[PATCH 4/5] staging: remove aten2011 driver
Greg Kroah-Hartman
gregkh at suse.de
Tue Jul 28 21:46:17 UTC 2009
This driver is not needed, as the existing mos7840 driver works
properly for this device.
Thanks to Russell Lang for doing the work to figure this out.
Cc: Russell Lang <gsview at ghostgum.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh at suse.de>
---
drivers/staging/Kconfig | 2 -
drivers/staging/Makefile | 1 -
drivers/staging/uc2322/Kconfig | 10 -
drivers/staging/uc2322/Makefile | 1 -
drivers/staging/uc2322/TODO | 7 -
drivers/staging/uc2322/aten2011.c | 2430 -------------------------------------
6 files changed, 0 insertions(+), 2451 deletions(-)
delete mode 100644 drivers/staging/uc2322/Kconfig
delete mode 100644 drivers/staging/uc2322/Makefile
delete mode 100644 drivers/staging/uc2322/TODO
delete mode 100644 drivers/staging/uc2322/aten2011.c
diff --git a/drivers/staging/Kconfig b/drivers/staging/Kconfig
index 348bf61..975ecdd 100644
--- a/drivers/staging/Kconfig
+++ b/drivers/staging/Kconfig
@@ -103,8 +103,6 @@ source "drivers/staging/pohmelfs/Kconfig"
source "drivers/staging/stlc45xx/Kconfig"
-source "drivers/staging/uc2322/Kconfig"
-
source "drivers/staging/b3dfg/Kconfig"
source "drivers/staging/phison/Kconfig"
diff --git a/drivers/staging/Makefile b/drivers/staging/Makefile
index 8d61d7b..2241ae1 100644
--- a/drivers/staging/Makefile
+++ b/drivers/staging/Makefile
@@ -34,7 +34,6 @@ obj-$(CONFIG_ANDROID) += android/
obj-$(CONFIG_DST) += dst/
obj-$(CONFIG_POHMELFS) += pohmelfs/
obj-$(CONFIG_STLC45XX) += stlc45xx/
-obj-$(CONFIG_USB_SERIAL_ATEN2011) += uc2322/
obj-$(CONFIG_B3DFG) += b3dfg/
obj-$(CONFIG_IDE_PHISON) += phison/
obj-$(CONFIG_PLAN9AUTH) += p9auth/
diff --git a/drivers/staging/uc2322/Kconfig b/drivers/staging/uc2322/Kconfig
deleted file mode 100644
index 2e0c6e7..0000000
--- a/drivers/staging/uc2322/Kconfig
+++ /dev/null
@@ -1,10 +0,0 @@
-config USB_SERIAL_ATEN2011
- tristate "ATEN 2011 USB to serial device support"
- depends on USB_SERIAL
- default N
- ---help---
- Say Y here if you want to use a ATEN 2011 dual port USB to serial
- adapter.
-
- To compile this driver as a module, choose M here: the module will be
- called aten2011.
diff --git a/drivers/staging/uc2322/Makefile b/drivers/staging/uc2322/Makefile
deleted file mode 100644
index 49c18d6..0000000
--- a/drivers/staging/uc2322/Makefile
+++ /dev/null
@@ -1 +0,0 @@
-obj-$(CONFIG_USB_SERIAL_ATEN2011) += aten2011.o
diff --git a/drivers/staging/uc2322/TODO b/drivers/staging/uc2322/TODO
deleted file mode 100644
index c189a64..0000000
--- a/drivers/staging/uc2322/TODO
+++ /dev/null
@@ -1,7 +0,0 @@
-TODO:
- - checkpatch.pl cleanups
- - remove dead and useless code (auditing the tty ioctls to
- verify that they really are correct and needed.)
-
-Please send any patches to Greg Kroah-Hartman <greg at kroah.com> and
-Russell Lang <gsview at ghostgum.com.au>.
diff --git a/drivers/staging/uc2322/aten2011.c b/drivers/staging/uc2322/aten2011.c
deleted file mode 100644
index 39d0926..0000000
--- a/drivers/staging/uc2322/aten2011.c
+++ /dev/null
@@ -1,2430 +0,0 @@
-/*
- * Aten 2011 USB serial driver for 4 port devices
- *
- * Copyright (C) 2000 Inside Out Networks
- * Copyright (C) 2001-2002, 2009 Greg Kroah-Hartman <greg at kroah.com>
- * Copyright (C) 2009 Novell Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/init.h>
-#include <linux/slab.h>
-#include <linux/tty.h>
-#include <linux/tty_driver.h>
-#include <linux/tty_flip.h>
-#include <linux/module.h>
-#include <linux/serial.h>
-#include <linux/uaccess.h>
-#include <linux/usb.h>
-#include <linux/usb/serial.h>
-
-
-#define ZLP_REG1 0x3A /* Zero_Flag_Reg1 58 */
-#define ZLP_REG2 0x3B /* Zero_Flag_Reg2 59 */
-#define ZLP_REG3 0x3C /* Zero_Flag_Reg3 60 */
-#define ZLP_REG4 0x3D /* Zero_Flag_Reg4 61 */
-#define ZLP_REG5 0x3E /* Zero_Flag_Reg5 62 */
-
-/* Interrupt Rotinue Defines */
-#define SERIAL_IIR_RLS 0x06
-#define SERIAL_IIR_RDA 0x04
-#define SERIAL_IIR_CTI 0x0c
-#define SERIAL_IIR_THR 0x02
-#define SERIAL_IIR_MS 0x00
-
-/* Emulation of the bit mask on the LINE STATUS REGISTER. */
-#define SERIAL_LSR_DR 0x0001
-#define SERIAL_LSR_OE 0x0002
-#define SERIAL_LSR_PE 0x0004
-#define SERIAL_LSR_FE 0x0008
-#define SERIAL_LSR_BI 0x0010
-#define SERIAL_LSR_THRE 0x0020
-#define SERIAL_LSR_TEMT 0x0040
-#define SERIAL_LSR_FIFOERR 0x0080
-
-/* MSR bit defines(place holders) */
-#define ATEN_MSR_DELTA_CTS 0x10
-#define ATEN_MSR_DELTA_DSR 0x20
-#define ATEN_MSR_DELTA_RI 0x40
-#define ATEN_MSR_DELTA_CD 0x80
-
-/* Serial Port register Address */
-#define RECEIVE_BUFFER_REGISTER ((__u16)(0x00))
-#define TRANSMIT_HOLDING_REGISTER ((__u16)(0x00))
-#define INTERRUPT_ENABLE_REGISTER ((__u16)(0x01))
-#define INTERRUPT_IDENT_REGISTER ((__u16)(0x02))
-#define FIFO_CONTROL_REGISTER ((__u16)(0x02))
-#define LINE_CONTROL_REGISTER ((__u16)(0x03))
-#define MODEM_CONTROL_REGISTER ((__u16)(0x04))
-#define LINE_STATUS_REGISTER ((__u16)(0x05))
-#define MODEM_STATUS_REGISTER ((__u16)(0x06))
-#define SCRATCH_PAD_REGISTER ((__u16)(0x07))
-#define DIVISOR_LATCH_LSB ((__u16)(0x00))
-#define DIVISOR_LATCH_MSB ((__u16)(0x01))
-
-#define SP1_REGISTER ((__u16)(0x00))
-#define CONTROL1_REGISTER ((__u16)(0x01))
-#define CLK_MULTI_REGISTER ((__u16)(0x02))
-#define CLK_START_VALUE_REGISTER ((__u16)(0x03))
-#define DCR1_REGISTER ((__u16)(0x04))
-#define GPIO_REGISTER ((__u16)(0x07))
-
-#define SERIAL_LCR_DLAB ((__u16)(0x0080))
-
-/*
- * URB POOL related defines
- */
-#define NUM_URBS 16 /* URB Count */
-#define URB_TRANSFER_BUFFER_SIZE 32 /* URB Size */
-
-#define USB_VENDOR_ID_ATENINTL 0x0557
-#define ATENINTL_DEVICE_ID_2011 0x2011
-#define ATENINTL_DEVICE_ID_7820 0x7820
-
-static struct usb_device_id id_table[] = {
- { USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_2011) },
- { USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_7820) },
- { } /* terminating entry */
-};
-MODULE_DEVICE_TABLE(usb, id_table);
-
-/* This structure holds all of the local port information */
-struct ATENINTL_port {
- int port_num; /*Actual port number in the device(1,2,etc)*/
- __u8 bulk_out_endpoint; /* the bulk out endpoint handle */
- unsigned char *bulk_out_buffer; /* buffer used for the bulk out endpoint */
- struct urb *write_urb; /* write URB for this port */
- __u8 bulk_in_endpoint; /* the bulk in endpoint handle */
- unsigned char *bulk_in_buffer; /* the buffer we use for the bulk in endpoint */
- struct urb *read_urb; /* read URB for this port */
- __u8 shadowLCR; /* last LCR value received */
- __u8 shadowMCR; /* last MCR value received */
- char open;
- char chaseResponsePending;
- wait_queue_head_t wait_chase; /* for handling sleeping while waiting for chase to finish */
- wait_queue_head_t wait_command; /* for handling sleeping while waiting for command to finish */
- struct async_icount icount;
- struct usb_serial_port *port; /* loop back to the owner of this object */
- /*Offsets*/
- __u8 SpRegOffset;
- __u8 ControlRegOffset;
- __u8 DcrRegOffset;
- /* for processing control URBS in interrupt context */
- struct urb *control_urb;
- char *ctrl_buf;
- int MsrLsr;
-
- struct urb *write_urb_pool[NUM_URBS];
- /* we pass a pointer to this as the arguement sent to cypress_set_termios old_termios */
- struct ktermios tmp_termios; /* stores the old termios settings */
- spinlock_t lock; /* private lock */
-};
-
-/* This structure holds all of the individual serial device information */
-struct ATENINTL_serial {
- __u8 interrupt_in_endpoint; /* the interrupt endpoint handle */
- unsigned char *interrupt_in_buffer; /* the buffer we use for the interrupt endpoint */
- struct urb *interrupt_read_urb; /* our interrupt urb */
- __u8 bulk_in_endpoint; /* the bulk in endpoint handle */
- unsigned char *bulk_in_buffer; /* the buffer we use for the bulk in endpoint */
- struct urb *read_urb; /* our bulk read urb */
- __u8 bulk_out_endpoint; /* the bulk out endpoint handle */
- struct usb_serial *serial; /* loop back to the owner of this object */
- int ATEN2011_spectrum_2or4ports; /* this says the number of ports in the device */
- /* Indicates about the no.of opened ports of an individual USB-serial adapater. */
- unsigned int NoOfOpenPorts;
- /* a flag for Status endpoint polling */
- unsigned char status_polling_started;
-};
-
-static void ATEN2011_set_termios(struct tty_struct *tty,
- struct usb_serial_port *port,
- struct ktermios *old_termios);
-static void ATEN2011_change_port_settings(struct tty_struct *tty,
- struct ATENINTL_port *ATEN2011_port,
- struct ktermios *old_termios);
-
-/*************************************
- * Bit definitions for each register *
- *************************************/
-#define LCR_BITS_5 0x00 /* 5 bits/char */
-#define LCR_BITS_6 0x01 /* 6 bits/char */
-#define LCR_BITS_7 0x02 /* 7 bits/char */
-#define LCR_BITS_8 0x03 /* 8 bits/char */
-#define LCR_BITS_MASK 0x03 /* Mask for bits/char field */
