[PATCH 385/524] staging: rtl8192su: various updates
Greg Kroah-Hartman
gregkh at suse.de
Thu Aug 5 22:22:48 UTC 2010
From: Florian Schilhabel <florian.c.schilhabel at googlemail.com>
Signed-off-by: Florian Schilhabel <florian.c.schilhabel at googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh at suse.de>
---
.../staging/rtl8192su/ieee80211/ieee80211_r8192s.h | 43 +++--
drivers/staging/rtl8192su/r8192S_firmware.c | 26 ++-
drivers/staging/rtl8192su/r8192S_firmware.h | 100 ++++++-----
drivers/staging/rtl8192su/r8192S_hw.h | 83 +++++----
drivers/staging/rtl8192su/r8192S_phy.c | 183 +++++++++----------
5 files changed, 232 insertions(+), 203 deletions(-)
diff --git a/drivers/staging/rtl8192su/ieee80211/ieee80211_r8192s.h b/drivers/staging/rtl8192su/ieee80211/ieee80211_r8192s.h
index 1824cda..7e7fbb2 100644
--- a/drivers/staging/rtl8192su/ieee80211/ieee80211_r8192s.h
+++ b/drivers/staging/rtl8192su/ieee80211/ieee80211_r8192s.h
@@ -339,28 +339,39 @@ enum {
};
/* Firmware related CMD IO. */
-typedef enum _FW_CMD_IO_TYPE {
- FW_CMD_DIG_ENABLE = 0, /* for DIG DM */
+typedef enum _FW_CMD_IO_TYPE{
+ FW_CMD_DIG_ENABLE = 0, /* for DIG DM */
FW_CMD_DIG_DISABLE = 1,
FW_CMD_DIG_HALT = 2,
FW_CMD_DIG_RESUME = 3,
- FW_CMD_HIGH_PWR_ENABLE = 4, /* for High Power DM */
+ FW_CMD_HIGH_PWR_ENABLE = 4, /* for DIG DM */
FW_CMD_HIGH_PWR_DISABLE = 5,
- FW_CMD_RA_RESET = 6, /* for Rate adaptive DM */
- FW_CMD_RA_ACTIVE = 7,
- FW_CMD_RA_REFRESH_N = 8,
- FW_CMD_RA_REFRESH_BG = 9,
- FW_CMD_IQK_ENABLE = 10, /* for FW supported IQK */
- FW_CMD_TXPWR_TRACK_ENABLE = 11, /* Tx power tracking switch */
- FW_CMD_TXPWR_TRACK_DISABLE = 12,/* Tx power tracking switch */
- FW_CMD_PAUSE_DM_BY_SCAN = 13,
- FW_CMD_RESUME_DM_BY_SCAN = 14,
- FW_CMD_MID_HIGH_PWR_ENABLE = 15,
+ FW_CMD_RA_RESET = 6, /* for DIG DM */
+ FW_CMD_RA_ACTIVE= 7,
+ FW_CMD_RA_REFRESH_N= 8,
+ FW_CMD_RA_REFRESH_BG= 9,
+ FW_CMD_RA_INIT= 10, /* for FW supported IQK */
+ FW_CMD_IQK_ENABLE = 11, /* Tx power tracking switch */
+ FW_CMD_TXPWR_TRACK_ENABLE = 12, /* Tx power tracking switch */
+ FW_CMD_TXPWR_TRACK_DISABLE = 13,
+ FW_CMD_TXPWR_TRACK_THERMAL = 14,
+ FW_CMD_PAUSE_DM_BY_SCAN = 15,
/* indicate firmware that driver enters LPS, for PS-Poll hardware bug */
- FW_CMD_LPS_ENTER = 16,
+ FW_CMD_RESUME_DM_BY_SCAN = 16,
/* indicate firmware that driver leave LPS */
- FW_CMD_LPS_LEAVE = 17,
-} FW_CMD_IO_TYPE;
+ FW_CMD_RA_REFRESH_N_COMB = 17,
+ FW_CMD_RA_REFRESH_BG_COMB = 18,
+ FW_CMD_ANTENNA_SW_ENABLE = 19,
+ FW_CMD_ANTENNA_SW_DISABLE = 20,
+ FW_CMD_TX_FEEDBACK_CCX_ENABLE = 21,
+ FW_CMD_LPS_ENTER = 22,
+ FW_CMD_LPS_LEAVE = 23,
+ FW_CMD_DIG_MODE_SS = 24,
+ FW_CMD_DIG_MODE_FA = 25,
+ FW_CMD_ADD_A2_ENTRY = 26,
+ FW_CMD_CTRL_DM_BY_DRIVER = 27,
+ FW_CMD_CTRL_DM_BY_DRIVER_NEW = 28,
+}FW_CMD_IO_TYPE,*PFW_CMD_IO_TYPE;
#define RT_MAX_LD_SLOT_NUM 10
struct rt_link_detect {
diff --git a/drivers/staging/rtl8192su/r8192S_firmware.c b/drivers/staging/rtl8192su/r8192S_firmware.c
index 5036d54..db0d2d5 100644
