[PATCH 27/51 v2] staging: comedi: ni_labpc: cleanup local var declarations in labpc_ai_cmd()
H Hartley Sweeten
hsweeten at visionengravers.com
Fri Mar 22 16:47:51 UTC 2013
Determine the scan_mode early and get the proper chanspec so that
the chan, range, and aref can be determined when the variables are
declared.
labpc_ai_chanlist_invalid() checks that all the range and aref values
in the chanlist are the same so, for consistency, use the same chanspec
used to get the chan.
Signed-off-by: H Hartley Sweeten <hsweeten at visionengravers.com>
Cc: Ian Abbott <abbotti at mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh at linuxfoundation.org>
---
drivers/staging/comedi/drivers/ni_labpc.c | 23 ++++++++++-------------
1 file changed, 10 insertions(+), 13 deletions(-)
diff --git a/drivers/staging/comedi/drivers/ni_labpc.c b/drivers/staging/comedi/drivers/ni_labpc.c
index 56d6084..3672ba8 100644
--- a/drivers/staging/comedi/drivers/ni_labpc.c
+++ b/drivers/staging/comedi/drivers/ni_labpc.c
@@ -850,16 +850,18 @@ static int labpc_ai_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
{
const struct labpc_boardinfo *board = comedi_board(dev);
struct labpc_private *devpriv = dev->private;
- int channel, range, aref;
- int ret;
struct comedi_async *async = s->async;
struct comedi_cmd *cmd = &async->cmd;
+ enum scan_mode mode = labpc_ai_scan_mode(cmd);
+ unsigned int chanspec = (mode == MODE_MULT_CHAN_UP)
+ ? cmd->chanlist[cmd->chanlist_len - 1]
+ : cmd->chanlist[0];
+ unsigned int chan = CR_CHAN(chanspec);
+ unsigned int range = CR_RANGE(chanspec);
+ unsigned int aref = CR_AREF(chanspec);
enum transfer_type xfer;
- enum scan_mode mode;
unsigned long flags;
-
- range = CR_RANGE(cmd->chanlist[0]);
- aref = CR_AREF(cmd->chanlist[0]);
+ int ret;
/* make sure board is disabled before setting up acquisition */
spin_lock_irqsave(&dev->spinlock, flags);
@@ -916,7 +918,6 @@ static int labpc_ai_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
} else
xfer = fifo_not_empty_transfer;
devpriv->current_transfer = xfer;
- mode = labpc_ai_scan_mode(cmd);
/* setup cmd6 register for 1200 boards */
if (board->register_layout == labpc_1200_layout) {
@@ -951,15 +952,11 @@ static int labpc_ai_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
/* setup channel list, etc (cmd1 register) */
devpriv->cmd1 = 0;
- if (mode == MODE_MULT_CHAN_UP)
- channel = CR_CHAN(cmd->chanlist[cmd->chanlist_len - 1]);
- else
- channel = CR_CHAN(cmd->chanlist[0]);
/* munge channel bits for differential / scan disabled mode */
if ((mode == MODE_SINGLE_CHAN || mode == MODE_SINGLE_CHAN_INTERVAL) &&
aref == AREF_DIFF)
- channel *= 2;
- devpriv->cmd1 |= ADC_CHAN_BITS(channel);
+ chan *= 2;
+ devpriv->cmd1 |= ADC_CHAN_BITS(chan);
devpriv->cmd1 |= board->ai_range_code[range];
devpriv->write_byte(devpriv->cmd1, dev->iobase + COMMAND1_REG);
/* manual says to set scan enable bit on second pass */
--
1.8.1.4
More information about the devel
mailing list