[PATCH 6/6] staging: dwc2: remove use of bus_to_virt()

[Paul Zimmerman]

Remove the use of bus_to_virt() and just fail the transfer if an
unaligned buffer with no virtual address is found. AFAIK that
can't happen anyway.

Also change setting of coherent DMA mask to the normal 32 bits.
31 bits was only needed when calling bus_to_virt() AFAICR.

Signed-off-by: Paul Zimmerman <paulz at synopsys.com>
---
 drivers/staging/dwc2/Kconfig |  1 -
 drivers/staging/dwc2/hcd.c   | 20 ++++++++++----------
 2 files changed, 10 insertions(+), 11 deletions(-)

diff --git a/drivers/staging/dwc2/Kconfig b/drivers/staging/dwc2/Kconfig
index d15d9d5..be947d6 100644
--- a/drivers/staging/dwc2/Kconfig
+++ b/drivers/staging/dwc2/Kconfig
@@ -1,7 +1,6 @@
 config USB_DWC2
 	tristate "DesignWare USB2 DRD Core Support"
 	depends on USB
-	depends on VIRT_TO_BUS
 	help
 	  Say Y or M here if your system has a Dual Role HighSpeed
 	  USB controller based on the DesignWare HSOTG IP Core.
diff --git a/drivers/staging/dwc2/hcd.c b/drivers/staging/dwc2/hcd.c
index 2639209..962468f 100644
--- a/drivers/staging/dwc2/hcd.c
+++ b/drivers/staging/dwc2/hcd.c
@@ -2396,14 +2396,15 @@ static int _dwc2_hcd_urb_enqueue(struct usb_hcd *hcd, struct urb *urb,
 						!(usb_pipein(urb->pipe))));
 
 	buf = urb->transfer_buffer;
+
 	if (hcd->self.uses_dma) {
-		/*
-		 * Calculate virtual address from physical address, because
-		 * some class driver may not fill transfer_buffer.
-		 * In Buffer DMA mode virtual address is used, when handling
-		 * non-DWORD aligned buffers.
-		 */
-		buf = bus_to_virt(urb->transfer_dma);
+		if (!buf && (urb->transfer_dma & 3)) {
+			dev_err(hsotg->dev,
+				"%s: unaligned transfer with no transfer_buffer",
+				__func__);
+			retval = -EINVAL;
+			goto fail1;
+		}
 	}
 
 	if (!(urb->transfer_flags & URB_NO_INTERRUPT))
@@ -2833,9 +2834,8 @@ int dwc2_hcd_init(struct dwc2_hsotg *hsotg, int irq,
 	if (hsotg->core_params->dma_enable > 0) {
 		if (dma_set_mask(hsotg->dev, DMA_BIT_MASK(32)) < 0)
 			dev_warn(hsotg->dev, "can't set DMA mask\n");
-		if (dma_set_coherent_mask(hsotg->dev, DMA_BIT_MASK(31)) < 0)
-			dev_warn(hsotg->dev,
-				 "can't enable workaround for >2GB RAM\n");
+		if (dma_set_coherent_mask(hsotg->dev, DMA_BIT_MASK(32)) < 0)
+			dev_warn(hsotg->dev, "can't set coherent DMA mask\n");
 	} else {
 		dma_set_mask(hsotg->dev, 0);
 		dma_set_coherent_mask(hsotg->dev, 0);
-- 
1.8.2.rc0.16.g20a599e