--- a/drivers/staging/rtl8192su/r8192S_firmware.c
+++ b/drivers/staging/rtl8192su/r8192S_firmware.c
@@ -1,16 +1,22 @@
-/**************************************************************************************************
- * Procedure: Init boot code/firmware code/data session
+/******************************************************************************
+ * Copyright(c) 2008 - 2010 Realtek Corporation. All rights reserved.
*
- * Description: This routine will intialize firmware. If any error occurs during the initialization
- * process, the routine shall terminate immediately and return fail.
- * NIC driver should call NdisOpenFile only from MiniportInitialize.
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
*
- * Arguments: The pointer of the adapter
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110, USA
+ *
+ * The full GNU General Public License is included in this distribution in the
+ * file called LICENSE.
+ *
+ * Contact Information:
+ * wlanfae <wlanfae at realtek.com>
+******************************************************************************/
- * Returns:
- * NDIS_STATUS_FAILURE - the following initialization process should be terminated
- * NDIS_STATUS_SUCCESS - if firmware initialization process success
-**************************************************************************************************/
#include "r8192U.h"
#include "r8192S_firmware.h"
#include <linux/unistd.h>
diff --git a/drivers/staging/rtl8192su/r8192S_firmware.h b/drivers/staging/rtl8192su/r8192S_firmware.h
index 2c2cf80..7f268a8 100644
--- a/drivers/staging/rtl8192su/r8192S_firmware.h
+++ b/drivers/staging/rtl8192su/r8192S_firmware.h
@@ -1,44 +1,32 @@
+/******************************************************************************
+ * Copyright(c) 2008 - 2010 Realtek Corporation. All rights reserved.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110, USA
+ *
+ * The full GNU General Public License is included in this distribution in the
+ * file called LICENSE.
+ *
+ * Contact Information:
+ * wlanfae <wlanfae at realtek.com>
+******************************************************************************/
#ifndef __INC_FIRMWARE_H
#define __INC_FIRMWARE_H
-//#define RTL8190_CPU_START_OFFSET 0x80
-/* TODO: this definition is TBD */
-//#define USB_HWDESC_HEADER_LEN 0
-
-/* It should be double word alignment */
-//#if DEV_BUS_TYPE==PCI_INTERFACE
-//#define GET_COMMAND_PACKET_FRAG_THRESHOLD(v) 4*(v/4) - 8
-//#else
-//#define GET_COMMAND_PACKET_FRAG_THRESHOLD(v) (4*(v/4) - 8 - USB_HWDESC_HEADER_LEN)
-//#endif
-
-//typedef enum _firmware_init_step{
-// FW_INIT_STEP0_BOOT = 0,
-// FW_INIT_STEP1_MAIN = 1,
-// FW_INIT_STEP2_DATA = 2,
-//}firmware_init_step_e;
-
-//typedef enum _DESC_PACKET_TYPE{
-// DESC_PACKET_TYPE_INIT = 0,
-// DESC_PACKET_TYPE_NORMAL = 1,
-//}DESC_PACKET_TYPE;
-#define RTL8192S_FW_PKT_FRAG_SIZE 0xFF00 // 64K
-
-
#define RTL8190_MAX_FIRMWARE_CODE_SIZE 64000 //64k
#define MAX_FIRMWARE_CODE_SIZE 0xFF00 // Firmware Local buffer size.