-
-#define LCR_STOP_1 0x00 /* 1 stop bit */
-#define LCR_STOP_1_5 0x04 /* 1.5 stop bits (if 5 bits/char) */
-#define LCR_STOP_2 0x04 /* 2 stop bits (if 6-8 bits/char) */
-#define LCR_STOP_MASK 0x04 /* Mask for stop bits field */
-
-#define LCR_PAR_NONE 0x00 /* No parity */
-#define LCR_PAR_ODD 0x08 /* Odd parity */
-#define LCR_PAR_EVEN 0x18 /* Even parity */
-#define LCR_PAR_MARK 0x28 /* Force parity bit to 1 */
-#define LCR_PAR_SPACE 0x38 /* Force parity bit to 0 */
-#define LCR_PAR_MASK 0x38 /* Mask for parity field */
-
-#define LCR_SET_BREAK 0x40 /* Set Break condition */
-#define LCR_DL_ENABLE 0x80 /* Enable access to divisor latch */
-
-#define MCR_DTR 0x01 /* Assert DTR */
-#define MCR_RTS 0x02 /* Assert RTS */
-#define MCR_OUT1 0x04 /* Loopback only: Sets state of RI */
-#define MCR_MASTER_IE 0x08 /* Enable interrupt outputs */
-#define MCR_LOOPBACK 0x10 /* Set internal (digital) loopback mode */
-#define MCR_XON_ANY 0x20 /* Enable any char to exit XOFF mode */
-
-#define ATEN2011_MSR_CTS 0x10 /* Current state of CTS */
-#define ATEN2011_MSR_DSR 0x20 /* Current state of DSR */
-#define ATEN2011_MSR_RI 0x40 /* Current state of RI */
-#define ATEN2011_MSR_CD 0x80 /* Current state of CD */
-
-
-static int debug;
-
-/*
- * Version Information
- */
-#define DRIVER_VERSION "2.0"
-#define DRIVER_DESC "ATENINTL 2011 USB Serial Adapter"
-
-/*
- * Defines used for sending commands to port
- */
-
-#define ATEN_WDR_TIMEOUT (50) /* default urb timeout */
-
-/* Requests */
-#define ATEN_RD_RTYPE 0xC0
-#define ATEN_WR_RTYPE 0x40
-#define ATEN_RDREQ 0x0D
-#define ATEN_WRREQ 0x0E
-#define ATEN_CTRL_TIMEOUT 500
-#define VENDOR_READ_LENGTH (0x01)
-
-/* set to 1 for RS485 mode and 0 for RS232 mode */
-/* FIXME make this somehow dynamic and not build time specific */
-static int RS485mode;
-
-static int set_reg_sync(struct usb_serial_port *port, __u16 reg, __u16 val)
-{
- struct usb_device *dev = port->serial->dev;
- val = val & 0x00ff;
-
- dbg("%s: is %x, value %x", __func__, reg, val);
-
- return usb_control_msg(dev, usb_sndctrlpipe(dev, 0), ATEN_WRREQ,
- ATEN_WR_RTYPE, val, reg, NULL, 0,
- ATEN_WDR_TIMEOUT);
-}
-
-static int get_reg_sync(struct usb_serial_port *port, __u16 reg, __u16 *val)
-{
- struct usb_device *dev = port->serial->dev;
- int ret;
-
- ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), ATEN_RDREQ,
- ATEN_RD_RTYPE, 0, reg, val, VENDOR_READ_LENGTH,
- ATEN_WDR_TIMEOUT);
- dbg("%s: offset is %x, return val %x", __func__, reg, *val);
- *val = (*val) & 0x00ff;
- return ret;
-}
-
-static int set_uart_reg(struct usb_serial_port *port, __u16 reg, __u16 val)
-{
- struct usb_device *dev = port->serial->dev;
- struct ATENINTL_serial *a_serial;
- __u16 minor;
-
- a_serial = usb_get_serial_data(port->serial);
- minor = port->serial->minor;
- if (minor == SERIAL_TTY_NO_MINOR)
- minor = 0;
- val = val & 0x00ff;
-
- /*
- * For the UART control registers,
- * the application number need to be Or'ed
- */
- if (a_serial->ATEN2011_spectrum_2or4ports == 4)
- val |= (((__u16)port->number - minor) + 1) << 8;
- else {
- if (((__u16) port->number - minor) == 0)
- val |= (((__u16)port->number - minor) + 1) << 8;
- else
- val |= (((__u16)port->number - minor) + 2) << 8;
- }
- dbg("%s: application number is %x", __func__, val);
-
- return usb_control_msg(dev, usb_sndctrlpipe(dev, 0), ATEN_WRREQ,
- ATEN_WR_RTYPE, val, reg, NULL, 0,
- ATEN_WDR_TIMEOUT);
-}
-
-static int get_uart_reg(struct usb_serial_port *port, __u16 reg, __u16 *val)
-{
- struct usb_device *dev = port->serial->dev;
- int ret = 0;
- __u16 wval;
- struct ATENINTL_serial *a_serial;
- __u16 minor = port->serial->minor;
-
- a_serial = usb_get_serial_data(port->serial);
- if (minor == SERIAL_TTY_NO_MINOR)
- minor = 0;
-
- /* wval is same as application number */
- if (a_serial->ATEN2011_spectrum_2or4ports == 4)
- wval = (((__u16)port->number - minor) + 1) << 8;
- else {
- if (((__u16) port->number - minor) == 0)
- wval = (((__u16) port->number - minor) + 1) << 8;
- else
- wval = (((__u16) port->number - minor) + 2) << 8;
- }
- dbg("%s: application number is %x", __func__, wval);
- ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), ATEN_RDREQ,
- ATEN_RD_RTYPE, wval, reg, val, VENDOR_READ_LENGTH,
- ATEN_WDR_TIMEOUT);
- *val = (*val) & 0x00ff;
- return ret;
-}
-
-static int handle_newMsr(struct ATENINTL_port *port, __u8 newMsr)
-{
- struct ATENINTL_port *ATEN2011_port;
- struct async_icount *icount;
- ATEN2011_port = port;
- icount = &ATEN2011_port->icount;
- if (newMsr &
- (ATEN_MSR_DELTA_CTS | ATEN_MSR_DELTA_DSR | ATEN_MSR_DELTA_RI |
- ATEN_MSR_DELTA_CD)) {
- icount = &ATEN2011_port->icount;
-
- /* update input line counters */
- if (newMsr & ATEN_MSR_DELTA_CTS)
- icount->cts++;
- if (newMsr & ATEN_MSR_DELTA_DSR)
- icount->dsr++;
- if (newMsr & ATEN_MSR_DELTA_CD)
- icount->dcd++;
- if (newMsr & ATEN_MSR_DELTA_RI)
- icount->rng++;
- }
-
- return 0;
-}
-
-static int handle_newLsr(struct ATENINTL_port *port, __u8 newLsr)
-{
- struct async_icount *icount;
-
- dbg("%s - %02x", __func__, newLsr);
-
- if (newLsr & SERIAL_LSR_BI) {
- /*
- * Parity and Framing errors only count if they occur exclusive
- * of a break being received.
- */
- newLsr &= (__u8) (SERIAL_LSR_OE | SERIAL_LSR_BI);
- }
-
- /* update input line counters */
- icount = &port->icount;
- if (newLsr & SERIAL_LSR_BI)
- icount->brk++;
- if (newLsr & SERIAL_LSR_OE)
- icount->overrun++;
- if (newLsr & SERIAL_LSR_PE)
- icount->parity++;
- if (newLsr & SERIAL_LSR_FE)
- icount->frame++;
-
- return 0;
-}
-
-static void ATEN2011_control_callback(struct urb *urb)
-{
- unsigned char *data;
- struct ATENINTL_port *ATEN2011_port;
- __u8 regval = 0x0;
-
- switch (urb->status) {
- case 0:
- /* success */
- break;
- case -ECONNRESET:
- case -ENOENT:
- case -ESHUTDOWN:
- /* this urb is terminated, clean up */
- dbg("%s - urb shutting down with status: %d", __func__,
- urb->status);
- return;
- default:
- dbg("%s - nonzero urb status received: %d", __func__,
- urb->status);
- goto exit;
- }
-
- ATEN2011_port = (struct ATENINTL_port *)urb->context;
-
- dbg("%s urb buffer size is %d", __func__, urb->actual_length);
- dbg("%s ATEN2011_port->MsrLsr is %d port %d", __func__,
- ATEN2011_port->MsrLsr, ATEN2011_port->port_num);
- data = urb->transfer_buffer;
- regval = (__u8) data[0];
- dbg("%s data is %x", __func__, regval);
- if (ATEN2011_port->MsrLsr == 0)
- handle_newMsr(ATEN2011_port, regval);
- else if (ATEN2011_port->MsrLsr == 1)
- handle_newLsr(ATEN2011_port, regval);
-
-exit:
- return;
-}
-
-static int ATEN2011_get_reg(struct ATENINTL_port *ATEN, __u16 Wval, __u16 reg,
- __u16 *val)
-{
- struct usb_device *dev = ATEN->port->serial->dev;
- struct usb_ctrlrequest *dr = NULL;
- unsigned char *buffer = NULL;
- int ret = 0;
- buffer = (__u8 *) ATEN->ctrl_buf;
-
- dr = (void *)(buffer + 2);
- dr->bRequestType = ATEN_RD_RTYPE;
- dr->bRequest = ATEN_RDREQ;
- dr->wValue = cpu_to_le16(Wval);
- dr->wIndex = cpu_to_le16(reg);
- dr->wLength = cpu_to_le16(2);
-
- usb_fill_control_urb(ATEN->control_urb, dev, usb_rcvctrlpipe(dev, 0),
- (unsigned char *)dr, buffer, 2,
- ATEN2011_control_callback, ATEN);
- ATEN->control_urb->transfer_buffer_length = 2;
- ret = usb_submit_urb(ATEN->control_urb, GFP_ATOMIC);
- return ret;
-}
-
-static void ATEN2011_interrupt_callback(struct urb *urb)
-{
- int result;
- int length;
- struct ATENINTL_port *ATEN2011_port;
- struct ATENINTL_serial *ATEN2011_serial;
- struct usb_serial *serial;
- __u16 Data;
- unsigned char *data;
- __u8 sp[5], st;
- int i;
- __u16 wval;
- int minor;
-
- dbg("%s", " : Entering");
-
- ATEN2011_serial = (struct ATENINTL_serial *)urb->context;
-
- switch (urb->status) {
- case 0:
- /* success */
- break;
- case -ECONNRESET:
- case -ENOENT:
- case -ESHUTDOWN:
- /* this urb is terminated, clean up */
- dbg("%s - urb shutting down with status: %d", __func__,
- urb->status);
- return;
- default:
- dbg("%s - nonzero urb status received: %d", __func__,
- urb->status);
- goto exit;
- }
- length = urb->actual_length;
- data = urb->transfer_buffer;
-
- serial = ATEN2011_serial->serial;
-
- /* ATENINTL get 5 bytes
- * Byte 1 IIR Port 1 (port.number is 0)
- * Byte 2 IIR Port 2 (port.number is 1)
- * Byte 3 IIR Port 3 (port.number is 2)
- * Byte 4 IIR Port 4 (port.number is 3)
- * Byte 5 FIFO status for both */
-
- if (length && length > 5) {
- dbg("%s", "Wrong data !!!");
- return;
- }
-
- /* MATRIX */
- if (ATEN2011_serial->ATEN2011_spectrum_2or4ports == 4) {
- sp[0] = (__u8) data[0];
- sp[1] = (__u8) data[1];
- sp[2] = (__u8) data[2];
- sp[3] = (__u8) data[3];
- st = (__u8) data[4];
- } else {
- sp[0] = (__u8) data[0];
- sp[1] = (__u8) data[2];
- /* sp[2]=(__u8)data[2]; */
- /* sp[3]=(__u8)data[3]; */
- st = (__u8) data[4];
-
- }
- for (i = 0; i < serial->num_ports; i++) {
- ATEN2011_port = usb_get_serial_port_data(serial->port[i]);
- minor = serial->minor;
