#define BPP_LDO_OFF 0x03
-
-/* CD_PAD_CTL */
-#define CD_DISABLE_MASK 0x07
-#define MS_CD_DISABLE 0x04
-#define SD_CD_DISABLE 0x02
-#define XD_CD_DISABLE 0x01
-#define CD_DISABLE 0x07
-#define CD_ENABLE 0x00
-#define MS_CD_EN_ONLY 0x03
-#define SD_CD_EN_ONLY 0x05
-#define XD_CD_EN_ONLY 0x06
-#define FORCE_CD_LOW_MASK 0x38
-#define FORCE_CD_XD_LOW 0x08
-#define FORCE_CD_SD_LOW 0x10
-#define FORCE_CD_MS_LOW 0x20
-#define CD_AUTO_DISABLE 0x40
-
-/* SD_STAT1 */
-#define SD_CRC7_ERR 0x80
-#define SD_CRC16_ERR 0x40
-#define SD_CRC_WRITE_ERR 0x20
-#define SD_CRC_WRITE_ERR_MASK 0x1C
-#define GET_CRC_TIME_OUT 0x02
-#define SD_TUNING_COMPARE_ERR 0x01
-
-/* SD_STAT2 */
-#define SD_RSP_80CLK_TIMEOUT 0x01
-
-/* SD_BUS_STAT */
-#define SD_CLK_TOGGLE_EN 0x80
-#define SD_CLK_FORCE_STOP 0x40
-#define SD_DAT3_STATUS 0x10
-#define SD_DAT2_STATUS 0x08
-#define SD_DAT1_STATUS 0x04
-#define SD_DAT0_STATUS 0x02
-#define SD_CMD_STATUS 0x01
-
-/* SD_PAD_CTL */
-#define SD_IO_USING_1V8 0x80
-#define SD_IO_USING_3V3 0x7F
-#define TYPE_A_DRIVING 0x00
-#define TYPE_B_DRIVING 0x01
-#define TYPE_C_DRIVING 0x02
-#define TYPE_D_DRIVING 0x03
-
-/* SD_SAMPLE_POINT_CTL */
-#define DDR_FIX_RX_DAT 0x00
-#define DDR_VAR_RX_DAT 0x80
-#define DDR_FIX_RX_DAT_EDGE 0x00
-#define DDR_FIX_RX_DAT_14_DELAY 0x40
-#define DDR_FIX_RX_CMD 0x00
-#define DDR_VAR_RX_CMD 0x20
-#define DDR_FIX_RX_CMD_POS_EDGE 0x00
-#define DDR_FIX_RX_CMD_14_DELAY 0x10
-#define SD20_RX_POS_EDGE 0x00
-#define SD20_RX_14_DELAY 0x08
-#define SD20_RX_SEL_MASK 0x08
+#define TRANS_NOT_READY 0
+#define TRANS_RESULT_OK 1
+#define TRANS_RESULT_FAIL 2
+#define TRANS_NO_DEVICE 3
-/* SD_PUSH_POINT_CTL */
-#define DDR_FIX_TX_CMD_DAT 0x00
-#define DDR_VAR_TX_CMD_DAT 0x80
-#define DDR_FIX_TX_DAT_14_TSU 0x00
-#define DDR_FIX_TX_DAT_12_TSU 0x40
-#define DDR_FIX_TX_CMD_NEG_EDGE 0x00
-#define DDR_FIX_TX_CMD_14_AHEAD 0x20
-#define SD20_TX_NEG_EDGE 0x00
-#define SD20_TX_14_AHEAD 0x10
-#define SD20_TX_SEL_MASK 0x10
-#define DDR_VAR_SDCLK_POL_SWAP 0x01
-
-/* SD_TRANSFER */
-#define SD_TRANSFER_START 0x80
-#define SD_TRANSFER_END 0x40
-#define SD_STAT_IDLE 0x20
-#define SD_TRANSFER_ERR 0x10
-/* SD Transfer Mode definition */
-#define SD_TM_NORMAL_WRITE 0x00
-#define SD_TM_AUTO_WRITE_3 0x01
-#define SD_TM_AUTO_WRITE_4 0x02
-#define SD_TM_AUTO_READ_3 0x05
-#define SD_TM_AUTO_READ_4 0x06
-#define SD_TM_CMD_RSP 0x08
-#define SD_TM_AUTO_WRITE_1 0x09
-#define SD_TM_AUTO_WRITE_2 0x0A
-#define SD_TM_NORMAL_READ 0x0C
-#define SD_TM_AUTO_READ_1 0x0D
