[PATCH 06/51] staging: comedi: pcl818: remove 'irq_free' from private data

[H Hartley Sweeten]

This member of the private data is not needed. We can check if
dev->irq is none zero instead. Remove it.

Signed-off-by: H Hartley Sweeten <hsweeten at visionengravers.com>
Cc: Ian Abbott <abbotti at mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh at linuxfoundation.org>
---
 drivers/staging/comedi/drivers/pcl818.c | 10 +++-------
 1 file changed, 3 insertions(+), 7 deletions(-)

diff --git a/drivers/staging/comedi/drivers/pcl818.c b/drivers/staging/comedi/drivers/pcl818.c
index cacdca0..3dac1dd 100644
--- a/drivers/staging/comedi/drivers/pcl818.c
+++ b/drivers/staging/comedi/drivers/pcl818.c
@@ -274,7 +274,6 @@ struct pcl818_private {
 	unsigned char neverending_ai;	/*  if=1, then we do neverending record (you must use cancel()) */
 	unsigned int ns_min;	/*  manimal allowed delay between samples (in us) for actual card */
 	int i8253_osc_base;	/*  1/frequency of on board oscilator in ns */
-	int irq_free;		/*  1=have allocated IRQ */
 	int irq_blocked;	/*  1=IRQ now uses any subdev */
 	int irq_was_now_closed;	/*  when IRQ finish, there's stored int818_mode for last interrupt */
 	int ai_mode;		/*  who now uses IRQ - 1=AI1 int, 2=AI1 dma, 3=AI3 int, 4AI3 dma */
@@ -701,8 +700,7 @@ static irqreturn_t interrupt_pcl818(int irq, void *d)
 
 	outb(0, dev->iobase + PCL818_CLRINT);	/* clear INT request */
 
-	if ((!dev->irq) || (!devpriv->irq_free) || (!devpriv->irq_blocked)
-	    || (!devpriv->ai_mode)) {
+	if (!dev->irq || !devpriv->irq_blocked || !devpriv->ai_mode) {
 		comedi_error(dev, "bad IRQ!");
 		return IRQ_NONE;
 	}
@@ -1230,10 +1228,8 @@ static int pcl818_attach(struct comedi_device *dev, struct comedi_devconfig *it)
 	if ((1 << it->options[1]) & board->IRQbits) {
 		ret = request_irq(it->options[1], interrupt_pcl818, 0,
 				  dev->board_name, dev);
-		if (ret == 0) {
+		if (ret == 0)
 			dev->irq = it->options[1];
-			devpriv->irq_free = 1;
-		}
 	}
 
 	devpriv->irq_blocked = 0;	/* number of subdevice which use IRQ */
@@ -1242,7 +1238,7 @@ static int pcl818_attach(struct comedi_device *dev, struct comedi_devconfig *it)
 	/* grab our DMA */
 	dma = 0;
 	devpriv->dma = dma;
-	if (!devpriv->irq_free)
+	if (!dev->irq)
 		goto no_dma;	/* if we haven't IRQ, we can't use DMA */
 	if (board->DMAbits != 0) {	/* board support DMA */
 		dma = it->options[2];
-- 
1.8.4.4