- if (minor == SERIAL_TTY_NO_MINOR)
- minor = 0;
- if ((ATEN2011_serial->ATEN2011_spectrum_2or4ports == 2)
- && (i != 0))
- wval =
- (((__u16) serial->port[i]->number -
- (__u16) (minor)) + 2) << 8;
- else
- wval =
- (((__u16) serial->port[i]->number -
- (__u16) (minor)) + 1) << 8;
- if (ATEN2011_port->open != 0) {
- if (sp[i] & 0x01) {
- dbg("SP%d No Interrupt !!!", i);
- } else {
- switch (sp[i] & 0x0f) {
- case SERIAL_IIR_RLS:
- dbg("Serial Port %d: Receiver status error or address bit detected in 9-bit mode", i);
- ATEN2011_port->MsrLsr = 1;
- ATEN2011_get_reg(ATEN2011_port, wval,
- LINE_STATUS_REGISTER,
- &Data);
- break;
- case SERIAL_IIR_MS:
- dbg("Serial Port %d: Modem status change", i);
- ATEN2011_port->MsrLsr = 0;
- ATEN2011_get_reg(ATEN2011_port, wval,
- MODEM_STATUS_REGISTER,
- &Data);
- break;
- }
- }
- }
-
- }
-exit:
- if (ATEN2011_serial->status_polling_started == 0)
- return;
-
- result = usb_submit_urb(urb, GFP_ATOMIC);
- if (result) {
- dev_err(&urb->dev->dev,
- "%s - Error %d submitting interrupt urb\n",
- __func__, result);
- }
-
- return;
-}
-
-static void ATEN2011_bulk_in_callback(struct urb *urb)
-{
- int status;
- unsigned char *data;
- struct usb_serial *serial;
- struct usb_serial_port *port;
- struct ATENINTL_serial *ATEN2011_serial;
- struct ATENINTL_port *ATEN2011_port;
- struct tty_struct *tty;
-
- if (urb->status) {
- dbg("nonzero read bulk status received: %d", urb->status);
- return;
- }
-
- ATEN2011_port = (struct ATENINTL_port *)urb->context;
-
- port = (struct usb_serial_port *)ATEN2011_port->port;
- serial = port->serial;
-
- dbg("%s", "Entering...");
-
- data = urb->transfer_buffer;
- ATEN2011_serial = usb_get_serial_data(serial);
-
- if (urb->actual_length) {
- tty = tty_port_tty_get(&ATEN2011_port->port->port);
- if (tty) {
- tty_buffer_request_room(tty, urb->actual_length);
- tty_insert_flip_string(tty, data, urb->actual_length);
- tty_flip_buffer_push(tty);
- tty_kref_put(tty);
- }
-
- ATEN2011_port->icount.rx += urb->actual_length;
- dbg("ATEN2011_port->icount.rx is %d:",
- ATEN2011_port->icount.rx);
- }
-
- if (!ATEN2011_port->read_urb) {
- dbg("%s", "URB KILLED !!!");
- return;
- }
-
- if (ATEN2011_port->read_urb->status != -EINPROGRESS) {
- ATEN2011_port->read_urb->dev = serial->dev;
-
- status = usb_submit_urb(ATEN2011_port->read_urb, GFP_ATOMIC);
- if (status)
- dbg("usb_submit_urb(read bulk) failed, status = %d", status);
- }
-}
-
-static void ATEN2011_bulk_out_data_callback(struct urb *urb)
-{
- struct ATENINTL_port *ATEN2011_port;
- struct tty_struct *tty;
-
- if (urb->status) {
- dbg("nonzero write bulk status received:%d", urb->status);
- return;
- }
-
- ATEN2011_port = (struct ATENINTL_port *)urb->context;
-
- dbg("%s", "Entering .........");
-
- tty = tty_port_tty_get(&ATEN2011_port->port->port);
-
- if (tty && ATEN2011_port->open)
- /* tell the tty driver that something has changed */
- tty_wakeup(tty);
-
- /* schedule_work(&ATEN2011_port->port->work); */
- tty_kref_put(tty);
-
-}
-
-#ifdef ATENSerialProbe
-static int ATEN2011_serial_probe(struct usb_serial *serial,
- const struct usb_device_id *id)
-{
-
- /*need to implement the mode_reg reading and updating\
- structures usb_serial_ device_type\
- (i.e num_ports, num_bulkin,bulkout etc) */
- /* Also we can update the changes attach */
- return 1;
-}
-#endif
-
-static int ATEN2011_open(struct tty_struct *tty, struct usb_serial_port *port,
- struct file *filp)
-{
- int response;
- int j;
- struct usb_serial *serial;
- struct urb *urb;
- __u16 Data;
- int status;
- struct ATENINTL_serial *ATEN2011_serial;
- struct ATENINTL_port *ATEN2011_port;
- struct ktermios tmp_termios;
- int minor;
-
- serial = port->serial;
-
- ATEN2011_port = usb_get_serial_port_data(port);
-
- if (ATEN2011_port == NULL)
- return -ENODEV;
-
- ATEN2011_serial = usb_get_serial_data(serial);
- if (ATEN2011_serial == NULL)
- return -ENODEV;
-
- /* increment the number of opened ports counter here */
- ATEN2011_serial->NoOfOpenPorts++;
-
- usb_clear_halt(serial->dev, port->write_urb->pipe);
- usb_clear_halt(serial->dev, port->read_urb->pipe);
-
- /* Initialising the write urb pool */
- for (j = 0; j < NUM_URBS; ++j) {
- urb = usb_alloc_urb(0, GFP_ATOMIC);
- ATEN2011_port->write_urb_pool[j] = urb;
-
- if (urb == NULL) {
- err("No more urbs???");
- continue;
- }
-
- urb->transfer_buffer = NULL;
- urb->transfer_buffer =
- kmalloc(URB_TRANSFER_BUFFER_SIZE, GFP_KERNEL);
- if (!urb->transfer_buffer) {
- err("%s-out of memory for urb buffers.", __func__);
- continue;
- }
- }
-
-/*****************************************************************************
- * Initialize ATEN2011 -- Write Init values to corresponding Registers
- *
- * Register Index
- * 1 : IER
- * 2 : FCR
- * 3 : LCR
- * 4 : MCR
- *
- * 0x08 : SP1/2 Control Reg
- *****************************************************************************/
-
-/* NEED to check the fallowing Block */
-
- Data = 0x0;
- status = get_reg_sync(port, ATEN2011_port->SpRegOffset, &Data);
- if (status < 0) {
- dbg("Reading Spreg failed");
- return -1;
- }
- Data |= 0x80;
- status = set_reg_sync(port, ATEN2011_port->SpRegOffset, Data);
- if (status < 0) {
- dbg("writing Spreg failed");
- return -1;
- }
-
- Data &= ~0x80;
- status = set_reg_sync(port, ATEN2011_port->SpRegOffset, Data);
- if (status < 0) {
- dbg("writing Spreg failed");
- return -1;
- }
-
-/* End of block to be checked */
-/**************************CHECK***************************/
-
- if (RS485mode == 0)
- Data = 0xC0;
- else
- Data = 0x00;
- status = set_uart_reg(port, SCRATCH_PAD_REGISTER, Data);
- if (status < 0) {
- dbg("Writing SCRATCH_PAD_REGISTER failed status-0x%x", status);
- return -1;
- } else
- dbg("SCRATCH_PAD_REGISTER Writing success status%d", status);
-
-/**************************CHECK***************************/
-
- Data = 0x0;
- status = get_reg_sync(port, ATEN2011_port->ControlRegOffset, &Data);
- if (status < 0) {
- dbg("Reading Controlreg failed");
- return -1;
- }
- Data |= 0x08; /* Driver done bit */
- Data |= 0x20; /* rx_disable */
- status = 0;
- status =
- set_reg_sync(port, ATEN2011_port->ControlRegOffset, Data);
- if (status < 0) {
- dbg("writing Controlreg failed");
- return -1;
- }
- /*
- * do register settings here
- * Set all regs to the device default values.
- * First Disable all interrupts.
- */
-
- Data = 0x00;
- status = set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
- if (status < 0) {
- dbg("disableing interrupts failed");
- return -1;
- }
- /* Set FIFO_CONTROL_REGISTER to the default value */
- Data = 0x00;
- status = set_uart_reg(port, FIFO_CONTROL_REGISTER, Data);
- if (status < 0) {
- dbg("Writing FIFO_CONTROL_REGISTER failed");
- return -1;
- }
-
- Data = 0xcf; /* chk */
- status = set_uart_reg(port, FIFO_CONTROL_REGISTER, Data);
- if (status < 0) {
- dbg("Writing FIFO_CONTROL_REGISTER failed");
- return -1;
- }
-
- Data = 0x03; /* LCR_BITS_8 */
- status = set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
- ATEN2011_port->shadowLCR = Data;
-
- Data = 0x0b; /* MCR_DTR|MCR_RTS|MCR_MASTER_IE */
- status = set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
- ATEN2011_port->shadowMCR = Data;
-
-#ifdef Check
- Data = 0x00;
- status = get_uart_reg(port, LINE_CONTROL_REGISTER, &Data);
- ATEN2011_port->shadowLCR = Data;
-
- Data |= SERIAL_LCR_DLAB; /* data latch enable in LCR 0x80 */
- status = set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
-
- Data = 0x0c;
- status = set_uart_reg(port, DIVISOR_LATCH_LSB, Data);
-
- Data = 0x0;
- status = set_uart_reg(port, DIVISOR_LATCH_MSB, Data);
-
- Data = 0x00;
- status = get_uart_reg(port, LINE_CONTROL_REGISTER, &Data);
-
-/* Data = ATEN2011_port->shadowLCR; */ /* data latch disable */
- Data = Data & ~SERIAL_LCR_DLAB;
- status = set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
- ATEN2011_port->shadowLCR = Data;
-#endif
- /* clearing Bulkin and Bulkout Fifo */
- Data = 0x0;
- status = get_reg_sync(port, ATEN2011_port->SpRegOffset, &Data);
-
- Data = Data | 0x0c;
- status = set_reg_sync(port, ATEN2011_port->SpRegOffset, Data);
-
- Data = Data & ~0x0c;
- status = set_reg_sync(port, ATEN2011_port->SpRegOffset, Data);
- /* Finally enable all interrupts */
- Data = 0x0;
- Data = 0x0c;
- status = set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
-
- /* clearing rx_disable */
- Data = 0x0;
- status = get_reg_sync(port, ATEN2011_port->ControlRegOffset, &Data);
- Data = Data & ~0x20;
- status = set_reg_sync(port, ATEN2011_port->ControlRegOffset, Data);
-
- /* rx_negate */
- Data = 0x0;
- status = get_reg_sync(port, ATEN2011_port->ControlRegOffset, &Data);
- Data = Data | 0x10;
- status = 0;
- status = set_reg_sync(port, ATEN2011_port->ControlRegOffset, Data);
-
- /*
- * Check to see if we've set up our endpoint info yet
- * (can't set it up in ATEN2011_startup as the structures
- * were not set up at that time.)