-#define SD_TM_AUTO_READ_2 0x0E
-#define SD_TM_AUTO_TUNING 0x0F
-
-/* SD_VPTX_CTL / SD_VPRX_CTL */
-#define PHASE_CHANGE 0x80
-#define PHASE_NOT_RESET 0x40
-
-/* SD_DCMPS_TX_CTL / SD_DCMPS_RX_CTL */
-#define DCMPS_CHANGE 0x80
-#define DCMPS_CHANGE_DONE 0x40
-#define DCMPS_ERROR 0x20
-#define DCMPS_CURRENT_PHASE 0x1F
-
-/* SD Configure 1 Register */
-#define SD_CLK_DIVIDE_0 0x00
-#define SD_CLK_DIVIDE_256 0xC0
-#define SD_CLK_DIVIDE_128 0x80
-#define SD_BUS_WIDTH_1BIT 0x00
-#define SD_BUS_WIDTH_4BIT 0x01
-#define SD_BUS_WIDTH_8BIT 0x02
-#define SD_ASYNC_FIFO_NOT_RST 0x10
-#define SD_20_MODE 0x00
-#define SD_DDR_MODE 0x04
-#define SD_30_MODE 0x08
-
-#define SD_CLK_DIVIDE_MASK 0xC0
-
-/* SD_CMD_STATE */
-#define SD_CMD_IDLE 0x80
-
-/* SD_DATA_STATE */
-#define SD_DATA_IDLE 0x80
-
-/* DCM_DRP_CTL */
-#define DCM_RESET 0x08
-#define DCM_LOCKED 0x04
-#define DCM_208M 0x00
-#define DCM_TX 0x01
-#define DCM_RX 0x02
-
-/* DCM_DRP_TRIG */
-#define DRP_START 0x80
-#define DRP_DONE 0x40
-
-/* DCM_DRP_CFG */
-#define DRP_WRITE 0x80
-#define DRP_READ 0x00
-#define DCM_WRITE_ADDRESS_50 0x50
-#define DCM_WRITE_ADDRESS_51 0x51
-#define DCM_READ_ADDRESS_00 0x00
-#define DCM_READ_ADDRESS_51 0x51
-
-/* IRQSTAT0 */
-#define DMA_DONE_INT 0x80
-#define SUSPEND_INT 0x40
-#define LINK_RDY_INT 0x20
-#define LINK_DOWN_INT 0x10
-
-/* DMACTL */
-#define DMA_RST 0x80
-#define DMA_BUSY 0x04
-#define DMA_DIR_TO_CARD 0x00
-#define DMA_DIR_FROM_CARD 0x02
-#define DMA_EN 0x01
-#define DMA_128 (0 << 4)
-#define DMA_256 (1 << 4)
-#define DMA_512 (2 << 4)
-#define DMA_1024 (3 << 4)
-#define DMA_PACK_SIZE_MASK 0x30
-
-/* SSC_CTL1 */
-#define SSC_RSTB 0x80
-#define SSC_8X_EN 0x40
-#define SSC_FIX_FRAC 0x20
-#define SSC_SEL_1M 0x00
-#define SSC_SEL_2M 0x08
-#define SSC_SEL_4M 0x10
-#define SSC_SEL_8M 0x18
-
-/* SSC_CTL2 */
-#define SSC_DEPTH_MASK 0x07
-#define SSC_DEPTH_DISALBE 0x00
-#define SSC_DEPTH_4M 0x01
-#define SSC_DEPTH_2M 0x02
-#define SSC_DEPTH_1M 0x03
-#define SSC_DEPTH_500K 0x04
-#define SSC_DEPTH_250K 0x05
-
-/* System Clock Control Register */
-#define CLK_LOW_FREQ 0x01
-
-/* System Clock Divider Register */
-#define CLK_DIV_1 0x01
-#define CLK_DIV_2 0x02
-#define CLK_DIV_4 0x03
-#define CLK_DIV_8 0x04
-
-/* MS_CFG */
-#define SAMPLE_TIME_RISING 0x00
-#define SAMPLE_TIME_FALLING 0x80
-#define PUSH_TIME_DEFAULT 0x00
-#define PUSH_TIME_ODD 0x40
-#define NO_EXTEND_TOGGLE 0x00
-#define EXTEND_TOGGLE_CHK 0x20
-#define MS_BUS_WIDTH_1 0x00
