[PATCH 06/22] staging: comedi: rtd520: remove the unused #define's in the header
H Hartley Sweeten
hsweeten at visionengravers.com
Tue Mar 26 22:00:02 UTC 2013
Remove all the unused defines in the private header.
Signed-off-by: H Hartley Sweeten <hsweeten at visionengravers.com>
Cc: Ian Abbott <abbotti at mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh at linuxfoundation.org>
---
drivers/staging/comedi/drivers/rtd520.h | 217 --------------------------------
1 file changed, 217 deletions(-)
diff --git a/drivers/staging/comedi/drivers/rtd520.h b/drivers/staging/comedi/drivers/rtd520.h
index bfb3437..52fb8e2 100644
--- a/drivers/staging/comedi/drivers/rtd520.h
+++ b/drivers/staging/comedi/drivers/rtd520.h
@@ -127,152 +127,6 @@
#define FS_DIN_HEMPTY (1 << 13) /* DIN FIFO half empty */
#define FS_DIN_NOT_FULL (1 << 14) /* DIN FIFO not full */
-/* Timer Status Word Bits (GetTimerStatus) */
-#define TS_PCLK_GATE (1 << 0) /* Pacer Clock Gate enabled */
-#define TS_BCLK_GATE (1 << 1) /* Burst Clock Gate running */
-#define TS_DCNT_GATE (1 << 2) /* Pacer Clock Delayed Start Trig. */
-#define TS_ACNT_GATE (1 << 3) /* Pacer Clock About Trig. */
-#define TS_PCLK_RUN (1 << 4) /* Pacer Clock Shutdown Flag */
-
-/* External Trigger polarity select */
-/* External Interrupt polarity select */
-#define POL_POSITIVE 0x0 /* positive edge */
-#define POL_NEGATIVE 0x1 /* negative edge */
-
-/* User Output Signal select (SetUout0Source, SetUout1Source) */
-#define UOUT_ADC 0x0 /* A/D Conversion Signal */
-#define UOUT_DAC1 0x1 /* D/A1 Update */
-#define UOUT_DAC2 0x2 /* D/A2 Update */
-#define UOUT_SOFTWARE 0x3 /* Software Programmable */
-
-/* Pacer clock select (SetPacerSource) */
-#define PCLK_INTERNAL 1 /* Internal Pacer Clock */
-#define PCLK_EXTERNAL 0 /* External Pacer Clock */
-
-/* A/D Sample Counter Sources (SetAdcntSource, SetupSampleCounter) */
-#define ADC_SCNT_CGT_RESET 0x0 /* needs restart with StartPacer */
-#define ADC_SCNT_FIFO_WRITE 0x1
-
-/* A/D Conversion Signal Select (for SetConversionSelect) */
-#define ADC_START_SOFTWARE 0x0 /* Software A/D Start */
-#define ADC_START_PCLK 0x1 /* Pacer Clock (Ext. Int. see Func.509) */
-#define ADC_START_BCLK 0x2 /* Burst Clock */
-#define ADC_START_DIGITAL_IT 0x3 /* Digital Interrupt */
-#define ADC_START_DAC1_MARKER1 0x4 /* D/A 1 Data Marker 1 */
-#define ADC_START_DAC2_MARKER1 0x5 /* D/A 2 Data Marker 1 */
-#define ADC_START_SBUS0 0x6 /* SyncBus 0 */
-#define ADC_START_SBUS1 0x7 /* SyncBus 1 */
-#define ADC_START_SBUS2 0x8 /* SyncBus 2 */
-
-/* Burst Clock start trigger select (SetBurstStart) */
-#define BCLK_START_SOFTWARE 0x0 /* Software A/D Start (StartBurst) */