#define RTL8190_CPU_START_OFFSET 0x80
-
+#define RTL8192S_FW_PKT_FRAG_SIZE 0x4000
#define GET_COMMAND_PACKET_FRAG_THRESHOLD(v) (4*(v/4) - 8 - USB_HWDESC_HEADER_LEN)
-//typedef enum _DESC_PACKET_TYPE{
-// DESC_PACKET_TYPE_INIT = 0,
-// DESC_PACKET_TYPE_NORMAL = 1,
-//}DESC_PACKET_TYPE;
-// Forward declaration.
-//typedef struct _ADAPTER ADAPTER, *PADAPTER;
#ifdef RTL8192S
typedef enum _firmware_init_step{
FW_INIT_STEP0_IMEM = 0,
@@ -64,17 +52,8 @@ typedef enum _opt_rst_type{
OPT_FIRMWARE_RESET = 1,
}opt_rst_type_e;
-/*typedef enum _FIRMWARE_STATUS{
- FW_STATUS_0_INIT = 0,
- FW_STATUS_1_MOVE_BOOT_CODE = 1,
- FW_STATUS_2_MOVE_MAIN_CODE = 2,
- FW_STATUS_3_TURNON_CPU = 3,
- FW_STATUS_4_MOVE_DATA_CODE = 4,
- FW_STATUS_5_READY = 5,
-}FIRMWARE_STATUS;
-*/
//--------------------------------------------------------------------------------
-// RTL8192S Firmware related, Revised by Roger, 2008.12.18.
+// RTL8192S Firmware related
//--------------------------------------------------------------------------------
typedef struct _RT_8192S_FIRMWARE_PRIV { //8-bytes alignment required
@@ -181,7 +160,6 @@ typedef enum _FIRMWARE_8192S_STATUS{
typedef struct _rt_firmware{
PRT_8192S_FIRMWARE_HDR pFwHeader;
FIRMWARE_8192S_STATUS FWStatus;
- u16 FirmwareVersion;
u8 FwIMEM[RTL8190_MAX_FIRMWARE_CODE_SIZE];
u8 FwEMEM[RTL8190_MAX_FIRMWARE_CODE_SIZE];
u32 FwIMEMLen;
@@ -189,11 +167,43 @@ typedef struct _rt_firmware{
u8 szFwTmpBuffer[164000];
u32 szFwTmpBufferLen;
u16 CmdPacketFragThresold;
+ u16 FirmwareVersion;
}rt_firmware, *prt_firmware;
-//typedef struct _RT_FIRMWARE_INFO_8192SU{
-// u8 szInfo[16];
-//}RT_FIRMWARE_INFO_8192SU, *PRT_FIRMWARE_INFO_8192SU;
+#define FW_DIG_ENABLE_CTL BIT0
+#define FW_HIGH_PWR_ENABLE_CTL BIT1
+#define FW_SS_CTL BIT2
+#define FW_RA_INIT_CTL BIT3
+#define FW_RA_BG_CTL BIT4
+#define FW_RA_N_CTL BIT5
+#define FW_PWR_TRK_CTL BIT6
+#define FW_IQK_CTL BIT7
+#define FW_ANTENNA_SW BIT8
+#define FW_DISABLE_ALL_DM 0
+
+#define FW_PWR_TRK_PARAM_CLR 0x0000ffff
+#define FW_RA_PARAM_CLR 0xffff0000
+
+#define FW_CMD_IO_CLR(_pdev, _Bit) \
+ udelay(1000); \
+ ((struct r8192_priv *)ieee80211_priv(_pdev))->FwCmdIOMap &= (~_Bit);
+
+#define FW_CMD_IO_UPDATE(_pdev, _val) \
+ ((struct r8192_priv *)ieee80211_priv(_pdev))->FwCmdIOMap = _val;
+
+#define FW_CMD_IO_SET(_pdev, _val) \
+ write_nic_word(_pdev, LBUS_MON_ADDR, (u16)_val); \
+ FW_CMD_IO_UPDATE(_pdev, _val);
+
+#define FW_CMD_PARA_SET(_pdev, _val) \
+ write_nic_dword(_pdev, LBUS_ADDR_MASK, _val); \
+ ((struct r8192_priv *)ieee80211_priv(_pdev))->FwCmdIOParam = _val;
+
+#define FW_CMD_IO_QUERY(_pdev) (u16)(((struct r8192_priv *)ieee80211_priv(_pdev))->FwCmdIOMap)
+#define FW_CMD_IO_PARA_QUERY(_pdev) (u32)(((struct r8192_priv *)ieee80211_priv(_pdev))->FwCmdIOParam)
+
+
+
bool FirmwareDownload92S(struct net_device *dev);
#endif
diff --git a/drivers/staging/rtl8192su/r8192S_hw.h b/drivers/staging/rtl8192su/r8192S_hw.h
index a28e524..e62b79d 100644
--- a/drivers/staging/rtl8192su/r8192S_hw.h
+++ b/drivers/staging/rtl8192su/r8192S_hw.h
@@ -1,25 +1,22 @@
-/*****************************************************************************
- * Copyright(c) 2008, RealTEK Technology Inc. All Right Reserved.