-#define MS_BUS_WIDTH_4 0x10
-#define MS_BUS_WIDTH_8 0x18
-#define MS_2K_SECTOR_MODE 0x04
-#define MS_512_SECTOR_MODE 0x00
-#define MS_TOGGLE_TIMEOUT_EN 0x00
-#define MS_TOGGLE_TIMEOUT_DISEN 0x01
-#define MS_NO_CHECK_INT 0x02
+#define RTSX_RESV_BUF_LEN 4096
+#define HOST_CMDS_BUF_LEN 1024
+#define HOST_SG_TBL_BUF_LEN (RTSX_RESV_BUF_LEN - HOST_CMDS_BUF_LEN)
+#define HOST_SG_TBL_ITEMS (HOST_SG_TBL_BUF_LEN / 8)
+#define MAX_SG_ITEM_LEN 0x80000
+#define HOST_TO_DEVICE 0
+#define DEVICE_TO_HOST 1
+
+#define OUTPUT_3V3 0
+#define OUTPUT_1V8 1
-/* MS_TRANS_CFG */
-#define WAIT_INT 0x80
-#define NO_WAIT_INT 0x00
-#define NO_AUTO_READ_INT_REG 0x00
-#define AUTO_READ_INT_REG 0x40
-#define MS_CRC16_ERR 0x20
-#define MS_RDY_TIMEOUT 0x10
-#define MS_INT_CMDNK 0x08
-#define MS_INT_BREQ 0x04
-#define MS_INT_ERR 0x02
-#define MS_INT_CED 0x01
-
-/* MS_TRANSFER */
-#define MS_TRANSFER_START 0x80
-#define MS_TRANSFER_END 0x40
-#define MS_TRANSFER_ERR 0x20
-#define MS_BS_STATE 0x10
-#define MS_TM_READ_BYTES 0x00
-#define MS_TM_NORMAL_READ 0x01
-#define MS_TM_WRITE_BYTES 0x04
-#define MS_TM_NORMAL_WRITE 0x05
-#define MS_TM_AUTO_READ 0x08
-#define MS_TM_AUTO_WRITE 0x0C
-
-/* SD Configure 2 Register */
-#define SD_CALCULATE_CRC7 0x00
-#define SD_NO_CALCULATE_CRC7 0x80
-#define SD_CHECK_CRC16 0x00
-#define SD_NO_CHECK_CRC16 0x40
-#define SD_NO_CHECK_WAIT_CRC_TO 0x20
-#define SD_WAIT_BUSY_END 0x08
-#define SD_NO_WAIT_BUSY_END 0x00
-#define SD_CHECK_CRC7 0x00
-#define SD_NO_CHECK_CRC7 0x04
-#define SD_RSP_LEN_0 0x00
-#define SD_RSP_LEN_6 0x01
-#define SD_RSP_LEN_17 0x02
-/* SD/MMC Response Type Definition */
-#define SD_RSP_TYPE_R0 0x04
-#define SD_RSP_TYPE_R1 0x01
-#define SD_RSP_TYPE_R1b 0x09
-#define SD_RSP_TYPE_R2 0x02
-#define SD_RSP_TYPE_R3 0x05
-#define SD_RSP_TYPE_R4 0x05
-#define SD_RSP_TYPE_R5 0x01
-#define SD_RSP_TYPE_R6 0x01
-#define SD_RSP_TYPE_R7 0x01
-
-/* SD_CONFIGURE3 */
-#define SD_RSP_80CLK_TIMEOUT_EN 0x01
-
-/* Card Transfer Reset Register */
-#define SPI_STOP 0x01
-#define XD_STOP 0x02
-#define SD_STOP 0x04
-#define MS_STOP 0x08
-#define SPI_CLR_ERR 0x10
-#define XD_CLR_ERR 0x20
-#define SD_CLR_ERR 0x40
-#define MS_CLR_ERR 0x80
-
-/* Card Data Source Register */
-#define PINGPONG_BUFFER 0x01
-#define RING_BUFFER 0x00
-
-/* Card Power Control Register */
-#define PMOS_STRG_MASK 0x10
-#define PMOS_STRG_800mA 0x10
-#define PMOS_STRG_400mA 0x00
-#define SD_POWER_OFF 0x03
-#define SD_PARTIAL_POWER_ON 0x01
-#define SD_POWER_ON 0x00
-#define SD_POWER_MASK 0x03