- */
- if (ATEN2011_serial->NoOfOpenPorts == 1) {
- /* start the status polling here */
- ATEN2011_serial->status_polling_started = 1;
- /* If not yet set, Set here */
- ATEN2011_serial->interrupt_in_buffer =
- serial->port[0]->interrupt_in_buffer;
- ATEN2011_serial->interrupt_in_endpoint =
- serial->port[0]->interrupt_in_endpointAddress;
- ATEN2011_serial->interrupt_read_urb =
- serial->port[0]->interrupt_in_urb;
-
- /* set up interrupt urb */
- usb_fill_int_urb(ATEN2011_serial->interrupt_read_urb,
- serial->dev,
- usb_rcvintpipe(serial->dev,
- ATEN2011_serial->
- interrupt_in_endpoint),
- ATEN2011_serial->interrupt_in_buffer,
- ATEN2011_serial->interrupt_read_urb->
- transfer_buffer_length,
- ATEN2011_interrupt_callback, ATEN2011_serial,
- ATEN2011_serial->interrupt_read_urb->interval);
-
- /* start interrupt read for ATEN2011 *
- * will continue as long as ATEN2011 is connected */
-
- response =
- usb_submit_urb(ATEN2011_serial->interrupt_read_urb,
- GFP_KERNEL);
- if (response) {
- dbg("%s - Error %d submitting interrupt urb",
- __func__, response);
- }
-
- }
-
- /*
- * See if we've set up our endpoint info yet
- * (can't set it up in ATEN2011_startup as the
- * structures were not set up at that time.)
- */
-
- dbg("port number is %d", port->number);
- dbg("serial number is %d", port->serial->minor);
- dbg("Bulkin endpoint is %d", port->bulk_in_endpointAddress);
- dbg("BulkOut endpoint is %d", port->bulk_out_endpointAddress);
- dbg("Interrupt endpoint is %d",
- port->interrupt_in_endpointAddress);
- dbg("port's number in the device is %d", ATEN2011_port->port_num);
- ATEN2011_port->bulk_in_buffer = port->bulk_in_buffer;
- ATEN2011_port->bulk_in_endpoint = port->bulk_in_endpointAddress;
- ATEN2011_port->read_urb = port->read_urb;
- ATEN2011_port->bulk_out_endpoint = port->bulk_out_endpointAddress;
-
- minor = port->serial->minor;
- if (minor == SERIAL_TTY_NO_MINOR)
- minor = 0;
-
- /* set up our bulk in urb */
- if ((ATEN2011_serial->ATEN2011_spectrum_2or4ports == 2)
- && (((__u16) port->number - (__u16) (minor)) != 0)) {
- usb_fill_bulk_urb(ATEN2011_port->read_urb, serial->dev,
- usb_rcvbulkpipe(serial->dev,
- (port->
- bulk_in_endpointAddress +
- 2)), port->bulk_in_buffer,
- ATEN2011_port->read_urb->
- transfer_buffer_length,
- ATEN2011_bulk_in_callback, ATEN2011_port);
- } else
- usb_fill_bulk_urb(ATEN2011_port->read_urb,
- serial->dev,
- usb_rcvbulkpipe(serial->dev,
- port->
- bulk_in_endpointAddress),
- port->bulk_in_buffer,
- ATEN2011_port->read_urb->
- transfer_buffer_length,
- ATEN2011_bulk_in_callback, ATEN2011_port);
-
- dbg("ATEN2011_open: bulkin endpoint is %d",
- port->bulk_in_endpointAddress);
- response = usb_submit_urb(ATEN2011_port->read_urb, GFP_KERNEL);
- if (response) {
- err("%s - Error %d submitting control urb", __func__,
- response);
- }
-
- /* initialize our wait queues */
- init_waitqueue_head(&ATEN2011_port->wait_chase);
- init_waitqueue_head(&ATEN2011_port->wait_command);
-
- /* initialize our icount structure */
- memset(&(ATEN2011_port->icount), 0x00, sizeof(ATEN2011_port->icount));
-
- /* initialize our port settings */
- ATEN2011_port->shadowMCR = MCR_MASTER_IE; /* Must set to enable ints! */
- ATEN2011_port->chaseResponsePending = 0;
- /* send a open port command */
- ATEN2011_port->open = 1;
- /* ATEN2011_change_port_settings(ATEN2011_port,old_termios); */
- /* Setup termios */
- ATEN2011_set_termios(tty, port, &tmp_termios);
- ATEN2011_port->icount.tx = 0;
- ATEN2011_port->icount.rx = 0;
-
- dbg("usb_serial serial:%x ATEN2011_port:%x\nATEN2011_serial:%x usb_serial_port port:%x",
- (unsigned int)serial, (unsigned int)ATEN2011_port,
- (unsigned int)ATEN2011_serial, (unsigned int)port);
-
- return 0;
-
-}
-
-static int ATEN2011_chars_in_buffer(struct tty_struct *tty)
-{
- struct usb_serial_port *port = tty->driver_data;
- int i;
- int chars = 0;
- struct ATENINTL_port *ATEN2011_port;
-
- /* dbg("%s"," ATEN2011_chars_in_buffer:entering ..........."); */
-
- ATEN2011_port = usb_get_serial_port_data(port);
- if (ATEN2011_port == NULL) {
- dbg("%s", "ATEN2011_break:leaving ...........");
- return -1;
- }
-
- for (i = 0; i < NUM_URBS; ++i)
- if (ATEN2011_port->write_urb_pool[i]->status == -EINPROGRESS)
- chars += URB_TRANSFER_BUFFER_SIZE;
-
- dbg("%s - returns %d", __func__, chars);
- return chars;
-
-}
-
-static void ATEN2011_block_until_tx_empty(struct tty_struct *tty,
- struct ATENINTL_port *ATEN2011_port)
-{
- int timeout = HZ / 10;
- int wait = 30;
- int count;
-
- while (1) {
- count = ATEN2011_chars_in_buffer(tty);
-
- /* Check for Buffer status */
- if (count <= 0)
- return;
-
- /* Block the thread for a while */
- interruptible_sleep_on_timeout(&ATEN2011_port->wait_chase,
- timeout);
-
- /* No activity.. count down section */
- wait--;
- if (wait == 0) {
- dbg("%s - TIMEOUT", __func__);
- return;
- } else {
- /* Reset timout value back to seconds */
- wait = 30;
- }
- }
-}
-
-static void ATEN2011_close(struct tty_struct *tty, struct usb_serial_port *port,
- struct file *filp)
-{
- struct usb_serial *serial;
- struct ATENINTL_serial *ATEN2011_serial;
- struct ATENINTL_port *ATEN2011_port;
- int no_urbs;
- __u16 Data;
-
- dbg("%s", "ATEN2011_close:entering...");
- serial = port->serial;
-
- /* take the Adpater and port's private data */
- ATEN2011_serial = usb_get_serial_data(serial);
- ATEN2011_port = usb_get_serial_port_data(port);
- if ((ATEN2011_serial == NULL) || (ATEN2011_port == NULL))
- return;
-
- if (serial->dev) {
- /* flush and block(wait) until tx is empty */
- ATEN2011_block_until_tx_empty(tty, ATEN2011_port);
- }
- /* kill the ports URB's */
- for (no_urbs = 0; no_urbs < NUM_URBS; no_urbs++)
- usb_kill_urb(ATEN2011_port->write_urb_pool[no_urbs]);
- /* Freeing Write URBs */
- for (no_urbs = 0; no_urbs < NUM_URBS; ++no_urbs) {
- kfree(ATEN2011_port->write_urb_pool[no_urbs]->transfer_buffer);
- usb_free_urb(ATEN2011_port->write_urb_pool[no_urbs]);
- }
- /* While closing port, shutdown all bulk read, write *
- * and interrupt read if they exists */
- if (serial->dev) {
- if (ATEN2011_port->write_urb) {
- dbg("%s", "Shutdown bulk write");
- usb_kill_urb(ATEN2011_port->write_urb);
- }
- if (ATEN2011_port->read_urb) {
- dbg("%s", "Shutdown bulk read");
- usb_kill_urb(ATEN2011_port->read_urb);
- }
- if ((&ATEN2011_port->control_urb)) {
- dbg("%s", "Shutdown control read");
- /* usb_kill_urb (ATEN2011_port->control_urb); */
-
- }
- }
- /* if(ATEN2011_port->ctrl_buf != NULL) */
- /* kfree(ATEN2011_port->ctrl_buf); */
- /* decrement the no.of open ports counter of an individual USB-serial adapter. */
- ATEN2011_serial->NoOfOpenPorts--;
- dbg("NoOfOpenPorts in close%d:in port%d",
- ATEN2011_serial->NoOfOpenPorts, port->number);
- if (ATEN2011_serial->NoOfOpenPorts == 0) {
- /* stop the stus polling here */
- ATEN2011_serial->status_polling_started = 0;
- if (ATEN2011_serial->interrupt_read_urb) {
- dbg("%s", "Shutdown interrupt_read_urb");
- /* ATEN2011_serial->interrupt_in_buffer=NULL; */
- /* usb_kill_urb (ATEN2011_serial->interrupt_read_urb); */
- }
- }
- if (ATEN2011_port->write_urb) {
- /* if this urb had a transfer buffer already (old tx) free it */
- kfree(ATEN2011_port->write_urb->transfer_buffer);
- usb_free_urb(ATEN2011_port->write_urb);
- }
-
- /* clear the MCR & IER */
- Data = 0x00;
- set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
- Data = 0x00;
- set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
-
- ATEN2011_port->open = 0;
- dbg("%s", "Leaving ............");
-
-}
-
-static void ATEN2011_block_until_chase_response(struct tty_struct *tty,
- struct ATENINTL_port
- *ATEN2011_port)
-{
- int timeout = 1 * HZ;
- int wait = 10;
- int count;
-
- while (1) {
- count = ATEN2011_chars_in_buffer(tty);
-
- /* Check for Buffer status */
- if (count <= 0) {
- ATEN2011_port->chaseResponsePending = 0;
- return;
- }
-
- /* Block the thread for a while */
- interruptible_sleep_on_timeout(&ATEN2011_port->wait_chase,
- timeout);
- /* No activity.. count down section */
- wait--;
- if (wait == 0) {
- dbg("%s - TIMEOUT", __func__);
- return;
- } else {
- /* Reset timout value back to seconds */
- wait = 10;
- }
- }
-
-}
-
-static void ATEN2011_break(struct tty_struct *tty, int break_state)
-{
- struct usb_serial_port *port = tty->driver_data;
- unsigned char data;
- struct usb_serial *serial;
- struct ATENINTL_serial *ATEN2011_serial;
