[PATCH 6/9] staging/easycap: Add option to set the hardware audio gain
Mike Thomas
rmthomas at sciolus.org
Sun Nov 7 20:05:51 UTC 2010
A new module parameter adjusts the gain of the AC'97 audio chip, if
one is present. Attenuation as well as amplification should be possible
according to the datasheet, but attenuation seems not to work yet.
Signed-off-by: Mike Thomas <rmthomas at sciolus.org>
---
drivers/staging/easycap/easycap_debug.h | 1 +
drivers/staging/easycap/easycap_ioctl.c | 14 +++-
drivers/staging/easycap/easycap_low.c | 120 ++++++++++++++++++++-----------
drivers/staging/easycap/easycap_main.c | 8 ++-
4 files changed, 96 insertions(+), 47 deletions(-)
diff --git a/drivers/staging/easycap/easycap_debug.h b/drivers/staging/easycap/easycap_debug.h
index a4dcd7d..7042fe8 100644
--- a/drivers/staging/easycap/easycap_debug.h
+++ b/drivers/staging/easycap/easycap_debug.h
@@ -25,3 +25,4 @@
*/
/*****************************************************************************/
extern int debug;
+extern int gain;
diff --git a/drivers/staging/easycap/easycap_ioctl.c b/drivers/staging/easycap/easycap_ioctl.c
index 3fe1385..7c46cb2 100644
--- a/drivers/staging/easycap/easycap_ioctl.c
+++ b/drivers/staging/easycap/easycap_ioctl.c
@@ -873,18 +873,26 @@ i1 = 0;
while (0xFFFFFFFF != easycap_control[i1].id) {
if (V4L2_CID_AUDIO_VOLUME == easycap_control[i1].id) {
if ((easycap_control[i1].minimum > value) || \
- (easycap_control[i1].maximum < value))
+ (easycap_control[i1].maximum < value))
value = easycap_control[i1].default_value;
+ if ((easycap_control[i1].minimum <= peasycap->volume) && \
+ (easycap_control[i1].maximum >= \
+ peasycap->volume)) {
+ if (peasycap->volume == value) {
+ SAM("unchanged volume at 0x%02X\n", value);
+ return 0;
+ }
+ }
peasycap->volume = value;
mood = (16 > peasycap->volume) ? 16 : \
((31 < peasycap->volume) ? 31 : \
(__s8) peasycap->volume);
if (!audio_gainset(peasycap->pusb_device, mood)) {
- SAM("adjusting volume to 0x%01X\n", mood);
+ SAM("adjusting volume to 0x%02X\n", mood);
return 0;
} else {
SAM("WARNING: failed to adjust volume to " \
- "0x%1X\n", mood);
+ "0x%2X\n", mood);
return -ENOENT;
}
break;
diff --git a/drivers/staging/easycap/easycap_low.c b/drivers/staging/easycap/easycap_low.c
index 4badef2..7d778ba 100644
--- a/drivers/staging/easycap/easycap_low.c
+++ b/drivers/staging/easycap/easycap_low.c
@@ -988,9 +988,9 @@ if (NULL == peasycap)
pusb_device = peasycap->pusb_device;
if (NULL == pusb_device)
- return -EFAULT;
+ return -ENODEV;
-JOT(8, "%02X %02X %02X %02X %02X %02X %02X %02X\n", \
+JOM(8, "%02X %02X %02X %02X %02X %02X %02X %02X\n", \
requesttype, request, \
(0x00FF & value_unmute), \
(0xFF00 & value_unmute) >> 8, \
@@ -1029,41 +1029,25 @@ if (rc != (int)length)
* THE UPPER BYTE SEEMS TO HAVE NO EFFECT.
*/
/*--------------------------------------------------------------------------*/
-
SET(pusb_device, 0x0500, 0x0094);
-
SET(pusb_device, 0x0500, 0x008C);
-
SET(pusb_device, 0x0506, 0x0001);
SET(pusb_device, 0x0507, 0x0000);
-
id1 = read_vt(pusb_device, 0x007C);
id2 = read_vt(pusb_device, 0x007E);
-SAY("0x%04X:0x%04X is audio vendor id\n", id1, id2);
-
+SAM("0x%04X:0x%04X is audio vendor id\n", id1, id2);
/*---------------------------------------------------------------------------*/
/*
-* SELECT AUDIO SOURCE "LINE IN" AND SET DEFAULT GAIN TO 0 dB.