-#define MS_POWER_OFF 0x0C
-#define MS_PARTIAL_POWER_ON 0x04
-#define MS_POWER_ON 0x00
-#define MS_POWER_MASK 0x0C
-#define BPP_POWER_OFF 0x0F
-#define BPP_POWER_5_PERCENT_ON 0x0E
-#define BPP_POWER_10_PERCENT_ON 0x0C
-#define BPP_POWER_15_PERCENT_ON 0x08
-#define BPP_POWER_ON 0x00
-#define BPP_POWER_MASK 0x0F
-#define SD_VCC_PARTIAL_POWER_ON 0x02
-#define SD_VCC_POWER_ON 0x00
-
-/* PWR_GATE_CTRL */
-#define PWR_GATE_EN 0x01
-#define LDO3318_PWR_MASK 0x06
-#define LDO_ON 0x00
-#define LDO_SUSPEND 0x04
-#define LDO_OFF 0x06
-
-/* CARD_CLK_SOURCE */
-#define CRC_FIX_CLK (0x00 << 0)
-#define CRC_VAR_CLK0 (0x01 << 0)
-#define CRC_VAR_CLK1 (0x02 << 0)
-#define SD30_FIX_CLK (0x00 << 2)
-#define SD30_VAR_CLK0 (0x01 << 2)
-#define SD30_VAR_CLK1 (0x02 << 2)
-#define SAMPLE_FIX_CLK (0x00 << 4)
-#define SAMPLE_VAR_CLK0 (0x01 << 4)
-#define SAMPLE_VAR_CLK1 (0x02 << 4)
-
-/* HOST_SLEEP_STATE */
-#define HOST_ENTER_S1 1
-#define HOST_ENTER_S3 2
+#define RTSX_PHASE_MAX 32
+#define RX_TUNING_CNT 3
#define MS_CFG 0xFD40
+#define SAMPLE_TIME_RISING 0x00
+#define SAMPLE_TIME_FALLING 0x80
+#define PUSH_TIME_DEFAULT 0x00
+#define PUSH_TIME_ODD 0x40
+#define NO_EXTEND_TOGGLE 0x00
+#define EXTEND_TOGGLE_CHK 0x20
+#define MS_BUS_WIDTH_1 0x00
+#define MS_BUS_WIDTH_4 0x10
+#define MS_BUS_WIDTH_8 0x18
+#define MS_2K_SECTOR_MODE 0x04
+#define MS_512_SECTOR_MODE 0x00
+#define MS_TOGGLE_TIMEOUT_EN 0x00
+#define MS_TOGGLE_TIMEOUT_DISEN 0x01
+#define MS_NO_CHECK_INT 0x02
#define MS_TPC 0xFD41
#define MS_TRANS_CFG 0xFD42
+#define WAIT_INT 0x80
+#define NO_WAIT_INT 0x00
+#define NO_AUTO_READ_INT_REG 0x00
+#define AUTO_READ_INT_REG 0x40
+#define MS_CRC16_ERR 0x20
+#define MS_RDY_TIMEOUT 0x10
+#define MS_INT_CMDNK 0x08
+#define MS_INT_BREQ 0x04
+#define MS_INT_ERR 0x02
+#define MS_INT_CED 0x01
#define MS_TRANSFER 0xFD43
+#define MS_TRANSFER_START 0x80
+#define MS_TRANSFER_END 0x40
+#define MS_TRANSFER_ERR 0x20
+#define MS_BS_STATE 0x10
+#define MS_TM_READ_BYTES 0x00
+#define MS_TM_NORMAL_READ 0x01
+#define MS_TM_WRITE_BYTES 0x04
+#define MS_TM_NORMAL_WRITE 0x05
+#define MS_TM_AUTO_READ 0x08
+#define MS_TM_AUTO_WRITE 0x0C
#define MS_INT_REG 0xFD44
#define MS_BYTE_CNT 0xFD45
#define MS_SECTOR_CNT_L 0xFD46
@@ -549,14 +192,90 @@
#define MS_DBUS_H 0xFD48
#define SD_CFG1 0xFDA0
+#define SD_CLK_DIVIDE_0 0x00
+#define SD_CLK_DIVIDE_256 0xC0
+#define SD_CLK_DIVIDE_128 0x80
+#define SD_BUS_WIDTH_1BIT 0x00
+#define SD_BUS_WIDTH_4BIT 0x01
+#define SD_BUS_WIDTH_8BIT 0x02