- struct ATENINTL_port *ATEN2011_port;
-
- dbg("%s", "Entering ...........");
- dbg("ATEN2011_break: Start");
-
- serial = port->serial;
-
- ATEN2011_serial = usb_get_serial_data(serial);
- ATEN2011_port = usb_get_serial_port_data(port);
-
- if ((ATEN2011_serial == NULL) || (ATEN2011_port == NULL))
- return;
-
- /* flush and chase */
- ATEN2011_port->chaseResponsePending = 1;
-
- if (serial->dev) {
- /* flush and block until tx is empty */
- ATEN2011_block_until_chase_response(tty, ATEN2011_port);
- }
-
- if (break_state == -1)
- data = ATEN2011_port->shadowLCR | LCR_SET_BREAK;
- else
- data = ATEN2011_port->shadowLCR & ~LCR_SET_BREAK;
-
- ATEN2011_port->shadowLCR = data;
- dbg("ATEN2011_break ATEN2011_port->shadowLCR is %x",
- ATEN2011_port->shadowLCR);
- set_uart_reg(port, LINE_CONTROL_REGISTER, ATEN2011_port->shadowLCR);
-
- return;
-}
-
-static int ATEN2011_write_room(struct tty_struct *tty)
-{
- struct usb_serial_port *port = tty->driver_data;
- int i;
- int room = 0;
- struct ATENINTL_port *ATEN2011_port;
-
- ATEN2011_port = usb_get_serial_port_data(port);
- if (ATEN2011_port == NULL) {
- dbg("%s", "ATEN2011_break:leaving ...........");
- return -1;
- }
-
- for (i = 0; i < NUM_URBS; ++i)
- if (ATEN2011_port->write_urb_pool[i]->status != -EINPROGRESS)
- room += URB_TRANSFER_BUFFER_SIZE;
-
- dbg("%s - returns %d", __func__, room);
- return room;
-
-}
-
-static int ATEN2011_write(struct tty_struct *tty, struct usb_serial_port *port,
- const unsigned char *data, int count)
-{
- int status;
- int i;
- int bytes_sent = 0;
- int transfer_size;
- int minor;
-
- struct ATENINTL_port *ATEN2011_port;
- struct usb_serial *serial;
- struct ATENINTL_serial *ATEN2011_serial;
- struct urb *urb;
- const unsigned char *current_position = data;
- unsigned char *data1;
- dbg("%s", "entering ...........");
-
- serial = port->serial;
-
- ATEN2011_port = usb_get_serial_port_data(port);
- if (ATEN2011_port == NULL) {
- dbg("%s", "ATEN2011_port is NULL");
- return -1;
- }
-
- ATEN2011_serial = usb_get_serial_data(serial);
- if (ATEN2011_serial == NULL) {
- dbg("%s", "ATEN2011_serial is NULL");
- return -1;
- }
-
- /* try to find a free urb in the list */
- urb = NULL;
-
- for (i = 0; i < NUM_URBS; ++i) {
- if (ATEN2011_port->write_urb_pool[i]->status != -EINPROGRESS) {
- urb = ATEN2011_port->write_urb_pool[i];
- dbg("URB:%d", i);
- break;
- }
- }
-
- if (urb == NULL) {
- dbg("%s - no more free urbs", __func__);
- goto exit;
- }
-
- if (urb->transfer_buffer == NULL) {
- urb->transfer_buffer =
- kmalloc(URB_TRANSFER_BUFFER_SIZE, GFP_KERNEL);
-
- if (urb->transfer_buffer == NULL) {
- err("%s no more kernel memory...", __func__);
- goto exit;
- }
- }
- transfer_size = min(count, URB_TRANSFER_BUFFER_SIZE);
-
- memcpy(urb->transfer_buffer, current_position, transfer_size);
- /* usb_serial_debug_data (__FILE__, __func__, transfer_size, urb->transfer_buffer); */
-
- /* fill urb with data and submit */
- minor = port->serial->minor;
- if (minor == SERIAL_TTY_NO_MINOR)
- minor = 0;
- if ((ATEN2011_serial->ATEN2011_spectrum_2or4ports == 2)
- && (((__u16) port->number - (__u16) (minor)) != 0)) {
- usb_fill_bulk_urb(urb, ATEN2011_serial->serial->dev,
- usb_sndbulkpipe(ATEN2011_serial->serial->dev,
- (port->
- bulk_out_endpointAddress) +
- 2), urb->transfer_buffer,
- transfer_size,
- ATEN2011_bulk_out_data_callback,
- ATEN2011_port);
- } else
-
- usb_fill_bulk_urb(urb,
- ATEN2011_serial->serial->dev,
- usb_sndbulkpipe(ATEN2011_serial->serial->dev,
- port->
- bulk_out_endpointAddress),
- urb->transfer_buffer, transfer_size,
- ATEN2011_bulk_out_data_callback,
- ATEN2011_port);
-
- data1 = urb->transfer_buffer;
- dbg("bulkout endpoint is %d", port->bulk_out_endpointAddress);
- /* for(i=0;i < urb->actual_length;i++) */
- /* dbg("Data is %c ",data1[i]); */
-
- /* send it down the pipe */
- status = usb_submit_urb(urb, GFP_ATOMIC);
-
- if (status) {
- err("%s - usb_submit_urb(write bulk) failed with status = %d",
- __func__, status);
- bytes_sent = status;
- goto exit;
- }
- bytes_sent = transfer_size;
- ATEN2011_port->icount.tx += transfer_size;
- dbg("ATEN2011_port->icount.tx is %d:", ATEN2011_port->icount.tx);
-
-exit:
- return bytes_sent;
-}
-
-static void ATEN2011_throttle(struct tty_struct *tty)
-{
- struct usb_serial_port *port = tty->driver_data;
- struct ATENINTL_port *ATEN2011_port;
- int status;
-
- dbg("- port %d", port->number);
-
- ATEN2011_port = usb_get_serial_port_data(port);
-
- if (ATEN2011_port == NULL)
- return;
-
- if (!ATEN2011_port->open) {
- dbg("%s", "port not opened");
- return;
- }
-
- dbg("%s", "Entering .......... ");
-
- if (!tty) {
- dbg("%s - no tty available", __func__);
- return;
- }
-
- /* if we are implementing XON/XOFF, send the stop character */
- if (I_IXOFF(tty)) {
- unsigned char stop_char = STOP_CHAR(tty);
- status = ATEN2011_write(tty, port, &stop_char, 1);
- if (status <= 0)
- return;
- }
-
- /* if we are implementing RTS/CTS, toggle that line */
- if (tty->termios->c_cflag & CRTSCTS) {
- ATEN2011_port->shadowMCR &= ~MCR_RTS;
- status = set_uart_reg(port, MODEM_CONTROL_REGISTER,
- ATEN2011_port->shadowMCR);
- if (status < 0)
- return;
- }
-
- return;
-}
-
-static void ATEN2011_unthrottle(struct tty_struct *tty)
-{
- struct usb_serial_port *port = tty->driver_data;
- int status;
- struct ATENINTL_port *ATEN2011_port = usb_get_serial_port_data(port);
-
- if (ATEN2011_port == NULL)
- return;
-
- if (!ATEN2011_port->open) {
- dbg("%s - port not opened", __func__);
- return;
- }
-
- dbg("%s", "Entering .......... ");
-
- if (!tty) {
- dbg("%s - no tty available", __func__);
- return;
- }
-
- /* if we are implementing XON/XOFF, send the start character */
- if (I_IXOFF(tty)) {
- unsigned char start_char = START_CHAR(tty);
- status = ATEN2011_write(tty, port, &start_char, 1);
- if (status <= 0)
- return;
- }
-
- /* if we are implementing RTS/CTS, toggle that line */
- if (tty->termios->c_cflag & CRTSCTS) {
- ATEN2011_port->shadowMCR |= MCR_RTS;
- status = set_uart_reg(port, MODEM_CONTROL_REGISTER,
- ATEN2011_port->shadowMCR);
- if (status < 0)
- return;
- }
-
- return;
-}
-
-static int ATEN2011_tiocmget(struct tty_struct *tty, struct file *file)
-{
- struct usb_serial_port *port = tty->driver_data;
- struct ATENINTL_port *ATEN2011_port;
- unsigned int result;
- __u16 msr;
- __u16 mcr;
- /* unsigned int mcr; */
- int status = 0;
- ATEN2011_port = usb_get_serial_port_data(port);
-
- dbg("%s - port %d", __func__, port->number);
-
- if (ATEN2011_port == NULL)
- return -ENODEV;
-
- status = get_uart_reg(port, MODEM_STATUS_REGISTER, &msr);
- status = get_uart_reg(port, MODEM_CONTROL_REGISTER, &mcr);
- /* mcr = ATEN2011_port->shadowMCR; */
- /* COMMENT2: the Fallowing three line are commented for updating only MSR values */
- result = ((mcr & MCR_DTR) ? TIOCM_DTR : 0)
- | ((mcr & MCR_RTS) ? TIOCM_RTS : 0)
- | ((mcr & MCR_LOOPBACK) ? TIOCM_LOOP : 0)
- | ((msr & ATEN2011_MSR_CTS) ? TIOCM_CTS : 0)
- | ((msr & ATEN2011_MSR_CD) ? TIOCM_CAR : 0)
- | ((msr & ATEN2011_MSR_RI) ? TIOCM_RI : 0)
- | ((msr & ATEN2011_MSR_DSR) ? TIOCM_DSR : 0);
-
- dbg("%s - 0x%04X", __func__, result);
-
- return result;
-}
-
-static int ATEN2011_tiocmset(struct tty_struct *tty, struct file *file,
- unsigned int set, unsigned int clear)
-{
- struct usb_serial_port *port = tty->driver_data;
- struct ATENINTL_port *ATEN2011_port;
- unsigned int mcr;
- unsigned int status;
-
- dbg("%s - port %d", __func__, port->number);
-
- ATEN2011_port = usb_get_serial_port_data(port);
-
- if (ATEN2011_port == NULL)
- return -ENODEV;
-
- mcr = ATEN2011_port->shadowMCR;
- if (clear & TIOCM_RTS)
- mcr &= ~MCR_RTS;
- if (clear & TIOCM_DTR)
- mcr &= ~MCR_DTR;
- if (clear & TIOCM_LOOP)
- mcr &= ~MCR_LOOPBACK;
-
- if (set & TIOCM_RTS)
- mcr |= MCR_RTS;
- if (set & TIOCM_DTR)
- mcr |= MCR_DTR;
- if (set & TIOCM_LOOP)
- mcr |= MCR_LOOPBACK;
-
- ATEN2011_port->shadowMCR = mcr;
-
- status = set_uart_reg(port, MODEM_CONTROL_REGISTER, mcr);
- if (status < 0) {
- dbg("setting MODEM_CONTROL_REGISTER Failed");
- return -1;
- }
-
- return 0;
-}
-
-static void ATEN2011_set_termios(struct tty_struct *tty,
- struct usb_serial_port *port,
- struct ktermios *old_termios)
-{
- int status;
- unsigned int cflag;
- struct usb_serial *serial;
- struct ATENINTL_port *ATEN2011_port;
-
- dbg("ATEN2011_set_termios: START");
-
- serial = port->serial;
-
- ATEN2011_port = usb_get_serial_port_data(port);