+/******************************************************************************
+ * Copyright(c) 2008 - 2010 Realtek Corporation. All rights reserved.
*
- * Module: __INC_HAL8192SEREG_H
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
*
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110, USA
*
- * Note: 1. Define Mac register address and corresponding bit mask map
- * 2. CCX register
- * 3. Backward compatible register with useless address.
- * 4. Define 92SU required register address and definition.
+ * The full GNU General Public License is included in this distribution in the
+ * file called LICENSE.
*
- *
- * Export: Constants, macro, functions(API), global variables(None).
- *
- * Abbrev:
- *
- * History:
- * Data Who Remark
- * 08/07/2007 MHC 1. Porting from 9x series PHYCFG.h.
- * 2. Reorganize code architecture.
- *
- *****************************************************************************/
+ * Contact Information:
+ * wlanfae <wlanfae at realtek.com>
+******************************************************************************/
+
#ifndef R8192S_HW
#define R8192S_HW
@@ -58,10 +55,10 @@ typedef enum _BaseBand_Config_Type{
#define RTL8187_REQ_SET_REGS 0x05
#define MAX_TX_URB 5
-#define MAX_RX_URB 16
+#define MAX_RX_URB 8
#define R8180_MAX_RETRY 255
-#define RX_URB_SIZE 9100
+#define RX_URB_SIZE 0x4000
#define BB_ANTATTEN_CHAN14 0x0c
#define BB_ANTENNA_B 0x40
@@ -122,7 +119,6 @@ typedef enum _BaseBand_Config_Type{
#define MSR_LINK_ENEDCA (1<<4)
-//#define Cmd9346CR_9356SEL (1<<4)
#define EPROM_CMD_RESERVED_MASK (1<<5)
#define EPROM_CMD_OPERATING_MODE_SHIFT 6
#define EPROM_CMD_OPERATING_MODE_MASK ((1<<7)|(1<<6))
@@ -1230,17 +1226,18 @@ Default: 00b.
#define EEPROM_CHANNEL_PLAN_GLOBAL_DOMAIN 0x9
#define EEPROM_CHANNEL_PLAN_WORLD_WIDE_13 0xA
#define EEPROM_CHANNEL_PLAN_BY_HW_MASK 0x80
+#define EEPROM_CID_DEFAULT 0x0
+#define EEPROM_CID_ALPHA 0x1
+#define EEPROM_CID_Senao 0x3
+#define EEPROM_CID_CAMEO 0X8
+#define EEPROM_CID_SITECOM 0x9
+#define EEPROM_CID_COREGA 0xB
+#define EEPROM_CID_EDIMAX_BELKIN 0xC
+#define EEPROM_CID_SERCOMM_BELKIN 0xE
+#define EEPROM_CID_CAMEO1 0xF
+#define EEPROM_CID_WHQL 0xFE
+#define EEPROM_CID_NetCore 0x5
-#define EEPROM_CID_DEFAULT 0x0
-#define EEPROM_CID_ALPHA 0x1
-#define EEPROM_CID_CAMEO 0X8
-#define EEPROM_CID_SITECOM 0x9
-
-//#define EEPROM_CID_RUNTOP 0x2
-//#define EEPROM_CID_Senao 0x3
-//#define EEPROM_CID_TOSHIBA 0x4
-//#define EEPROM_CID_NetCore 0x5
-#define EEPROM_CID_WHQL 0xFE // added by chiyoko for dtm, 20090108
//-----------------------------------------------------------------
// 0x2c0 FW Command Control register definition, added by Roger, 2008.11.27.