+#define SD_ASYNC_FIFO_NOT_RST 0x10
+#define SD_20_MODE 0x00
+#define SD_DDR_MODE 0x04
+#define SD_30_MODE 0x08
+#define SD_CLK_DIVIDE_MASK 0xC0
#define SD_CFG2 0xFDA1
+#define SD_CALCULATE_CRC7 0x00
+#define SD_NO_CALCULATE_CRC7 0x80
+#define SD_CHECK_CRC16 0x00
+#define SD_NO_CHECK_CRC16 0x40
+#define SD_NO_CHECK_WAIT_CRC_TO 0x20
+#define SD_WAIT_BUSY_END 0x08
+#define SD_NO_WAIT_BUSY_END 0x00
+#define SD_CHECK_CRC7 0x00
+#define SD_NO_CHECK_CRC7 0x04
+#define SD_RSP_LEN_0 0x00
+#define SD_RSP_LEN_6 0x01
+#define SD_RSP_LEN_17 0x02
+#define SD_RSP_TYPE_R0 0x04
+#define SD_RSP_TYPE_R1 0x01
+#define SD_RSP_TYPE_R1b 0x09
+#define SD_RSP_TYPE_R2 0x02
+#define SD_RSP_TYPE_R3 0x05
+#define SD_RSP_TYPE_R4 0x05
+#define SD_RSP_TYPE_R5 0x01
+#define SD_RSP_TYPE_R6 0x01
+#define SD_RSP_TYPE_R7 0x01
#define SD_CFG3 0xFDA2
+#define SD_RSP_80CLK_TIMEOUT_EN 0x01
+
#define SD_STAT1 0xFDA3
+#define SD_CRC7_ERR 0x80
+#define SD_CRC16_ERR 0x40
+#define SD_CRC_WRITE_ERR 0x20
+#define SD_CRC_WRITE_ERR_MASK 0x1C
+#define GET_CRC_TIME_OUT 0x02
+#define SD_TUNING_COMPARE_ERR 0x01
#define SD_STAT2 0xFDA4
+#define SD_RSP_80CLK_TIMEOUT 0x01
+
#define SD_BUS_STAT 0xFDA5
+#define SD_CLK_TOGGLE_EN 0x80
+#define SD_CLK_FORCE_STOP 0x40
+#define SD_DAT3_STATUS 0x10
+#define SD_DAT2_STATUS 0x08
+#define SD_DAT1_STATUS 0x04
+#define SD_DAT0_STATUS 0x02
+#define SD_CMD_STATUS 0x01
#define SD_PAD_CTL 0xFDA6
+#define SD_IO_USING_1V8 0x80
+#define SD_IO_USING_3V3 0x7F
+#define TYPE_A_DRIVING 0x00
+#define TYPE_B_DRIVING 0x01
+#define TYPE_C_DRIVING 0x02
+#define TYPE_D_DRIVING 0x03
#define SD_SAMPLE_POINT_CTL 0xFDA7
+#define DDR_FIX_RX_DAT 0x00
+#define DDR_VAR_RX_DAT 0x80
+#define DDR_FIX_RX_DAT_EDGE 0x00
+#define DDR_FIX_RX_DAT_14_DELAY 0x40
+#define DDR_FIX_RX_CMD 0x00
+#define DDR_VAR_RX_CMD 0x20
+#define DDR_FIX_RX_CMD_POS_EDGE 0x00
+#define DDR_FIX_RX_CMD_14_DELAY 0x10
+#define SD20_RX_POS_EDGE 0x00
+#define SD20_RX_14_DELAY 0x08
+#define SD20_RX_SEL_MASK 0x08
#define SD_PUSH_POINT_CTL 0xFDA8
+#define DDR_FIX_TX_CMD_DAT 0x00
+#define DDR_VAR_TX_CMD_DAT 0x80
+#define DDR_FIX_TX_DAT_14_TSU 0x00
+#define DDR_FIX_TX_DAT_12_TSU 0x40
+#define DDR_FIX_TX_CMD_NEG_EDGE 0x00
+#define DDR_FIX_TX_CMD_14_AHEAD 0x20
+#define SD20_TX_NEG_EDGE 0x00
+#define SD20_TX_14_AHEAD 0x10
+#define SD20_TX_SEL_MASK 0x10
+#define DDR_VAR_SDCLK_POL_SWAP 0x01
#define SD_CMD0 0xFDA9
#define SD_CMD_START 0x40
#define SD_CMD1 0xFDAA
@@ -569,14 +288,46 @@
#define SD_BLOCK_CNT_L 0xFDB1
#define SD_BLOCK_CNT_H 0xFDB2