-#define BCLK_START_PCLK 0x1 /* Pacer Clock */
-#define BCLK_START_ETRIG 0x2 /* External Trigger */
-#define BCLK_START_DIGITAL_IT 0x3 /* Digital Interrupt */
-#define BCLK_START_SBUS0 0x4 /* SyncBus 0 */
-#define BCLK_START_SBUS1 0x5 /* SyncBus 1 */
-#define BCLK_START_SBUS2 0x6 /* SyncBus 2 */
-
-/* Pacer Clock start trigger select (SetPacerStart) */
-#define PCLK_START_SOFTWARE 0x0 /* Software Pacer Start (StartPacer) */
-#define PCLK_START_ETRIG 0x1 /* External trigger */
-#define PCLK_START_DIGITAL_IT 0x2 /* Digital interrupt */
-#define PCLK_START_UTC2 0x3 /* User TC 2 out */
-#define PCLK_START_SBUS0 0x4 /* SyncBus 0 */
-#define PCLK_START_SBUS1 0x5 /* SyncBus 1 */
-#define PCLK_START_SBUS2 0x6 /* SyncBus 2 */
-#define PCLK_START_D_SOFTWARE 0x8 /* Delayed Software Pacer Start */
-#define PCLK_START_D_ETRIG 0x9 /* Delayed external trigger */
-#define PCLK_START_D_DIGITAL_IT 0xA /* Delayed digital interrupt */
-#define PCLK_START_D_UTC2 0xB /* Delayed User TC 2 out */
-#define PCLK_START_D_SBUS0 0xC /* Delayed SyncBus 0 */
-#define PCLK_START_D_SBUS1 0xD /* Delayed SyncBus 1 */
-#define PCLK_START_D_SBUS2 0xE /* Delayed SyncBus 2 */
-#define PCLK_START_ETRIG_GATED 0xF /* External Trigger Gated controlled mode */
-
-/* Pacer Clock Stop Trigger select (SetPacerStop) */
-#define PCLK_STOP_SOFTWARE 0x0 /* Software Pacer Stop (StopPacer) */
-#define PCLK_STOP_ETRIG 0x1 /* External Trigger */
-#define PCLK_STOP_DIGITAL_IT 0x2 /* Digital Interrupt */
-#define PCLK_STOP_ACNT 0x3 /* About Counter */
-#define PCLK_STOP_UTC2 0x4 /* User TC2 out */
-#define PCLK_STOP_SBUS0 0x5 /* SyncBus 0 */
-#define PCLK_STOP_SBUS1 0x6 /* SyncBus 1 */
-#define PCLK_STOP_SBUS2 0x7 /* SyncBus 2 */
-#define PCLK_STOP_A_SOFTWARE 0x8 /* About Software Pacer Stop */
-#define PCLK_STOP_A_ETRIG 0x9 /* About External Trigger */
-#define PCLK_STOP_A_DIGITAL_IT 0xA /* About Digital Interrupt */
-#define PCLK_STOP_A_UTC2 0xC /* About User TC2 out */
-#define PCLK_STOP_A_SBUS0 0xD /* About SyncBus 0 */
-#define PCLK_STOP_A_SBUS1 0xE /* About SyncBus 1 */
-#define PCLK_STOP_A_SBUS2 0xF /* About SyncBus 2 */
-
-/* About Counter Stop Enable */
-#define ACNT_STOP 0x0 /* stop enable */
-#define ACNT_NO_STOP 0x1 /* stop disabled */
-
-/* DAC update source (SetDAC1Start & SetDAC2Start) */
-#define DAC_START_SOFTWARE 0x0 /* Software Update */
-#define DAC_START_CGT 0x1 /* CGT controlled Update */
-#define DAC_START_DAC_CLK 0x2 /* D/A Clock */
-#define DAC_START_EPCLK 0x3 /* External Pacer Clock */
-#define DAC_START_SBUS0 0x4 /* SyncBus 0 */
-#define DAC_START_SBUS1 0x5 /* SyncBus 1 */
-#define DAC_START_SBUS2 0x6 /* SyncBus 2 */
-
-/* DAC Cycle Mode (SetDAC1Cycle, SetDAC2Cycle, SetupDAC) */