-
- if (ATEN2011_port == NULL)
- return;
-
- if (!ATEN2011_port->open) {
- dbg("%s - port not opened", __func__);
- return;
- }
-
- dbg("%s", "setting termios - ");
-
- cflag = tty->termios->c_cflag;
-
- dbg("%s - cflag %08x iflag %08x", __func__,
- tty->termios->c_cflag, RELEVANT_IFLAG(tty->termios->c_iflag));
-
- if (old_termios) {
- dbg("%s - old clfag %08x old iflag %08x", __func__,
- old_termios->c_cflag, RELEVANT_IFLAG(old_termios->c_iflag));
- }
-
- dbg("%s - port %d", __func__, port->number);
-
- /* change the port settings to the new ones specified */
-
- ATEN2011_change_port_settings(tty, ATEN2011_port, old_termios);
-
- if (!ATEN2011_port->read_urb) {
- dbg("%s", "URB KILLED !!!!!");
- return;
- }
-
- if (ATEN2011_port->read_urb->status != -EINPROGRESS) {
- ATEN2011_port->read_urb->dev = serial->dev;
- status = usb_submit_urb(ATEN2011_port->read_urb, GFP_ATOMIC);
- if (status) {
- dbg
- (" usb_submit_urb(read bulk) failed, status = %d",
- status);
- }
- }
- return;
-}
-
-static int get_lsr_info(struct tty_struct *tty,
- struct ATENINTL_port *ATEN2011_port,
- unsigned int __user *value)
-{
- int count;
- unsigned int result = 0;
-
- count = ATEN2011_chars_in_buffer(tty);
- if (count == 0) {
- dbg("%s -- Empty", __func__);
- result = TIOCSER_TEMT;
- }
-
- if (copy_to_user(value, &result, sizeof(int)))
- return -EFAULT;
- return 0;
-}
-
-static int get_number_bytes_avail(struct tty_struct *tty,
- struct ATENINTL_port *ATEN2011_port,
- unsigned int __user *value)
-{
- unsigned int result = 0;
-
- if (!tty)
- return -ENOIOCTLCMD;
-
- result = tty->read_cnt;
-
- dbg("%s(%d) = %d", __func__, ATEN2011_port->port->number, result);
- if (copy_to_user(value, &result, sizeof(int)))
- return -EFAULT;
-
- return -ENOIOCTLCMD;
-}
-
-static int set_modem_info(struct ATENINTL_port *ATEN2011_port, unsigned int cmd,
- unsigned int __user *value)
-{
- unsigned int mcr;
- unsigned int arg;
- __u16 Data;
- int status;
- struct usb_serial_port *port;
-
- if (ATEN2011_port == NULL)
- return -1;
-
- port = (struct usb_serial_port *)ATEN2011_port->port;
-
- mcr = ATEN2011_port->shadowMCR;
-
- if (copy_from_user(&arg, value, sizeof(int)))
- return -EFAULT;
-
- switch (cmd) {
- case TIOCMBIS:
- if (arg & TIOCM_RTS)
- mcr |= MCR_RTS;
- if (arg & TIOCM_DTR)
- mcr |= MCR_RTS;
- if (arg & TIOCM_LOOP)
- mcr |= MCR_LOOPBACK;
- break;
-
- case TIOCMBIC:
- if (arg & TIOCM_RTS)
- mcr &= ~MCR_RTS;
- if (arg & TIOCM_DTR)
- mcr &= ~MCR_RTS;
- if (arg & TIOCM_LOOP)
- mcr &= ~MCR_LOOPBACK;
- break;
-
- case TIOCMSET:
- /* turn off the RTS and DTR and LOOPBACK
- * and then only turn on what was asked to */
- mcr &= ~(MCR_RTS | MCR_DTR | MCR_LOOPBACK);
- mcr |= ((arg & TIOCM_RTS) ? MCR_RTS : 0);
- mcr |= ((arg & TIOCM_DTR) ? MCR_DTR : 0);
- mcr |= ((arg & TIOCM_LOOP) ? MCR_LOOPBACK : 0);
- break;
- }
-
- ATEN2011_port->shadowMCR = mcr;
-
- Data = ATEN2011_port->shadowMCR;
- status = set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
- if (status < 0) {
- dbg("setting MODEM_CONTROL_REGISTER Failed");
- return -1;
- }
-
- return 0;
-}
-
-static int get_modem_info(struct ATENINTL_port *ATEN2011_port,
- unsigned int __user *value)
-{
- unsigned int result = 0;
- __u16 msr;
- unsigned int mcr = ATEN2011_port->shadowMCR;
- int status;
-
- status = get_uart_reg(ATEN2011_port->port, MODEM_STATUS_REGISTER, &msr);
- result = ((mcr & MCR_DTR) ? TIOCM_DTR : 0) /* 0x002 */
- |((mcr & MCR_RTS) ? TIOCM_RTS : 0) /* 0x004 */
- |((msr & ATEN2011_MSR_CTS) ? TIOCM_CTS : 0) /* 0x020 */
- |((msr & ATEN2011_MSR_CD) ? TIOCM_CAR : 0) /* 0x040 */
- |((msr & ATEN2011_MSR_RI) ? TIOCM_RI : 0) /* 0x080 */
- |((msr & ATEN2011_MSR_DSR) ? TIOCM_DSR : 0); /* 0x100 */
-
- dbg("%s -- %x", __func__, result);
-
- if (copy_to_user(value, &result, sizeof(int)))
- return -EFAULT;
- return 0;
-}
-
-static int get_serial_info(struct ATENINTL_port *ATEN2011_port,
- struct serial_struct __user *retinfo)
-{
- struct serial_struct tmp;
-
- if (ATEN2011_port == NULL)
- return -1;
-
- if (!retinfo)
- return -EFAULT;
-
- memset(&tmp, 0, sizeof(tmp));
-
- tmp.type = PORT_16550A;
- tmp.line = ATEN2011_port->port->serial->minor;
- if (tmp.line == SERIAL_TTY_NO_MINOR)
- tmp.line = 0;
- tmp.port = ATEN2011_port->port->number;
- tmp.irq = 0;
- tmp.flags = ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ;
- tmp.xmit_fifo_size = NUM_URBS * URB_TRANSFER_BUFFER_SIZE;
- tmp.baud_base = 9600;
- tmp.close_delay = 5 * HZ;
- tmp.closing_wait = 30 * HZ;
-
- if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
- return -EFAULT;
- return 0;
-}
-
-static int ATEN2011_ioctl(struct tty_struct *tty, struct file *file,
- unsigned int cmd, unsigned long arg)
-{
- struct usb_serial_port *port = tty->driver_data;
- struct ATENINTL_port *ATEN2011_port;
- struct async_icount cnow;
- struct async_icount cprev;
- struct serial_icounter_struct icount;
- int ATENret = 0;
- unsigned int __user *user_arg = (unsigned int __user *)arg;
-
- ATEN2011_port = usb_get_serial_port_data(port);
-
- if (ATEN2011_port == NULL)
- return -1;
-
- dbg("%s - port %d, cmd = 0x%x", __func__, port->number, cmd);
-
- switch (cmd) {
- /* return number of bytes available */
-
- case TIOCINQ:
- dbg("%s (%d) TIOCINQ", __func__, port->number);
- return get_number_bytes_avail(tty, ATEN2011_port, user_arg);
- break;
-
- case TIOCOUTQ:
- dbg("%s (%d) TIOCOUTQ", __func__, port->number);
- return put_user(ATEN2011_chars_in_buffer(tty), user_arg);
- break;
-
- case TIOCSERGETLSR:
- dbg("%s (%d) TIOCSERGETLSR", __func__, port->number);
- return get_lsr_info(tty, ATEN2011_port, user_arg);
- return 0;
-
- case TIOCMBIS:
- case TIOCMBIC:
- case TIOCMSET:
- dbg("%s (%d) TIOCMSET/TIOCMBIC/TIOCMSET", __func__,
- port->number);
- ATENret = set_modem_info(ATEN2011_port, cmd, user_arg);
- return ATENret;
-
- case TIOCMGET:
- dbg("%s (%d) TIOCMGET", __func__, port->number);
- return get_modem_info(ATEN2011_port, user_arg);
-
- case TIOCGSERIAL:
- dbg("%s (%d) TIOCGSERIAL", __func__, port->number);
- return get_serial_info(ATEN2011_port,
- (struct serial_struct __user *)arg);
-
- case TIOCSSERIAL:
- dbg("%s (%d) TIOCSSERIAL", __func__, port->number);
- break;
-
- case TIOCMIWAIT:
- dbg("%s (%d) TIOCMIWAIT", __func__, port->number);
- cprev = ATEN2011_port->icount;
- while (1) {
- /* see if a signal did it */
- if (signal_pending(current))
- return -ERESTARTSYS;
- cnow = ATEN2011_port->icount;
- if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr &&
- cnow.dcd == cprev.dcd && cnow.cts == cprev.cts)
- return -EIO; /* no change => error */
- if (((arg & TIOCM_RNG) && (cnow.rng != cprev.rng)) ||
- ((arg & TIOCM_DSR) && (cnow.dsr != cprev.dsr)) ||
- ((arg & TIOCM_CD) && (cnow.dcd != cprev.dcd)) ||
- ((arg & TIOCM_CTS) && (cnow.cts != cprev.cts))) {
- return 0;
- }
- cprev = cnow;
- }
- /* NOTREACHED */
- break;
-
- case TIOCGICOUNT:
- cnow = ATEN2011_port->icount;
- icount.cts = cnow.cts;
- icount.dsr = cnow.dsr;
- icount.rng = cnow.rng;
- icount.dcd = cnow.dcd;
- icount.rx = cnow.rx;
- icount.tx = cnow.tx;
- icount.frame = cnow.frame;
- icount.overrun = cnow.overrun;
- icount.parity = cnow.parity;
- icount.brk = cnow.brk;
- icount.buf_overrun = cnow.buf_overrun;
-
- dbg("%s (%d) TIOCGICOUNT RX=%d, TX=%d", __func__,
- port->number, icount.rx, icount.tx);
- if (copy_to_user((void __user *)arg, &icount, sizeof(icount)))
- return -EFAULT;
- return 0;
-
- default:
- break;
- }
-
- return -ENOIOCTLCMD;
-}
-
-static int ATEN2011_calc_baud_rate_divisor(int baudRate, int *divisor,
- __u16 *clk_sel_val)
-{
- dbg("%s - %d", __func__, baudRate);
-
- if (baudRate <= 115200) {
- *divisor = 115200 / baudRate;
- *clk_sel_val = 0x0;
- }
- if ((baudRate > 115200) && (baudRate <= 230400)) {
- *divisor = 230400 / baudRate;
- *clk_sel_val = 0x10;
- } else if ((baudRate > 230400) && (baudRate <= 403200)) {
- *divisor = 403200 / baudRate;
- *clk_sel_val = 0x20;
- } else if ((baudRate > 403200) && (baudRate <= 460800)) {
- *divisor = 460800 / baudRate;
- *clk_sel_val = 0x30;
- } else if ((baudRate > 460800) && (baudRate <= 806400)) {
- *divisor = 806400 / baudRate;
- *clk_sel_val = 0x40;
- } else if ((baudRate > 806400) && (baudRate <= 921600)) {
- *divisor = 921600 / baudRate;
- *clk_sel_val = 0x50;
- } else if ((baudRate > 921600) && (baudRate <= 1572864)) {
- *divisor = 1572864 / baudRate;
- *clk_sel_val = 0x60;
- } else if ((baudRate > 1572864) && (baudRate <= 3145728)) {