#define SD_TRANSFER 0xFDB3
+#define SD_TRANSFER_START 0x80
+#define SD_TRANSFER_END 0x40
+#define SD_STAT_IDLE 0x20
+#define SD_TRANSFER_ERR 0x10
+#define SD_TM_NORMAL_WRITE 0x00
+#define SD_TM_AUTO_WRITE_3 0x01
+#define SD_TM_AUTO_WRITE_4 0x02
+#define SD_TM_AUTO_READ_3 0x05
+#define SD_TM_AUTO_READ_4 0x06
+#define SD_TM_CMD_RSP 0x08
+#define SD_TM_AUTO_WRITE_1 0x09
+#define SD_TM_AUTO_WRITE_2 0x0A
+#define SD_TM_NORMAL_READ 0x0C
+#define SD_TM_AUTO_READ_1 0x0D
+#define SD_TM_AUTO_READ_2 0x0E
+#define SD_TM_AUTO_TUNING 0x0F
#define SD_CMD_STATE 0xFDB5
+#define SD_CMD_IDLE 0x80
+
#define SD_DATA_STATE 0xFDB6
+#define SD_DATA_IDLE 0x80
#define SRCTL 0xFC13
#define DCM_DRP_CTL 0xFC23
+#define DCM_RESET 0x08
+#define DCM_LOCKED 0x04
+#define DCM_208M 0x00
+#define DCM_TX 0x01
+#define DCM_RX 0x02
#define DCM_DRP_TRIG 0xFC24
+#define DRP_START 0x80
+#define DRP_DONE 0x40
#define DCM_DRP_CFG 0xFC25
+#define DRP_WRITE 0x80
+#define DRP_READ 0x00
+#define DCM_WRITE_ADDRESS_50 0x50
+#define DCM_WRITE_ADDRESS_51 0x51
+#define DCM_READ_ADDRESS_00 0x00
+#define DCM_READ_ADDRESS_51 0x51
#define DCM_DRP_WR_DATA_L 0xFC26
#define DCM_DRP_WR_DATA_H 0xFC27
#define DCM_DRP_RD_DATA_L 0xFC28
@@ -587,42 +338,153 @@
#define SD_DCMPS1_CTL 0xFC2D
#define SD_VPTX_CTL SD_VPCLK0_CTL
#define SD_VPRX_CTL SD_VPCLK1_CTL
+#define PHASE_CHANGE 0x80
+#define PHASE_NOT_RESET 0x40
#define SD_DCMPS_TX_CTL SD_DCMPS0_CTL
#define SD_DCMPS_RX_CTL SD_DCMPS1_CTL
+#define DCMPS_CHANGE 0x80
+#define DCMPS_CHANGE_DONE 0x40
+#define DCMPS_ERROR 0x20
+#define DCMPS_CURRENT_PHASE 0x1F
#define CARD_CLK_SOURCE 0xFC2E
-
+#define CRC_FIX_CLK (0x00 << 0)
+#define CRC_VAR_CLK0 (0x01 << 0)
+#define CRC_VAR_CLK1 (0x02 << 0)
+#define SD30_FIX_CLK (0x00 << 2)
+#define SD30_VAR_CLK0 (0x01 << 2)
+#define SD30_VAR_CLK1 (0x02 << 2)
+#define SAMPLE_FIX_CLK (0x00 << 4)
+#define SAMPLE_VAR_CLK0 (0x01 << 4)
+#define SAMPLE_VAR_CLK1 (0x02 << 4)
#define CARD_PWR_CTL 0xFD50
+#define PMOS_STRG_MASK 0x10
+#define PMOS_STRG_800mA 0x10
+#define PMOS_STRG_400mA 0x00
+#define SD_POWER_OFF 0x03
+#define SD_PARTIAL_POWER_ON 0x01
+#define SD_POWER_ON 0x00
+#define SD_POWER_MASK 0x03
+#define MS_POWER_OFF 0x0C
+#define MS_PARTIAL_POWER_ON 0x04
+#define MS_POWER_ON 0x00
+#define MS_POWER_MASK 0x0C
+#define BPP_POWER_OFF 0x0F
+#define BPP_POWER_5_PERCENT_ON 0x0E
+#define BPP_POWER_10_PERCENT_ON 0x0C
+#define BPP_POWER_15_PERCENT_ON 0x08
+#define BPP_POWER_ON 0x00
+#define BPP_POWER_MASK 0x0F