-#define DAC_CYCLE_SINGLE 0x0 /* not cycle */
-#define DAC_CYCLE_MULTI 0x1 /* cycle */
-
-/* 8254 Operation Modes (Set8254Mode, SetupTimerCounter) */
-#define M8254_EVENT_COUNTER 0 /* Event Counter */
-#define M8254_HW_ONE_SHOT 1 /* Hardware-Retriggerable One-Shot */
-#define M8254_RATE_GENERATOR 2 /* Rate Generator */
-#define M8254_SQUARE_WAVE 3 /* Square Wave Mode */
-#define M8254_SW_STROBE 4 /* Software Triggered Strobe */
-#define M8254_HW_STROBE 5 /* Hardware Triggered Strobe (Retriggerable) */
-
-/* User Timer/Counter 0 Clock Select (SetUtc0Clock) */
-#define CUTC0_8MHZ 0x0 /* 8MHz */
-#define CUTC0_EXT_TC_CLOCK1 0x1 /* Ext. TC Clock 1 */
-#define CUTC0_EXT_TC_CLOCK2 0x2 /* Ext. TC Clock 2 */
-#define CUTC0_EXT_PCLK 0x3 /* Ext. Pacer Clock */
-
-/* User Timer/Counter 1 Clock Select (SetUtc1Clock) */
-#define CUTC1_8MHZ 0x0 /* 8MHz */
-#define CUTC1_EXT_TC_CLOCK1 0x1 /* Ext. TC Clock 1 */
-#define CUTC1_EXT_TC_CLOCK2 0x2 /* Ext. TC Clock 2 */
-#define CUTC1_EXT_PCLK 0x3 /* Ext. Pacer Clock */
-#define CUTC1_UTC0_OUT 0x4 /* User Timer/Counter 0 out */
-#define CUTC1_DIN_SIGNAL 0x5 /* High-Speed Digital Input Sampling signal */
-
-/* User Timer/Counter 2 Clock Select (SetUtc2Clock) */
-#define CUTC2_8MHZ 0x0 /* 8MHz */
-#define CUTC2_EXT_TC_CLOCK1 0x1 /* Ext. TC Clock 1 */
-#define CUTC2_EXT_TC_CLOCK2 0x2 /* Ext. TC Clock 2 */
-#define CUTC2_EXT_PCLK 0x3 /* Ext. Pacer Clock */
-#define CUTC2_UTC1_OUT 0x4 /* User Timer/Counter 1 out */
-
-/* User Timer/Counter 0 Gate Select (SetUtc0Gate) */
-#define GUTC0_NOT_GATED 0x0 /* Not gated */
-#define GUTC0_GATED 0x1 /* Gated */
-#define GUTC0_EXT_TC_GATE1 0x2 /* Ext. TC Gate 1 */
-#define GUTC0_EXT_TC_GATE2 0x3 /* Ext. TC Gate 2 */
-
-/* User Timer/Counter 1 Gate Select (SetUtc1Gate) */
-#define GUTC1_NOT_GATED 0x0 /* Not gated */
-#define GUTC1_GATED 0x1 /* Gated */
-#define GUTC1_EXT_TC_GATE1 0x2 /* Ext. TC Gate 1 */
-#define GUTC1_EXT_TC_GATE2 0x3 /* Ext. TC Gate 2 */
-#define GUTC1_UTC0_OUT 0x4 /* User Timer/Counter 0 out */
-
-/* User Timer/Counter 2 Gate Select (SetUtc2Gate) */
-#define GUTC2_NOT_GATED 0x0 /* Not gated */
-#define GUTC2_GATED 0x1 /* Gated */
-#define GUTC2_EXT_TC_GATE1 0x2 /* Ext. TC Gate 1 */
-#define GUTC2_EXT_TC_GATE2 0x3 /* Ext. TC Gate 2 */
-#define GUTC2_UTC1_OUT 0x4 /* User Timer/Counter 1 out */
-
/* Interrupt Source Masks (SetITMask, ClearITMask, GetITStatus) */
#define IRQM_ADC_FIFO_WRITE 0x0001 /* ADC FIFO Write */
#define IRQM_CGT_RESET 0x0002 /* Reset CGT */
@@ -289,74 +143,3 @@
#define IRQM_EXTERNAL_IT 0x2000 /* External Interrupt */
#define IRQM_ETRIG_RISING 0x4000 /* External Trigger rising-edge */