-*
-* THESE COMMANDS SEEM TO BE ACCEPTED (THOUGH POSSIBLY IGNORED) EVEN WHEN
-* THERE IS NO SEPARATE AUDIO CHIP PRESENT.
+ * SELECT AUDIO SOURCE "LINE IN" AND SET THE AUDIO GAIN.
*/
/*---------------------------------------------------------------------------*/
-
-write_vt(pusb_device, 0x0002, 0x8000);
-write_vt(pusb_device, 0x001C, 0x8000);
-
-write_vt(pusb_device, 0x000E, 0x0000);
-write_vt(pusb_device, 0x0010, 0x0000);
-write_vt(pusb_device, 0x0012, 0x8000);
-write_vt(pusb_device, 0x0016, 0x0000);
-
-write_vt(pusb_device, 0x001A, 0x0404);
-write_vt(pusb_device, 0x0002, 0x0000);
-write_vt(pusb_device, 0x001C, 0x0000);
-
+if (31 < gain)
+ gain = 31;
+if (0 > gain)
+ gain = 0;
+if (0 != audio_gainset(pusb_device, (__s8)gain))
+ SAY("ERROR: audio_gainset() failed\n");
check_vt(pusb_device);
-
return 0;
}
/*****************************************************************************/
@@ -1096,17 +1080,23 @@ if (0 > igot)
if (0x8000 & igot)
SAY("register 0x%02X muted\n", 0x12);
+igot = read_vt(pusb_device, 0x0014);
+if (0 > igot)
+ SAY("ERROR: failed to read VT1612A register 0x14\n");
+if (0x8000 & igot)
+ SAY("register 0x%02X muted\n", 0x14);
+
igot = read_vt(pusb_device, 0x0016);
if (0 > igot)
SAY("ERROR: failed to read VT1612A register 0x16\n");
if (0x8000 & igot)
SAY("register 0x%02X muted\n", 0x16);
-igot = read_vt(pusb_device, 0x001A);
+igot = read_vt(pusb_device, 0x0018);
if (0 > igot)
- SAY("ERROR: failed to read VT1612A register 0x1A\n");
+ SAY("ERROR: failed to read VT1612A register 0x18\n");
if (0x8000 & igot)
- SAY("register 0x%02X muted\n", 0x1A);
+ SAY("register 0x%02X muted\n", 0x18);
igot = read_vt(pusb_device, 0x001C);
if (0 > igot)
@@ -1118,14 +1108,18 @@ return 0;
}
/*****************************************************************************/
/*---------------------------------------------------------------------------*/
-/*
- * NOTE: THIS DOES INCREASE THE VOLUME DRAMATICALLY:
- * audio_gainset(pusb_device, 0x000F);
+/* NOTE: THIS DOES INCREASE THE VOLUME DRAMATICALLY:
+ * audio_gainset(pusb_device, 0x000F);
*
- * IF 16<loud<31 VT1621A REGISTER 0x1C IS SET FOR POSITIVE GAIN.
- * IF loud<=16 VT1621A REGISTER 0x1C IS SET FOR ZERO GAIN.
- * THERE IS NEVER ANY (ADDITIONAL) ATTENUATION.
- */
+ * loud dB register 0x10 dB register 0x1C dB total
+ * 0 -34.5 0 -34.5
+ * .. .... . ....
+ * 15 10.5 0 10.5
+ * 16 12.0 0 12.0
+ * 17 12.0 1.5 13.5
+ * .. .... .... ....