+#define SD_VCC_PARTIAL_POWER_ON 0x02
+#define SD_VCC_POWER_ON 0x00
#define CARD_CLK_SWITCH 0xFD51
#define RTL8411B_PACKAGE_MODE 0xFD51
#define CARD_SHARE_MODE 0xFD52
+#define CARD_SHARE_MASK 0x0F
+#define CARD_SHARE_MULTI_LUN 0x00
+#define CARD_SHARE_NORMAL 0x00
+#define CARD_SHARE_48_SD 0x04
+#define CARD_SHARE_48_MS 0x08
+#define CARD_SHARE_BAROSSA_SD 0x01
+#define CARD_SHARE_BAROSSA_MS 0x02
#define CARD_DRIVE_SEL 0xFD53
+#define MS_DRIVE_8mA (0x01 << 6)
+#define MMC_DRIVE_8mA (0x01 << 4)
+#define XD_DRIVE_8mA (0x01 << 2)
+#define GPIO_DRIVE_8mA 0x01
+#define RTS5209_CARD_DRIVE_DEFAULT (MS_DRIVE_8mA | MMC_DRIVE_8mA |\
+ XD_DRIVE_8mA | GPIO_DRIVE_8mA)
+#define RTL8411_CARD_DRIVE_DEFAULT (MS_DRIVE_8mA | MMC_DRIVE_8mA |\
+ XD_DRIVE_8mA)
+#define RTSX_CARD_DRIVE_DEFAULT (MS_DRIVE_8mA | GPIO_DRIVE_8mA)
+
#define CARD_STOP 0xFD54
+#define SPI_STOP 0x01
+#define XD_STOP 0x02
+#define SD_STOP 0x04
+#define MS_STOP 0x08
+#define SPI_CLR_ERR 0x10
+#define XD_CLR_ERR 0x20
+#define SD_CLR_ERR 0x40
+#define MS_CLR_ERR 0x80
#define CARD_OE 0xFD55
+#define SD_OUTPUT_EN 0x04
+#define MS_OUTPUT_EN 0x08
#define CARD_AUTO_BLINK 0xFD56
#define CARD_GPIO_DIR 0xFD57
#define CARD_GPIO 0xFD58
#define CARD_DATA_SOURCE 0xFD5B
+#define PINGPONG_BUFFER 0x01
+#define RING_BUFFER 0x00
#define SD30_CLK_DRIVE_SEL 0xFD5A
+#define DRIVER_TYPE_A 0x05
+#define DRIVER_TYPE_B 0x03
+#define DRIVER_TYPE_C 0x02
+#define DRIVER_TYPE_D 0x01
#define CARD_SELECT 0xFD5C
+#define SD_MOD_SEL 2
+#define MS_MOD_SEL 3
#define SD30_DRIVE_SEL 0xFD5E
+#define CFG_DRIVER_TYPE_A 0x02
+#define CFG_DRIVER_TYPE_B 0x03
+#define CFG_DRIVER_TYPE_C 0x01
+#define CFG_DRIVER_TYPE_D 0x00
#define SD30_CMD_DRIVE_SEL 0xFD5E
#define SD30_DAT_DRIVE_SEL 0xFD5F
#define CARD_CLK_EN 0xFD69
+#define SD_CLK_EN 0x04
+#define MS_CLK_EN 0x08
#define SDIO_CTRL 0xFD6B
#define CD_PAD_CTL 0xFD73
-
+#define CD_DISABLE_MASK 0x07
+#define MS_CD_DISABLE 0x04
+#define SD_CD_DISABLE 0x02
+#define XD_CD_DISABLE 0x01
+#define CD_DISABLE 0x07
+#define CD_ENABLE 0x00
+#define MS_CD_EN_ONLY 0x03
+#define SD_CD_EN_ONLY 0x05
+#define XD_CD_EN_ONLY 0x06
+#define FORCE_CD_LOW_MASK 0x38
+#define FORCE_CD_XD_LOW 0x08
+#define FORCE_CD_SD_LOW 0x10
+#define FORCE_CD_MS_LOW 0x20
+#define CD_AUTO_DISABLE 0x40
#define FPDCTL 0xFC00
+#define SSC_POWER_DOWN 0x01
+#define SD_OC_POWER_DOWN 0x02
+#define ALL_POWER_DOWN 0x07
+#define OC_POWER_DOWN 0x06
#define PDINFO 0xFC01
#define CLK_CTL 0xFC02
+#define CHANGE_CLK 0x01
+#define CLK_LOW_FREQ 0x01
