[PATCH 1/8] staging: dgap: Fix trailing whitespace in digi.h
Lidza Louina
lidza.louina at gmail.com
Fri Jan 17 16:45:40 UTC 2014
Acked-by: Lidza Louina <Lidza.Louina at gmail.com>
On Tue, Jan 14, 2014 at 10:40 AM, Masanari Iida <standby24x7 at gmail.com> wrote:
> This patch fixed trailing whitespace error found by
> checkpatch.pl in dgap/digi.h
>
> Signed-off-by: Masanari Iida <standby24x7 at gmail.com>
> ---
> drivers/staging/dgap/digi.h | 24 ++++++++++++------------
> 1 file changed, 12 insertions(+), 12 deletions(-)
>
> diff --git a/drivers/staging/dgap/digi.h b/drivers/staging/dgap/digi.h
> index bcea4f7..fe87903 100644
> --- a/drivers/staging/dgap/digi.h
> +++ b/drivers/staging/dgap/digi.h
> @@ -43,7 +43,7 @@
> #define TIOCMODG ('d'<<8) | 250 /* get modem ctrl state */
> #define TIOCMODS ('d'<<8) | 251 /* set modem ctrl state */
>
> -#ifndef TIOCM_LE
> +#ifndef TIOCM_LE
> #define TIOCM_LE 0x01 /* line enable */
> #define TIOCM_DTR 0x02 /* data terminal ready */
> #define TIOCM_RTS 0x04 /* request to send */
> @@ -122,7 +122,7 @@ struct digiflow_t {
> #endif
>
> /************************************************************************
> - * Values for digi_flags
> + * Values for digi_flags
> ************************************************************************/
> #define DIGI_IXON 0x0001 /* Handle IXON in the FEP */
> #define DIGI_FAST 0x0002 /* Fast baud rates */
> @@ -193,8 +193,8 @@ struct rw_t {
> #define COMXI_TYPE 5 /* Board type at the designated port is a COM/Xi */
>
> /* Non-Zero Result codes. */
> -#define RESULT_NOBDFND 1 /* A Digi product at that port is not config installed */
> -#define RESULT_NODESCT 2 /* A memory descriptor was not obtainable */
> +#define RESULT_NOBDFND 1 /* A Digi product at that port is not config installed */
> +#define RESULT_NODESCT 2 /* A memory descriptor was not obtainable */
> #define RESULT_NOOSSIG 3 /* FEP/OS signature was not detected on the board */
> #define RESULT_TOOSML 4 /* Too small an area to shrink. */
> #define RESULT_NOCHAN 5 /* Channel structure for the board was not found */
> @@ -205,7 +205,7 @@ struct shrink_buf_struct {
> unsigned long shrink_buf_bseg; /* Amount of board memory */
> unsigned long shrink_buf_hseg; /* '186 Beginning of Dual-Port */
>
> - unsigned long shrink_buf_lseg; /* '186 Beginning of freed memory */
> + unsigned long shrink_buf_lseg; /* '186 Beginning of freed memory */
> unsigned long shrink_buf_mseg; /* Linear address from start of
> dual-port were freed memory
> begins, host viewpoint. */
> @@ -220,18 +220,18 @@ struct shrink_buf_struct {
>
> unsigned char shrink_buf_result; /* Reason for call failing
> Zero is Good return */
> - unsigned char shrink_buf_init; /* Non-Zero if it caused an
> + unsigned char shrink_buf_init; /* Non-Zero if it caused an
> xxinit call. */
>
> unsigned char shrink_buf_anports; /* Number of async ports */
> unsigned char shrink_buf_snports; /* Number of sync ports */
> unsigned char shrink_buf_type; /* Board type 1 = PC/Xi,
> 2 = PC/Xm,
> - 3 = PC/Xe
> - 4 = MC/Xi
> + 3 = PC/Xe
> + 4 = MC/Xi
> 5 = COMX/i */
> unsigned char shrink_buf_card; /* Card number */
> -
> +
> };
>
> /************************************************************************
> @@ -244,7 +244,7 @@ struct digi_dinfo {
> };
>
> #define DIGI_GETDD ('d'<<8) | 248 /* get driver info */
> -
> +
> /************************************************************************
> * Structure used with ioctl commands for per-board information
> *
> @@ -264,7 +264,7 @@ struct digi_info {
> };
>
> #define DIGI_GETBD ('d'<<8) | 249 /* get board info */
> -
> +
> struct digi_stat {
> unsigned int info_chan; /* Channel number (0 based) */
> unsigned int info_brd; /* Board number (0 based) */
> @@ -299,7 +299,7 @@ struct digi_ch {
> };
>
> /*
> -* This structure is used with the DIGI_FEPCMD ioctl to
> +* This structure is used with the DIGI_FEPCMD ioctl to
> * tell the driver which port to send the command for.
> */
> struct digi_cmd {
> --
> 1.8.5.2.309.ga25014b
>
More information about the devel
mailing list