+ * 31 12.0 22.5 34.5
+*/
/*---------------------------------------------------------------------------*/
int
audio_gainset(struct usb_device *pusb_device, __s8 loud)
@@ -1134,25 +1128,65 @@ int igot;
__u8 u8;
__u16 mute;
-if (16 > loud)
- loud = 16;
-u8 = 0x000F & (__u8)(loud - 16);
+if ((struct usb_device *)NULL == pusb_device)
+ return -ENODEV;
+if (0 > loud)
+ loud = 0;
+if (31 < loud)
+ loud = 31;
write_vt(pusb_device, 0x0002, 0x8000);
+/*---------------------------------------------------------------------------*/
+igot = read_vt(pusb_device, 0x000E);
+if (0 > igot) {
+ SAY("ERROR: failed to read VT1612A register 0x0E\n");
+ mute = 0x0000;
+} else
+ mute = 0x8000 & ((unsigned int)igot);
+mute = 0;
+if (16 > loud)
+ u8 = 0x01 | (0x001F & (((__u8)(15 - loud)) << 1));
+else
+ u8 = 0;
+
+JOT(8, "0x%04X=(mute|u8) for VT1612A register 0x0E\n", mute | u8);
+write_vt(pusb_device, 0x000E, (mute | u8));
+/*---------------------------------------------------------------------------*/
+igot = read_vt(pusb_device, 0x0010);
+if (0 > igot) {
+ SAY("ERROR: failed to read VT1612A register 0x10\n");
+ mute = 0x0000;
+} else
+ mute = 0x8000 & ((unsigned int)igot);
+mute = 0;
+
+JOT(8, "0x%04X=(mute|u8|(u8<<8)) for VT1612A register 0x10,...0x18\n", \
+ mute | u8 | (u8 << 8));
+write_vt(pusb_device, 0x0010, (mute | u8 | (u8 << 8)));
+write_vt(pusb_device, 0x0012, (mute | u8 | (u8 << 8)));
+write_vt(pusb_device, 0x0014, (mute | u8 | (u8 << 8)));
+write_vt(pusb_device, 0x0016, (mute | u8 | (u8 << 8)));
+write_vt(pusb_device, 0x0018, (mute | u8 | (u8 << 8)));
+/*---------------------------------------------------------------------------*/
igot = read_vt(pusb_device, 0x001C);
if (0 > igot) {
SAY("ERROR: failed to read VT1612A register 0x1C\n");
mute = 0x0000;
} else
mute = 0x8000 & ((unsigned int)igot);
+mute = 0;
-JOT(8, "0x%04X=(mute|u8|(u8<<8))\n", mute | u8 | (u8 << 8));
+if (16 <= loud)
+ u8 = 0x000F & (__u8)(loud - 16);
+else
+ u8 = 0;
-write_vt(pusb_device, 0x001C, 0x8000);
+JOT(8, "0x%04X=(mute|u8|(u8<<8)) for VT1612A register 0x1C\n", \
+ mute | u8 | (u8 << 8));
write_vt(pusb_device, 0x001C, (mute | u8 | (u8 << 8)));
+write_vt(pusb_device, 0x001A, 0x0404);
write_vt(pusb_device, 0x0002, 0x0000);
-
return 0;
}
/*****************************************************************************/
@@ -1161,6 +1195,8 @@ audio_gainget(struct usb_device *pusb_device)
{
int igot;
+if (NULL == pusb_device)
+ return -ENODEV;
igot = read_vt(pusb_device, 0x001C);
if (0 > igot)
SAY("ERROR: failed to read VT1612A register 0x1C\n");
diff --git a/drivers/staging/easycap/easycap_main.c b/drivers/staging/easycap/easycap_main.c
index 21450e8..ee5c8d9 100644
--- a/drivers/staging/easycap/easycap_main.c
+++ b/drivers/staging/easycap/easycap_main.c
@@ -34,8 +34,10 @@
int debug;
int bars;
+int gain = 16;
module_param(debug, int, S_IRUGO | S_IWUSR);
module_param(bars, int, S_IRUGO | S_IWUSR);
+module_param(gain, int, S_IRUGO | S_IWUSR);
/*---------------------------------------------------------------------------*/
/*
@@ -4770,7 +4772,8 @@ easycap_module_init(void)
int result;
SAY("========easycap=======\n");
-JOT(4, "begins. %i=debug %i=bars\n", debug, bars);
+JOT(4, "begins. %i=debug %i=bars %i=gain\n", debug, bars, \
+ gain);
SAY("version: " EASYCAP_DRIVER_VERSION "\n");
/*---------------------------------------------------------------------------*/
/*
@@ -4811,8 +4814,9 @@ MODULE_AUTHOR("R.M. Thomas <rmthomas at sciolus.org>");
MODULE_DESCRIPTION(EASYCAP_DRIVER_DESCRIPTION);
MODULE_VERSION(EASYCAP_DRIVER_VERSION);
#if defined(EASYCAP_DEBUG)
-MODULE_PARM_DESC(debug, "Debug level: 0 (default),1,2,...,9");
+MODULE_PARM_DESC(debug, "Debug level: 0 (default),1,2,...");
#endif /*EASYCAP_DEBUG*/
MODULE_PARM_DESC(bars, \
"Testcard bars on input signal failure: 0=>no, 1=>yes(default)");
+MODULE_PARM_DESC(gain, "Audio gain: 0,...,16(default),...31");
/*****************************************************************************/
--
1.5.6.5
More information about the devel
mailing list