@@ -1253,18 +1250,32 @@ Default: 00b.
#define FW_HIGH_PWR_ENABLE 0xfd000009
#define FW_TXPWR_TRACK_ENABLE 0xfd000017
#define FW_TXPWR_TRACK_DISABLE 0xfd000018
-#define FW_RA_RESET 0xfd0000af
-#define FW_RA_ACTIVE 0xfd0000a6
+#define FW_TXPWR_TRACK_THERMAL 0xfd000019
+#define FW_RA_INIT 0xfd000026
+#define FW_RA_IOT_BG_COMB 0xfd000030
+#define FW_RA_IOT_N_COMB 0xfd000031
#define FW_RA_REFRESH 0xfd0000a0
-#define FW_RA_ENABLE_BG 0xfd0000ac
+#define FW_RA_DISABLE 0xfd0000a4
+#define FW_RA_ACTIVE 0xfd0000a6
+#define FW_RA_DISABLE_RSSI_MASK 0xfd0000ac
+#define FW_RA_ENABLE_RSSI_MASK 0xfd0000ad
+#define FW_RA_RESET 0xfd0000af
+#define FW_DM_DISABLE 0xfd00aa00
#define FW_IQK_ENABLE 0xf0000020
#define FW_IQK_SUCCESS 0x0000dddd
#define FW_IQK_FAIL 0x0000ffff
#define FW_OP_FAILURE 0xffffffff
-#define FW_DM_DISABLE 0xfd00aa00
+#define FW_TX_FEEDBACK_NONE 0xfb000000
+#define FW_TX_FEEDBACK_DTM_ENABLE (FW_TX_FEEDBACK_NONE | 0x1)
+#define FW_TX_FEEDBACK_CCX_ENABLE (FW_TX_FEEDBACK_NONE | 0x2)
#define FW_BB_RESET_ENABLE 0xff00000d
#define FW_BB_RESET_DISABLE 0xff00000e
-
+#define FW_LPS_ENTER 0xfe000010
+#define FW_LPS_LEAVE 0xfe000011
+#define FW_INDIRECT_READ 0xf2000000
+#define FW_INDIRECT_WRITE 0xf2000001
+#define FW_TXANT_SWITCH_ENABLE 0xfd000023
+#define FW_TXANT_SWITCH_DISABLE 0xfd000024
//
//--------------92SU require delete or move to other place later
//
diff --git a/drivers/staging/rtl8192su/r8192S_phy.c b/drivers/staging/rtl8192su/r8192S_phy.c
index fb7d676..a5fc2d1 100644
--- a/drivers/staging/rtl8192su/r8192S_phy.c
+++ b/drivers/staging/rtl8192su/r8192S_phy.c
@@ -3485,9 +3485,10 @@ void ChkFwCmdIoDone(struct net_device* dev)
//
void phy_SetFwCmdIOCallback(struct net_device* dev)
{
- u32 input;
- static u32 ScanRegister;
struct r8192_priv *priv = ieee80211_priv(dev);
+ PRT_HIGH_THROUGHPUT pHTInfo = priv->ieee80211->pHTInfo;
+ rt_firmware *pFirmware = priv->pFirmware;
+ u32 input, CurrentAID = 0;;
if(!priv->up)
{
RT_TRACE(COMP_CMD, "SetFwCmdIOTimerCallback(): driver is going to unload\n");
@@ -3496,61 +3497,22 @@ void phy_SetFwCmdIOCallback(struct net_device* dev)
RT_TRACE(COMP_CMD, "--->SetFwCmdIOTimerCallback(): Cmd(%#x), SetFwCmdInProgress(%d)\n", priv->CurrentFwCmdIO, priv->SetFwCmdInProgress);
- switch(priv->CurrentFwCmdIO)
+ if(pFirmware->FirmwareVersion >= 0x34)
{
- case FW_CMD_HIGH_PWR_ENABLE:
- if((priv->ieee80211->pHTInfo->IOTAction & HT_IOT_ACT_DISABLE_HIGH_POWER)==0)
- write_nic_dword(dev, WFM5, FW_HIGH_PWR_ENABLE);
- break;
-
- case FW_CMD_HIGH_PWR_DISABLE:
- write_nic_dword(dev, WFM5, FW_HIGH_PWR_DISABLE);
- break;
-
- case FW_CMD_DIG_RESUME:
- write_nic_dword(dev, WFM5, FW_DIG_RESUME);
- break;
-
- case FW_CMD_DIG_HALT:
- write_nic_dword(dev, WFM5, FW_DIG_HALT);
- break;
-
- //
- // <Roger_Notes> The following FW CMD IO was combined into single operation
- // (i.e., to prevent number of system workitem out of resource!!).