#define IRQM_ETRIG_FALLING 0x8000 /* External Trigger falling-edge */
-
-/* DMA Request Sources (LAS0) */
-#define DMAS_DISABLED 0x0 /* DMA Disabled */
-#define DMAS_ADC_SCNT 0x1 /* ADC Sample Counter */
-#define DMAS_DAC1_UCNT 0x2 /* D/A1 Update Counter */
-#define DMAS_DAC2_UCNT 0x3 /* D/A2 Update Counter */
-#define DMAS_UTC1 0x4 /* User TC1 out */
-#define DMAS_ADFIFO_HALF_FULL 0x8 /* A/D FIFO half full */
-#define DMAS_DAC1_FIFO_HALF_EMPTY 0x9 /* D/A1 FIFO half empty */
-#define DMAS_DAC2_FIFO_HALF_EMPTY 0xA /* D/A2 FIFO half empty */
-
-/* DMA Local Addresses (0x40000000+LAS1 offset) */
-#define DMALADDR_ADC 0x40000000 /* A/D FIFO */
-#define DMALADDR_HDIN 0x40000004 /* High Speed Digital Input FIFO */
-#define DMALADDR_DAC1 0x40000008 /* D/A1 FIFO */
-#define DMALADDR_DAC2 0x4000000C /* D/A2 FIFO */
-
-/* Port 0 compare modes (SetDIO0CompareMode) */
-#define DIO_MODE_EVENT 0 /* Event Mode */
-#define DIO_MODE_MATCH 1 /* Match Mode */
-
-/* Digital Table Enable (Port 1 disable) */
-#define DTBL_DISABLE 0 /* Enable Digital Table */
-#define DTBL_ENABLE 1 /* Disable Digital Table */
-
-/* Sampling Signal for High Speed Digital Input (SetHdinStart) */
-#define HDIN_SOFTWARE 0x0 /* Software Trigger */
-#define HDIN_ADC 0x1 /* A/D Conversion Signal */
-#define HDIN_UTC0 0x2 /* User TC out 0 */
-#define HDIN_UTC1 0x3 /* User TC out 1 */
-#define HDIN_UTC2 0x4 /* User TC out 2 */
-#define HDIN_EPCLK 0x5 /* External Pacer Clock */
-#define HDIN_ETRG 0x6 /* External Trigger */
-
-/* Channel Gain Table / Channel Gain Latch */
-#define CSC_LATCH 0 /* Channel Gain Latch mode */
-#define CSC_CGT 1 /* Channel Gain Table mode */
-
-/* Channel Gain Table Pause Enable */
-#define CGT_PAUSE_DISABLE 0 /* Channel Gain Table Pause Disable */
-#define CGT_PAUSE_ENABLE 1 /* Channel Gain Table Pause Enable */
-
-/* DAC output type/range (p63) */
-#define AOUT_UNIP5 0 /* 0..+5 Volt */
-#define AOUT_UNIP10 1 /* 0..+10 Volt */
-#define AOUT_BIP5 2 /* -5..+5 Volt */
-#define AOUT_BIP10 3 /* -10..+10 Volt */
-
-/* Ghannel Gain Table field definitions (p61) */
-/* Gain */
-#define GAIN1 0
-#define GAIN2 1
-#define GAIN4 2
-#define GAIN8 3
-#define GAIN16 4
-#define GAIN32 5
-#define GAIN64 6
-#define GAIN128 7
-
-/* Input range/polarity */
-#define AIN_BIP5 0 /* -5..+5 Volt */
-#define AIN_BIP10 1 /* -10..+10 Volt */
-#define AIN_UNIP10 2 /* 0..+10 Volt */
-
-/* non referenced single ended select bit */
-#define NRSE_AGND 0 /* AGND referenced SE input */
-#define NRSE_AINS 1 /* AIN SENSE referenced SE input */
-
-/* single ended vs differential */
-#define GND_SE 0 /* Single-Ended */
-#define GND_DIFF 1 /* Differential */
--
1.8.1.4
More information about the devel
mailing list