- *divisor = 3145728 / baudRate;
- *clk_sel_val = 0x70;
- }
- return 0;
-}
-
-static int ATEN2011_send_cmd_write_baud_rate(struct ATENINTL_port
- *ATEN2011_port, int baudRate)
-{
- int divisor = 0;
- int status;
- __u16 Data;
- unsigned char number;
- __u16 clk_sel_val;
- struct usb_serial_port *port;
- int minor;
-
- if (ATEN2011_port == NULL)
- return -1;
-
- port = (struct usb_serial_port *)ATEN2011_port->port;
-
- dbg("%s", "Entering .......... ");
-
- minor = ATEN2011_port->port->serial->minor;
- if (minor == SERIAL_TTY_NO_MINOR)
- minor = 0;
- number = ATEN2011_port->port->number - minor;
-
- dbg("%s - port = %d, baud = %d", __func__,
- ATEN2011_port->port->number, baudRate);
- /* reset clk_uart_sel in spregOffset */
- if (baudRate > 115200) {
-#ifdef HW_flow_control
- /*
- * NOTE: need to see the pther register to modify
- * setting h/w flow control bit to 1;
- */
- /* Data = ATEN2011_port->shadowMCR; */
- Data = 0x2b;
- ATEN2011_port->shadowMCR = Data;
- status = set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
- if (status < 0) {
- dbg("Writing spreg failed in set_serial_baud");
- return -1;
- }
-#endif
-
- } else {
-#ifdef HW_flow_control
- /* setting h/w flow control bit to 0; */
- /* Data = ATEN2011_port->shadowMCR; */
- Data = 0xb;
- ATEN2011_port->shadowMCR = Data;
- status = set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
- if (status < 0) {
- dbg("Writing spreg failed in set_serial_baud");
- return -1;
- }
-#endif
-
- }
-
- if (1) /* baudRate <= 115200) */ {
- clk_sel_val = 0x0;
- Data = 0x0;
- status =
- ATEN2011_calc_baud_rate_divisor(baudRate, &divisor,
- &clk_sel_val);
- status = get_reg_sync(port, ATEN2011_port->SpRegOffset, &Data);
- if (status < 0) {
- dbg("reading spreg failed in set_serial_baud");
- return -1;
- }
- Data = (Data & 0x8f) | clk_sel_val;
- status = set_reg_sync(port, ATEN2011_port->SpRegOffset, Data);
- if (status < 0) {
- dbg("Writing spreg failed in set_serial_baud");
- return -1;
- }
- /* Calculate the Divisor */
-
- if (status) {
- err("%s - bad baud rate", __func__);
- dbg("%s", "bad baud rate");
- return status;
- }
- /* Enable access to divisor latch */
- Data = ATEN2011_port->shadowLCR | SERIAL_LCR_DLAB;
- ATEN2011_port->shadowLCR = Data;
- set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
-
- /* Write the divisor */
- Data = (unsigned char)(divisor & 0xff);
- dbg("set_serial_baud Value to write DLL is %x", Data);
- set_uart_reg(port, DIVISOR_LATCH_LSB, Data);
-
- Data = (unsigned char)((divisor & 0xff00) >> 8);
- dbg("set_serial_baud Value to write DLM is %x", Data);
- set_uart_reg(port, DIVISOR_LATCH_MSB, Data);
-
- /* Disable access to divisor latch */
- Data = ATEN2011_port->shadowLCR & ~SERIAL_LCR_DLAB;
- ATEN2011_port->shadowLCR = Data;
- set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
-
- }
-
- return status;
-}
-
-static void ATEN2011_change_port_settings(struct tty_struct *tty,
- struct ATENINTL_port *ATEN2011_port,
- struct ktermios *old_termios)
-{
- int baud;
- unsigned cflag;
- unsigned iflag;
- __u8 lData;
- __u8 lParity;
- __u8 lStop;
- int status;
- __u16 Data;
- struct usb_serial_port *port;
- struct usb_serial *serial;
-
- if (ATEN2011_port == NULL)
- return;
-
- port = (struct usb_serial_port *)ATEN2011_port->port;
-
- serial = port->serial;
-
- dbg("%s - port %d", __func__, ATEN2011_port->port->number);
-
- if (!ATEN2011_port->open) {
- dbg("%s - port not opened", __func__);
- return;
- }
-
- if ((!tty) || (!tty->termios)) {
- dbg("%s - no tty structures", __func__);
- return;
- }
-
- dbg("%s", "Entering .......... ");
-
- lData = LCR_BITS_8;
- lStop = LCR_STOP_1;
- lParity = LCR_PAR_NONE;
-
- cflag = tty->termios->c_cflag;
- iflag = tty->termios->c_iflag;
-
- /* Change the number of bits */
-
- /* COMMENT1: the below Line"if(cflag & CSIZE)" is added for the errors we get for serial loop data test i.e serial_loopback.pl -v */
- /* if(cflag & CSIZE) */
- {
- switch (cflag & CSIZE) {
- case CS5:
- lData = LCR_BITS_5;
- break;
-
- case CS6:
- lData = LCR_BITS_6;
- break;
-
- case CS7:
- lData = LCR_BITS_7;
- break;
- default:
- case CS8:
- lData = LCR_BITS_8;
- break;
- }
- }
- /* Change the Parity bit */
- if (cflag & PARENB) {
- if (cflag & PARODD) {
- lParity = LCR_PAR_ODD;
- dbg("%s - parity = odd", __func__);
- } else {
- lParity = LCR_PAR_EVEN;
- dbg("%s - parity = even", __func__);
- }
-
- } else {
- dbg("%s - parity = none", __func__);
- }
-
- if (cflag & CMSPAR)
- lParity = lParity | 0x20;
-
- /* Change the Stop bit */
- if (cflag & CSTOPB) {
- lStop = LCR_STOP_2;
- dbg("%s - stop bits = 2", __func__);
- } else {
- lStop = LCR_STOP_1;
- dbg("%s - stop bits = 1", __func__);
- }
-
- /* Update the LCR with the correct value */
- ATEN2011_port->shadowLCR &=
- ~(LCR_BITS_MASK | LCR_STOP_MASK | LCR_PAR_MASK);
- ATEN2011_port->shadowLCR |= (lData | lParity | lStop);
-
- dbg
- ("ATEN2011_change_port_settings ATEN2011_port->shadowLCR is %x",
- ATEN2011_port->shadowLCR);
- /* Disable Interrupts */
- Data = 0x00;
- set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
-
- Data = 0x00;
- set_uart_reg(port, FIFO_CONTROL_REGISTER, Data);
-
- Data = 0xcf;
- set_uart_reg(port, FIFO_CONTROL_REGISTER, Data);
-
- /* Send the updated LCR value to the ATEN2011 */
- Data = ATEN2011_port->shadowLCR;
-
- set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
-
- Data = 0x00b;
- ATEN2011_port->shadowMCR = Data;
- set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
- Data = 0x00b;
- set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
-
- /* set up the MCR register and send it to the ATEN2011 */
-
- ATEN2011_port->shadowMCR = MCR_MASTER_IE;
- if (cflag & CBAUD)
- ATEN2011_port->shadowMCR |= (MCR_DTR | MCR_RTS);
-
- if (cflag & CRTSCTS)
- ATEN2011_port->shadowMCR |= (MCR_XON_ANY);
- else
- ATEN2011_port->shadowMCR &= ~(MCR_XON_ANY);
-
- Data = ATEN2011_port->shadowMCR;
- set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
-
- /* Determine divisor based on baud rate */
- baud = tty_get_baud_rate(tty);
-
- if (!baud) {
- /* pick a default, any default... */
- dbg("%s", "Picked default baud...");
- baud = 9600;
- }
-
- dbg("%s - baud rate = %d", __func__, baud);
- status = ATEN2011_send_cmd_write_baud_rate(ATEN2011_port, baud);
-
- /* Enable Interrupts */
- Data = 0x0c;
- set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
-
- if (ATEN2011_port->read_urb->status != -EINPROGRESS) {
- ATEN2011_port->read_urb->dev = serial->dev;
-
- status = usb_submit_urb(ATEN2011_port->read_urb, GFP_ATOMIC);
-
- if (status) {
- dbg
- (" usb_submit_urb(read bulk) failed, status = %d",
- status);
- }
- }
- dbg
- ("ATEN2011_change_port_settings ATEN2011_port->shadowLCR is End %x",
- ATEN2011_port->shadowLCR);
-
- return;
-}
-
-static int ATEN2011_calc_num_ports(struct usb_serial *serial)
-{
-
- __u16 Data = 0x00;
- int ret = 0;
- int ATEN2011_2or4ports;
- ret = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
- ATEN_RDREQ, ATEN_RD_RTYPE, 0, GPIO_REGISTER,
- &Data, VENDOR_READ_LENGTH, ATEN_WDR_TIMEOUT);
-
-/* ghostgum: here is where the problem appears to bet */
-/* Which of the following are needed? */
-/* Greg used the serial->type->num_ports=2 */
-/* But the code in the ATEN2011_open relies on serial->num_ports=2 */
- if ((Data & 0x01) == 0) {
- ATEN2011_2or4ports = 2;
- serial->type->num_ports = 2;
- serial->num_ports = 2;
- }
- /* else if(serial->interface->cur_altsetting->desc.bNumEndpoints == 9) */
- else {
- ATEN2011_2or4ports = 4;
- serial->type->num_ports = 4;
- serial->num_ports = 4;
-
- }
-
- return ATEN2011_2or4ports;
-}
-
-static int ATEN2011_startup(struct usb_serial *serial)
-{
- struct ATENINTL_serial *ATEN2011_serial;
- struct ATENINTL_port *ATEN2011_port;
- struct usb_device *dev;
- int i, status;
- int minor;
-
- __u16 Data;
- dbg("%s", " ATEN2011_startup :entering..........");
-
- if (!serial) {
- dbg("%s", "Invalid Handler");
- return -1;
- }
-
- dev = serial->dev;
-
- dbg("%s", "Entering...");
-
- /* create our private serial structure */
- ATEN2011_serial = kzalloc(sizeof(struct ATENINTL_serial), GFP_KERNEL);
- if (ATEN2011_serial == NULL) {
- err("%s - Out of memory", __func__);
- return -ENOMEM;
- }
-
- /* resetting the private structure field values to zero */
- memset(ATEN2011_serial, 0, sizeof(struct ATENINTL_serial));
-
- ATEN2011_serial->serial = serial;
- /* initilize status polling flag to 0 */