- // 2008.12.04.
- //
- case FW_CMD_RESUME_DM_BY_SCAN:
- RT_TRACE(COMP_CMD, "[FW CMD] Set HIGHPWR enable and DIG resume!!\n");
- if((priv->ieee80211->pHTInfo->IOTAction & HT_IOT_ACT_DISABLE_HIGH_POWER)==0)
- {
- write_nic_dword(dev, WFM5, FW_HIGH_PWR_ENABLE); //break;
- ChkFwCmdIoDone(dev);
- }
- write_nic_dword(dev, WFM5, FW_DIG_RESUME);
- break;
-
- case FW_CMD_PAUSE_DM_BY_SCAN:
- RT_TRACE(COMP_CMD, "[FW CMD] Set HIGHPWR disable and DIG halt!!\n");
- write_nic_dword(dev, WFM5, FW_HIGH_PWR_DISABLE); //break;
- ChkFwCmdIoDone(dev);
- write_nic_dword(dev, WFM5, FW_DIG_HALT);
+ switch(priv->CurrentFwCmdIO)
+ {
+ case FW_CMD_RA_REFRESH_N:
+ priv->CurrentFwCmdIO = FW_CMD_RA_REFRESH_N_COMB;
break;
-
- //
- // <Roger_Notes> The following FW CMD IO should be checked
- // (i.e., workitem schedule timing issue!!).
- // 2008.12.04.
- //
- case FW_CMD_DIG_DISABLE:
- RT_TRACE(COMP_CMD, "[FW CMD] Set DIG disable!!\n");
- write_nic_dword(dev, WFM5, FW_DIG_DISABLE);
+ case FW_CMD_RA_REFRESH_BG:
+ priv->CurrentFwCmdIO = FW_CMD_RA_REFRESH_BG_COMB;
break;
-
- case FW_CMD_DIG_ENABLE:
- RT_TRACE(COMP_CMD, "[FW CMD] Set DIG enable!!\n");
- write_nic_dword(dev, WFM5, FW_DIG_ENABLE);
+ default:
break;
+ }
+ }
+ switch(priv->CurrentFwCmdIO)
+ {
case FW_CMD_RA_RESET:
write_nic_dword(dev, WFM5, FW_RA_RESET);
@@ -3561,82 +3523,111 @@ void phy_SetFwCmdIOCallback(struct net_device* dev)
break;
case FW_CMD_RA_REFRESH_N:
- RT_TRACE(COMP_CMD, "[FW CMD] Set RA refresh!! N\n");
- if(priv->ieee80211->pHTInfo->IOTRaFunc & HT_IOT_RAFUNC_DISABLE_ALL)
+ RT_TRACE(COMP_CMD, "[FW CMD] Set RA n refresh!!\n");
+ if(pHTInfo->IOTRaFunc & HT_IOT_RAFUNC_DISABLE_ALL)
input = FW_RA_REFRESH;
else
- input = FW_RA_REFRESH | (priv->ieee80211->pHTInfo->IOTRaFunc << 8);
+ input = FW_RA_REFRESH | (pHTInfo->IOTRaFunc << 8);
write_nic_dword(dev, WFM5, input);
+ ChkFwCmdIoDone(dev);
+ write_nic_dword(dev, WFM5, FW_RA_ENABLE_RSSI_MASK);
+ ChkFwCmdIoDone(dev);
break;
case FW_CMD_RA_REFRESH_BG:
- RT_TRACE(COMP_CMD, "[FW CMD] Set RA refresh!! B/G\n");
+ RT_TRACE(COMP_CMD, "[FW CMD] Set RA BG refresh!!\n");
write_nic_dword(dev, WFM5, FW_RA_REFRESH);
ChkFwCmdIoDone(dev);
- write_nic_dword(dev, WFM5, FW_RA_ENABLE_BG);