+
#define CLK_DIV 0xFC03
+#define CLK_DIV_1 0x01
+#define CLK_DIV_2 0x02
+#define CLK_DIV_4 0x03
+#define CLK_DIV_8 0x04
#define CLK_SEL 0xFC04
#define SSC_DIV_N_0 0xFC0F
#define SSC_DIV_N_1 0xFC10
#define SSC_CTL1 0xFC11
+#define SSC_RSTB 0x80
+#define SSC_8X_EN 0x40
+#define SSC_FIX_FRAC 0x20
+#define SSC_SEL_1M 0x00
+#define SSC_SEL_2M 0x08
+#define SSC_SEL_4M 0x10
+#define SSC_SEL_8M 0x18
#define SSC_CTL2 0xFC12
-
+#define SSC_DEPTH_MASK 0x07
+#define SSC_DEPTH_DISALBE 0x00
+#define SSC_DEPTH_4M 0x01
+#define SSC_DEPTH_2M 0x02
+#define SSC_DEPTH_1M 0x03
+#define SSC_DEPTH_500K 0x04
+#define SSC_DEPTH_250K 0x05
#define RCCTL 0xFC14
#define FPGA_PULL_CTL 0xFC1D
@@ -630,6 +492,24 @@
#define GPIO_CTL 0xFC1F
#define LDO_CTL 0xFC1E
+#define BPP_ASIC_1V7 0x00
+#define BPP_ASIC_1V8 0x01
+#define BPP_ASIC_1V9 0x02
+#define BPP_ASIC_2V0 0x03
+#define BPP_ASIC_2V7 0x04
+#define BPP_ASIC_2V8 0x05
+#define BPP_ASIC_3V2 0x06
+#define BPP_ASIC_3V3 0x07
+#define BPP_REG_TUNED18 0x07
+#define BPP_TUNED18_SHIFT_8402 5
+#define BPP_TUNED18_SHIFT_8411 4
+#define BPP_PAD_MASK 0x04
+#define BPP_PAD_3V3 0x04
+#define BPP_PAD_1V8 0x00
+#define BPP_LDO_POWB 0x03
+#define BPP_LDO_ON 0x00
+#define BPP_LDO_SUSPEND 0x02
+#define BPP_LDO_OFF 0x03
#define SYS_VER 0xFC32
#define CARD_PULL_CTL1 0xFD60
@@ -642,6 +522,10 @@
/* PCI Express Related Registers */
#define IRQEN0 0xFE20
#define IRQSTAT0 0xFE21
+#define DMA_DONE_INT 0x80
+#define SUSPEND_INT 0x40
+#define LINK_RDY_INT 0x20
+#define LINK_DOWN_INT 0x10
#define IRQEN1 0xFE22
#define IRQSTAT1 0xFE23
#define TLPRIEN 0xFE24
@@ -653,6 +537,16 @@
#define DMATC2 0xFE2A
#define DMATC3 0xFE2B
#define DMACTL 0xFE2C
+#define DMA_RST 0x80
+#define DMA_BUSY 0x04
+#define DMA_DIR_TO_CARD 0x00
+#define DMA_DIR_FROM_CARD 0x02
+#define DMA_EN 0x01
+#define DMA_128 (0 << 4)
+#define DMA_256 (1 << 4)
+#define DMA_512 (2 << 4)
+#define DMA_1024 (3 << 4)
+#define DMA_PACK_SIZE_MASK 0x30
#define BCTL 0xFE2D
#define RBBC0 0xFE2E
#define RBBC1 0xFE2F
@@ -693,11 +587,19 @@
#define RESET_LOAD_REG 0xFE5E
#define EFUSE_CONTENT 0xFE5F
#define HOST_SLEEP_STATE 0xFE60
+#define HOST_ENTER_S1 1
+#define HOST_ENTER_S3 2
+
#define SDIO_CFG 0xFE70
#define NFTS_TX_CTRL 0xFE72
#define PWR_GATE_CTRL 0xFE75
+#define PWR_GATE_EN 0x01
+#define LDO3318_PWR_MASK 0x06
+#define LDO_ON 0x00
+#define LDO_SUSPEND 0x04
+#define LDO_OFF 0x06
#define PWD_SUSPEND_EN 0xFE76
#define LDO_PWR_SEL 0xFE78
--
1.9.1
More information about the devel
mailing list