- ATEN2011_serial->status_polling_started = 0;
-
- usb_set_serial_data(serial, ATEN2011_serial);
- ATEN2011_serial->ATEN2011_spectrum_2or4ports =
- ATEN2011_calc_num_ports(serial);
- /* we set up the pointers to the endpoints in the ATEN2011_open *
- * function, as the structures aren't created yet. */
-
- /* set up port private structures */
- for (i = 0; i < serial->num_ports; ++i) {
- ATEN2011_port =
- kmalloc(sizeof(struct ATENINTL_port), GFP_KERNEL);
- if (ATEN2011_port == NULL) {
- err("%s - Out of memory", __func__);
- usb_set_serial_data(serial, NULL);
- kfree(ATEN2011_serial);
- return -ENOMEM;
- }
- memset(ATEN2011_port, 0, sizeof(struct ATENINTL_port));
-
- /*
- * Initialize all port interrupt end point to port 0
- * int endpoint. Our device has only one interrupt end point
- * comman to all port
- */
- /* serial->port[i]->interrupt_in_endpointAddress = serial->port[0]->interrupt_in_endpointAddress; */
-
- ATEN2011_port->port = serial->port[i];
- usb_set_serial_port_data(serial->port[i], ATEN2011_port);
-
- minor = serial->port[i]->serial->minor;
- if (minor == SERIAL_TTY_NO_MINOR)
- minor = 0;
- ATEN2011_port->port_num =
- ((serial->port[i]->number - minor) + 1);
-
- if (ATEN2011_port->port_num == 1) {
- ATEN2011_port->SpRegOffset = 0x0;
- ATEN2011_port->ControlRegOffset = 0x1;
- ATEN2011_port->DcrRegOffset = 0x4;
- } else if ((ATEN2011_port->port_num == 2)
- && (ATEN2011_serial->ATEN2011_spectrum_2or4ports ==
- 4)) {
- ATEN2011_port->SpRegOffset = 0x8;
- ATEN2011_port->ControlRegOffset = 0x9;
- ATEN2011_port->DcrRegOffset = 0x16;
- } else if ((ATEN2011_port->port_num == 2)
- && (ATEN2011_serial->ATEN2011_spectrum_2or4ports ==
- 2)) {
- ATEN2011_port->SpRegOffset = 0xa;
- ATEN2011_port->ControlRegOffset = 0xb;
- ATEN2011_port->DcrRegOffset = 0x19;
- } else if ((ATEN2011_port->port_num == 3)
- && (ATEN2011_serial->ATEN2011_spectrum_2or4ports ==
- 4)) {
- ATEN2011_port->SpRegOffset = 0xa;
- ATEN2011_port->ControlRegOffset = 0xb;
- ATEN2011_port->DcrRegOffset = 0x19;
- } else if ((ATEN2011_port->port_num == 4)
- && (ATEN2011_serial->ATEN2011_spectrum_2or4ports ==
- 4)) {
- ATEN2011_port->SpRegOffset = 0xc;
- ATEN2011_port->ControlRegOffset = 0xd;
- ATEN2011_port->DcrRegOffset = 0x1c;
- }
-
- usb_set_serial_port_data(serial->port[i], ATEN2011_port);
-
- /* enable rx_disable bit in control register */
-
- status = get_reg_sync(serial->port[i],
- ATEN2011_port->ControlRegOffset, &Data);
- if (status < 0) {
- dbg("Reading ControlReg failed status-0x%x",
- status);
- break;
- } else
- dbg
- ("ControlReg Reading success val is %x, status%d",
- Data, status);
- Data |= 0x08; /* setting driver done bit */
- Data |= 0x04; /* sp1_bit to have cts change reflect in modem status reg */
-
- /* Data |= 0x20; */ /* rx_disable bit */
- status = set_reg_sync(serial->port[i],
- ATEN2011_port->ControlRegOffset, Data);
- if (status < 0) {
- dbg
- ("Writing ControlReg failed(rx_disable) status-0x%x",
- status);
- break;
- } else
- dbg
- ("ControlReg Writing success(rx_disable) status%d",
- status);
-
- /*
- * Write default values in DCR (i.e 0x01 in DCR0, 0x05 in DCR2
- * and 0x24 in DCR3
- */
- Data = 0x01;
- status = set_reg_sync(serial->port[i],
- (__u16)(ATEN2011_port->DcrRegOffset + 0),
- Data);
- if (status < 0) {
- dbg("Writing DCR0 failed status-0x%x", status);
- break;
- } else
- dbg("DCR0 Writing success status%d", status);
-
- Data = 0x05;
- status = set_reg_sync(serial->port[i],
- (__u16)(ATEN2011_port->DcrRegOffset + 1),
- Data);
- if (status < 0) {
- dbg("Writing DCR1 failed status-0x%x", status);
- break;
- } else
- dbg("DCR1 Writing success status%d", status);
-
- Data = 0x24;
- status = set_reg_sync(serial->port[i],
- (__u16)(ATEN2011_port->DcrRegOffset + 2),
- Data);
- if (status < 0) {
- dbg("Writing DCR2 failed status-0x%x", status);
- break;
- } else
- dbg("DCR2 Writing success status%d", status);
-
- /* write values in clkstart0x0 and clkmulti 0x20 */
- Data = 0x0;
- status = set_reg_sync(serial->port[i], CLK_START_VALUE_REGISTER,
- Data);
- if (status < 0) {
- dbg
- ("Writing CLK_START_VALUE_REGISTER failed status-0x%x",
- status);
- break;
- } else
- dbg
- ("CLK_START_VALUE_REGISTER Writing success status%d",
- status);
-
- Data = 0x20;
- status = set_reg_sync(serial->port[i], CLK_MULTI_REGISTER,
- Data);
- if (status < 0) {
- dbg
- ("Writing CLK_MULTI_REGISTER failed status-0x%x",
- status);
- break;
- } else
- dbg("CLK_MULTI_REGISTER Writing success status%d",
- status);
-
- /* Zero Length flag register */
- if ((ATEN2011_port->port_num != 1)
- && (ATEN2011_serial->ATEN2011_spectrum_2or4ports == 2)) {
-
- Data = 0xff;
- status = set_reg_sync(serial->port[i],
- (__u16)(ZLP_REG1 + ((__u16)ATEN2011_port->port_num)),
- Data);
- dbg("ZLIP offset%x",
- (__u16) (ZLP_REG1 +
- ((__u16) ATEN2011_port->port_num)));
- if (status < 0) {
- dbg
- ("Writing ZLP_REG%d failed status-0x%x",
- i + 2, status);
- break;
- } else
- dbg("ZLP_REG%d Writing success status%d",
- i + 2, status);
- } else {
- Data = 0xff;
- status = set_reg_sync(serial->port[i],
- (__u16)(ZLP_REG1 + ((__u16)ATEN2011_port->port_num) - 0x1),
- Data);
- dbg("ZLIP offset%x",
- (__u16) (ZLP_REG1 +
- ((__u16) ATEN2011_port->port_num) -
- 0x1));
- if (status < 0) {
- dbg
- ("Writing ZLP_REG%d failed status-0x%x",
- i + 1, status);
- break;
- } else
- dbg("ZLP_REG%d Writing success status%d",
- i + 1, status);
-
- }
- ATEN2011_port->control_urb = usb_alloc_urb(0, GFP_ATOMIC);
- ATEN2011_port->ctrl_buf = kmalloc(16, GFP_KERNEL);
-
- }
-
- /* Zero Length flag enable */
- Data = 0x0f;
- status = set_reg_sync(serial->port[0], ZLP_REG5, Data);
- if (status < 0) {
- dbg("Writing ZLP_REG5 failed status-0x%x", status);
- return -1;
- } else
- dbg("ZLP_REG5 Writing success status%d", status);
-
- /* setting configuration feature to one */
- usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0),
- (__u8) 0x03, 0x00, 0x01, 0x00, NULL, 0x00, 5 * HZ);
- return 0;
-}
-
-static void ATEN2011_release(struct usb_serial *serial)
-{
- int i;
- struct ATENINTL_port *ATEN2011_port;
-
- /* check for the ports to be closed,close the ports and disconnect */
-
- /* free private structure allocated for serial port *
- * stop reads and writes on all ports */
-
- for (i = 0; i < serial->num_ports; ++i) {
- ATEN2011_port = usb_get_serial_port_data(serial->port[i]);
- kfree(ATEN2011_port->ctrl_buf);
- usb_kill_urb(ATEN2011_port->control_urb);
- kfree(ATEN2011_port);
- usb_set_serial_port_data(serial->port[i], NULL);
- }
-
- /* free private structure allocated for serial device */
-
- kfree(usb_get_serial_data(serial));
- usb_set_serial_data(serial, NULL);
-}
-
-static struct usb_serial_driver aten_serial_driver = {
- .driver = {
- .owner = THIS_MODULE,
- .name = "aten2011",
- },
- .description = DRIVER_DESC,
- .id_table = id_table,
- .open = ATEN2011_open,
- .close = ATEN2011_close,
- .write = ATEN2011_write,
- .write_room = ATEN2011_write_room,
- .chars_in_buffer = ATEN2011_chars_in_buffer,
- .throttle = ATEN2011_throttle,
- .unthrottle = ATEN2011_unthrottle,
- .calc_num_ports = ATEN2011_calc_num_ports,
-
- .ioctl = ATEN2011_ioctl,
- .set_termios = ATEN2011_set_termios,
- .break_ctl = ATEN2011_break,
- .tiocmget = ATEN2011_tiocmget,
- .tiocmset = ATEN2011_tiocmset,
- .attach = ATEN2011_startup,
- .release = ATEN2011_release,
- .read_bulk_callback = ATEN2011_bulk_in_callback,
- .read_int_callback = ATEN2011_interrupt_callback,
-};
-
-static struct usb_driver aten_driver = {
- .name = "aten2011",
- .probe = usb_serial_probe,
- .disconnect = usb_serial_disconnect,
- .id_table = id_table,
-};
-
-static int __init aten_init(void)
-{
- int retval;
-
- /* Register with the usb serial */
- retval = usb_serial_register(&aten_serial_driver);
- if (retval)
- return retval;
-
- printk(KERN_INFO KBUILD_MODNAME ":"
- DRIVER_DESC " " DRIVER_VERSION "\n");
-
- /* Register with the usb */
- retval = usb_register(&aten_driver);
- if (retval)
- usb_serial_deregister(&aten_serial_driver);
-
- return retval;
-}
-
-static void __exit aten_exit(void)
-{
- usb_deregister(&aten_driver);
- usb_serial_deregister(&aten_serial_driver);
-}
-
-module_init(aten_init);
-module_exit(aten_exit);
-
-/* Module information */
-MODULE_DESCRIPTION(DRIVER_DESC);
-MODULE_LICENSE("GPL");
-
-MODULE_PARM_DESC(debug, "Debug enabled or not");
--
1.6.3.2
More information about the devel
mailing list