+ write_nic_dword(dev, WFM5, FW_RA_DISABLE_RSSI_MASK);
+ ChkFwCmdIoDone(dev);
+ break;
+
+ case FW_CMD_RA_REFRESH_N_COMB:
+ RT_TRACE(COMP_CMD, "[FW CMD] Set RA n Combo refresh!!\n");
+ if(pHTInfo->IOTRaFunc & HT_IOT_RAFUNC_DISABLE_ALL)
+ input = FW_RA_IOT_N_COMB;
+ else
+ input = FW_RA_IOT_N_COMB | (((pHTInfo->IOTRaFunc)&0x0f) << 8);
+ input = input |((pHTInfo->IOTPeer & 0xf) <<12);
+ RT_TRACE(COMP_CMD, "[FW CMD] Set RA/IOT Comb in n mode!! input(%#x)\n", input);
+ write_nic_dword(dev, WFM5, input);
+ ChkFwCmdIoDone(dev);
+ break;
+
+ case FW_CMD_RA_REFRESH_BG_COMB:
+ RT_TRACE(COMP_CMD, "[FW CMD] Set RA B/G Combo refresh!!\n");
+ if(pHTInfo->IOTRaFunc & HT_IOT_RAFUNC_DISABLE_ALL)
+ input = FW_RA_IOT_BG_COMB;
+ else
+ input = FW_RA_IOT_BG_COMB | (((pHTInfo->IOTRaFunc)&0x0f) << 8);
+ input = input |((pHTInfo->IOTPeer & 0xf) <<12);
+ RT_TRACE(COMP_CMD, "[FW CMD] Set RA/IOT Comb in B/G mode!! input(%#x)\n", input);
+ write_nic_dword(dev, WFM5, input);
+ ChkFwCmdIoDone(dev);
break;
case FW_CMD_IQK_ENABLE:
write_nic_dword(dev, WFM5, FW_IQK_ENABLE);
+ ChkFwCmdIoDone(dev);
break;
case FW_CMD_TXPWR_TRACK_ENABLE:
write_nic_dword(dev, WFM5, FW_TXPWR_TRACK_ENABLE);
+ ChkFwCmdIoDone(dev);
break;
case FW_CMD_TXPWR_TRACK_DISABLE:
write_nic_dword(dev, WFM5, FW_TXPWR_TRACK_DISABLE);
+ ChkFwCmdIoDone(dev);
break;
- default:
- RT_TRACE(COMP_CMD,"Unknown FW Cmd IO(%#x)\n", priv->CurrentFwCmdIO);
+ case FW_CMD_PAUSE_DM_BY_SCAN:
+ RT_TRACE(COMP_CMD,"[FW CMD] Pause DM by Scan!!\n");
+ rtl8192_setBBreg(dev, rOFDM0_XAAGCCore1, bMaskByte0, 0x17);
+ rtl8192_setBBreg(dev, rOFDM0_XBAGCCore1, bMaskByte0, 0x17);
+ rtl8192_setBBreg(dev, rCCK0_CCA, bMaskByte2, 0x40);
break;
- }
- ChkFwCmdIoDone(dev);
-
- switch(priv->CurrentFwCmdIO)
- {
+ case FW_CMD_RESUME_DM_BY_SCAN:
+ RT_TRACE(COMP_CMD, "[FW CMD] Resume DM by Scan!!\n");
+ rtl8192_setBBreg(dev, rCCK0_CCA, bMaskByte2, 0x83);
+ PHY_SetTxPowerLevel8192S(dev, priv->chan);
+ break;
case FW_CMD_HIGH_PWR_DISABLE:
- //if(pMgntInfo->bTurboScan)
- {
- //Lower initial gain
- rtl8192_setBBreg(dev, rOFDM0_XAAGCCore1, bMaskByte0, 0x17);
- rtl8192_setBBreg(dev, rOFDM0_XBAGCCore1, bMaskByte0, 0x17);
- // CCA threshold
- rtl8192_setBBreg(dev, rCCK0_CCA, bMaskByte2, 0x40);
- // Disable OFDM Part
- rtl8192_setBBreg(dev, rOFDM0_TRMuxPar, bMaskByte2, 0x1);
- ScanRegister = rtl8192_QueryBBReg(dev, rOFDM0_RxDetector1,bMaskDWord);
- rtl8192_setBBreg(dev, rOFDM0_RxDetector1, 0xf, 0xf);
- rtl8192_setBBreg(dev, rOFDM1_TRxPathEnable, 0xf, 0x0);
- }
+ RT_TRACE(COMP_CMD, "[FW CMD] High Pwr Disable!!\n");
+ if(priv->DMFlag & HAL_DM_HIPWR_DISABLE)
+ break;
+ rtl8192_setBBreg(dev, rOFDM0_XAAGCCore1, bMaskByte0, 0x17);
+ rtl8192_setBBreg(dev, rOFDM0_XBAGCCore1, bMaskByte0, 0x17);
+ rtl8192_setBBreg(dev, rCCK0_CCA, bMaskByte2, 0x40);
break;
case FW_CMD_HIGH_PWR_ENABLE:
- //if(pMgntInfo->bTurboScan)
- {
- rtl8192_setBBreg(dev, rOFDM0_XAAGCCore1, bMaskByte0, 0x36);
- rtl8192_setBBreg(dev, rOFDM0_XBAGCCore1, bMaskByte0, 0x36);
+ RT_TRACE(COMP_CMD, "[FW CMD] High Pwr Enable!!\n");
+ if(priv->DMFlag & HAL_DM_HIPWR_DISABLE)
+ break;
+ rtl8192_setBBreg(dev, rCCK0_CCA, bMaskByte2, 0x83);
+ break;
- // CCA threshold
- rtl8192_setBBreg(dev, rCCK0_CCA, bMaskByte2, 0x83);
- // Enable OFDM Part
- rtl8192_setBBreg(dev, rOFDM0_TRMuxPar, bMaskByte2, 0x0);
+ case FW_CMD_LPS_ENTER:
+ RT_TRACE(COMP_CMD, "[FW CMD] Enter LPS mode!!\n");
+ CurrentAID = priv->ieee80211->assoc_id;
+ write_nic_dword(dev, WFM5, (FW_LPS_ENTER| ((CurrentAID|0xc000)<<8)) );
+ ChkFwCmdIoDone(dev);
+ pHTInfo->IOTAction |= HT_IOT_ACT_DISABLE_EDCA_TURBO;
+ break;
- //LZM ADD because sometimes there is no FW_CMD_HIGH_PWR_DISABLE, this value will be 0.
- if(ScanRegister != 0){
- rtl8192_setBBreg(dev, rOFDM0_RxDetector1, bMaskDWord, ScanRegister);
- }
+ case FW_CMD_LPS_LEAVE:
+ RT_TRACE(COMP_CMD, "[FW CMD] Leave LPS mode!!\n");
+ write_nic_dword(dev, WFM5, FW_LPS_LEAVE );
+ ChkFwCmdIoDone(dev);
+ pHTInfo->IOTAction &= (~HT_IOT_ACT_DISABLE_EDCA_TURBO);
+ break;
- if(priv->rf_type == RF_1T2R || priv->rf_type == RF_2T2R)
- rtl8192_setBBreg(dev, rOFDM1_TRxPathEnable, 0xf, 0x3);
- else
- rtl8192_setBBreg(dev, rOFDM1_TRxPathEnable, 0xf, 0x1);
- }
+ default:
break;
}
- priv->SetFwCmdInProgress = false;// Clear FW CMD operation flag.
+ priv->SetFwCmdInProgress = false;
RT_TRACE(COMP_CMD, "<---SetFwCmdIOWorkItemCallback()\n");
}
--
1.7.1
More information about the devel
mailing list